ขนาดวิดีโอ: 1280 X 720853 X 480640 X 360
แสดงแผงควบคุมโปรแกรมเล่น
เล่นอัตโนมัติ
เล่นใหม่
What camera are you using you using?
This low profile vise is awesome
Top
What brand/specific single flute end mills are you using?
3/8" Single Flute - 5640A - www.cutter-shop.com/5600aseries.html1/4" Single Flute - 1111A-025 - uk.cncshop.com/products/1111a-025-belin-33635-1-4-dia-1-4-shk-5-8-cut?variant=323217203528524mm Single Flute - EA1S-04041545DLC - www.shop-apt.co.uk/1-flute-carbide-end-mills-for-aluminium-dlc-coated/4mm-diameter-1-flute-carbide-end-mill-for-aluminium-15mm-flute-length-dlc-coated.html
Do you think that i can do that with a regular 3018 or i need a upgrade?
A regular 3018 should be fine. I've machined HDPE on one with good results. Just make sure to use a decent quality carbide end mill.
Very good looking chips!
Looked like snow!
where to buy the vise?
www.inceptionmachines.co.uk/low-profile-vice
I'd be more a bit more forthcoming with setup/settings (e.g., SFM, air assist).
The video contains details on rpm, feed per tooth, stepover etc. No air blast was used for this.
@@GeorgeLaight do you have a link to this vise, I could need it
@@luks9203 www.inceptionmachines.co.uk/inception-machines-store/low-profile-vice
Awesome video !!! thank you so much , helped me tremendously 👌👍
if you dont have a air assist , 3d print a fan that simply slider onto the shaft of your endmill th help clear chips
What camera are you using you using?
This low profile vise is awesome
Top
What brand/specific single flute end mills are you using?
3/8" Single Flute - 5640A - www.cutter-shop.com/5600aseries.html
1/4" Single Flute - 1111A-025 - uk.cncshop.com/products/1111a-025-belin-33635-1-4-dia-1-4-shk-5-8-cut?variant=32321720352852
4mm Single Flute - EA1S-04041545DLC - www.shop-apt.co.uk/1-flute-carbide-end-mills-for-aluminium-dlc-coated/4mm-diameter-1-flute-carbide-end-mill-for-aluminium-15mm-flute-length-dlc-coated.html
Do you think that i can do that with a regular 3018 or i need a upgrade?
A regular 3018 should be fine. I've machined HDPE on one with good results. Just make sure to use a decent quality carbide end mill.
Very good looking chips!
Looked like snow!
where to buy the vise?
www.inceptionmachines.co.uk/low-profile-vice
I'd be more a bit more forthcoming with setup/settings (e.g., SFM, air assist).
The video contains details on rpm, feed per tooth, stepover etc. No air blast was used for this.
@@GeorgeLaight do you have a link to this vise, I could need it
@@luks9203 www.inceptionmachines.co.uk/inception-machines-store/low-profile-vice
Awesome video !!! thank you so much , helped me tremendously 👌👍
if you dont have a air assist , 3d print a fan that simply slider onto the shaft of your endmill th help clear chips