I apologize for the mistake if I have made in this restoration !!!Thank you for watching the video. Don't forget to like and subscribe to channels Link Subscriber: BIT.ly/44DFJVB
I used to overhaul and rewind electric motors for an employer over 20 years ago &; the procedure was:- 1. Measure the winding resistance in Ohms 2. Test the insulation with an Insulation tester between phases after the stator leads have been disconnected from the terminal block & from phase to earth at 500 VDC for a 240 VAC single phase motor or 1000 VDC for a 3 phase electric motor. 3. Wash the windings out with electrical cleaning solvent if the windings are good otherwise strip that windings out, collect the data & rewind the stator windings. 4. Bake the motor frame & windings in an oven for 1 hour, Clean the end shields & clean the rotor, varnish the end of the rotor, inside of the end shields & after the we winding has cooled down spray them with Isonel spray varnish 5. Fur new bearings & seals onto the rotor 6 . Reassemble the motor then rest the current drawn from the supply again
What happened to the young men who started and built up this channel? Did the government take over their channel/business? Where are they? Are they OK?
@@dtrestoration8590 What happened to the young men who started and built up this channel? Did the government take over their channel/business? Where are they? Are they OK?
I apologize for the mistake if I have made in this restoration !!!Thank you for watching the video. Don't forget to like and subscribe to channels
Link Subscriber: BIT.ly/44DFJVB
QUE TRABAJO DE CALIDAD,, LE DESEO MUCHO ÉXITO..
Thank you watching video!!!
نجاح مضمون ١٠٠/١٠٠
أيادي ملفوفه بالذهب ❤❤
Thank you watching video!!!
well done mate top notch job looks awesome
Thank you watching video!!!
Good job of the restorations😊😊😊😊❤❤💪💪💪💪💪💪👍👍👍👍👍👍😯😯😯😯
Thank you watching video
❤SALUT PRIETENE FELICITARI FRUMOS BINE LUCRAT 😊
Vă mulțumesc că vizionați videoclipul
🙏👍🏻👍🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
Thank you watching video!!!
I used to overhaul and rewind electric motors for an employer over 20 years ago &; the procedure was:-
1. Measure the winding resistance in Ohms
2. Test the insulation with an Insulation tester between phases after the stator leads have been disconnected from the terminal block & from phase to earth at 500 VDC for a 240 VAC single phase motor or 1000 VDC for a 3 phase electric motor.
3. Wash the windings out with electrical cleaning solvent if the windings are good otherwise strip that windings out, collect the data & rewind the stator windings.
4. Bake the motor frame & windings in an oven for 1 hour, Clean the end shields & clean the rotor, varnish the end of the rotor, inside of the end shields & after the we winding has cooled down spray them with Isonel spray varnish
5. Fur new bearings & seals onto the rotor
6 . Reassemble the motor then rest the current drawn from the supply again
Thank you watching video!!!
👌
It would have been funny if you would have cut the scooter in half
Mencionen que clase de líquido usan porfa.
Thank you watching video!!!
Engine’s run on gas. That is a motor.
Thank you watching video!!!
lasy job!!!!!!
👍🤝🇨🇺🇷🇺🙏👈
What happened to the young men who started and built up this channel? Did the government take over their channel/business? Where are they? Are they OK?
Thank you watching video!!!
@@dtrestoration8590 What happened to the young men who started and built up this channel? Did the government take over their channel/business? Where are they? Are they OK?
SUPER 🥰✋✋✋✋👍👍👍🤍❤POLAND
Thank you watching video!!!
Нарезалка пенопласта, ептваюмать!