Your Tip saved a lot of aggravation for me, have many car radios Cheap and good ones and i was almost going to swap this one out as it has too many settings. and in the future, I probably will give to my young grandson. might still but at least i got this one sorted out. like most Chinese manuals, they need a lot of explaining with a good vid like yours.
Glad the video was helpful, Robert. It's always good to hear someone found value in my videos. I found these radios aren't very intuitive when going through the settings, I actually refer back to this video myself sometimes if I haven't used this radio for a while as I forget what to do. Cheers mate! 🙂👍
Haha yeah it's easy. I often forget how if I haven't used this transmitter for a while and have to watch my own video again. Glad it was helpful to you! 👍
Hey thanks for video, I have a little issue with my car, when it’s in normal mode and I pull the trigger I only get like 50% forward and when I push the trigger I get 100% reverse, seams like I have to keep it reverse for the throttle, is that normal? Thanks
Hi. Yeah that’s fine to keep it reversed, as long as when you pull the trigger the car goes forward and you have brake/reverse when you push the trigger forward. 👍
There is a couple of ways. Firstly, try reversing you throttle channel (usually channel 2). If you're running a brushless motor, you could swap any TWO of the three motor wires around. If your have a brushed motor, you can swap the two motor wires around. Hope this helps. 👍
Since i reversed my throttle servo on my nitro buggy, servo has no trim fir throttle, all trim is for the brake now...what gives?...idle has to be set with s rewdriver or by hand when starting
Nice .problem im having is figureing out how to turn down the throttle on reverse..way to much reverse..Id like it to brake a little longer not slap into reverse..Im running a LRP AI super reverse digital ,its auto no settings .So i have to adjust it on radio.I got good throttle but seems like not enough brake before it goes into reverse..any info i would appreciate.thanks all
Thanks! Hmm, that one I'm not 100% sure about. I think that is more of an ESC issue but since you can't change the setup on your ESC, maybe try turning down the EPA (end point adjustment) on the transmitter. I doubt this will solve the problem, but it may help a little. 👍
@@RCHobbyShed just wanted to share EastSide RC posted some helpful stuff also...and yes the epa did work ,went down to like 70 % on reverse throttle ,it is much better.But yea that esc is wacked..Super reverse ,no joke there..lol
I was able to figure this out on myself, but for some reason, when I pull on the throttle, the car goes backwards, and when I push the throttle, it goes forwards. This happened both in reverse mode and normal mode. If anyone can help, please lmk. Thx
That's very strange. Are you sure you're reversing the correct channel, (Ch2)? If that doesn't work and you're running a brushless motor, you can try swapping two of the motor wires around. Leave the 3rd wire as is, only swap 2 wires. Hope this helps.
Thanks for this man . Was scratching my head for a good 15 minutes trying to figure this out . Legend!!!!!!!!!
Glad it was helpful. I was scratching my head too at first. 👍
Your Tip saved a lot of aggravation for me, have many car radios Cheap and good ones and i was almost going to swap this one out as it has too many settings. and in the future, I probably will give to my young grandson. might still but at least i got this one sorted out. like most Chinese manuals, they need a lot of explaining with a good vid like yours.
Glad the video was helpful, Robert. It's always good to hear someone found value in my videos. I found these radios aren't very intuitive when going through the settings, I actually refer back to this video myself sometimes if I haven't used this radio for a while as I forget what to do. Cheers mate! 🙂👍
I couldn't get it to work and then I watched your video and I fixed it thanks man my losi dbxl works now
Glad it helped. Ooh DBXL, very nice. Have fun Robert! 👍
Aye thanks dawg actually because of this video I figured out how to tune my crawler pretty well though out all the settings lol thanks again
Out in the field and all I can say is thank you
short but epic tip, thanks!
I was really need that tip, thanks for share.
Thanks for that. I definitely needed this info!😊
What the heck...that's all? I was getting frustrated as all get out trying to figure this out lol. Thanks!
Haha yeah it's easy. I often forget how if I haven't used this transmitter for a while and have to watch my own video again. Glad it was helpful to you! 👍
This was very helpful, I could figure it out before I watched this👍👍👍👍
Thanks for watching. Good to know it helped. 🙂👍
Thanks!!
I appreciate 🙏 Thank you 😊
Thanks Mate👍
Great info.
Thanks for this! I was a little stumped myself.
Good to know it was helpful. Sorry for my slow reply. 🙂👍
Right on man!! ❤
Thx very helpful
saved me bacon ....thank you 😎😎
I'm glad the video was helpful. 🙂👍
This is great but how do I reverse my throttle as when I pull the trigger left is forward?
Thanks man !!!!
Thanks a bunch!
Thanks you very much for your help..
You're welcome! 👍
Thank you 😊 👍👍👍
You're welcome 👍
many thanks
How do you increase the steering ratio ?
Hey thanks for video, I have a little issue with my car, when it’s in normal mode and I pull the trigger I only get like 50% forward and when I push the trigger I get 100% reverse, seams like I have to keep it reverse for the throttle, is that normal? Thanks
Hi. Yeah that’s fine to keep it reversed, as long as when you pull the trigger the car goes forward and you have brake/reverse when you push the trigger forward. 👍
You have to do it in the car not the remote you switch the motor wires
you saved me thank you
Thank you
thanks man
No probs! 🙂👍
Hi when I pull my trigger the car goes backwards and when I push the trigger it goes forever can u help
There is a couple of ways. Firstly, try reversing you throttle channel (usually channel 2). If you're running a brushless motor, you could swap any TWO of the three motor wires around. If your have a brushed motor, you can swap the two motor wires around.
Hope this helps. 👍
Thanks very much it works Now 😀👍
@@jonathanhumphreys1971 Awesome! 😁👍
Since i reversed my throttle servo on my nitro buggy, servo has no trim fir throttle, all trim is for the brake now...what gives?...idle has to be set with s rewdriver or by hand when starting
This didn’t help at all, mines still won’t go in reverse? Anyone got any links or something that can help?
This is the only way to do it that I'm aware of. Works every time I do it, on multiple GT3B's.
Thanks buddy
I need help
My racestar ESC and motor are going backwards faster
I swapped two wires and now when I press accelerate forward it goes back
You may need to reverse ch2 on your transmitter.
@@RCHobbyShed your a lifesaver it worked
@@h.w.m.306 Glad I could help. 🙂👍
once i change the channel 2 into reverse it automatically accelerate
You may need to adjust your trim setting too. 👍
Nice .problem im having is figureing out how to turn down the throttle on reverse..way to much reverse..Id like it to brake a little longer not slap into reverse..Im running a LRP AI super reverse digital ,its auto no settings .So i have to adjust it on radio.I got good throttle but seems like not enough brake before it goes into reverse..any info i would appreciate.thanks all
Thanks! Hmm, that one I'm not 100% sure about. I think that is more of an ESC issue but since you can't change the setup on your ESC, maybe try turning down the EPA (end point adjustment) on the transmitter. I doubt this will solve the problem, but it may help a little. 👍
@@RCHobbyShed just wanted to share EastSide RC posted some helpful stuff also...and yes the epa did work ,went down to like 70 % on reverse throttle ,it is much better.But yea that esc is wacked..Super reverse ,no joke there..lol
Thanks bro v
Thank ypu!
Thanks this thing is pissing me off I couldn’t figure out why everything was backwards thank you for the video. Lol
It pissed me off too, so I had to make the video lol.
Good to hear it was helpful. 👍
Does this work in nitro
bibi mus Yes it does. 🙂👍
thanx big help lol
Hello i followed the steps but every time i click enter and then go back and turn off the controller it resets
This way works for me. Maybe you can try hitting END to set, as it says in the manual but that doesn't work for me. Good luck!
I was able to figure this out on myself, but for some reason, when I pull on the throttle, the car goes backwards, and when I push the throttle, it goes forwards. This happened both in reverse mode and normal mode. If anyone can help, please lmk. Thx
That's very strange. Are you sure you're reversing the correct channel, (Ch2)? If that doesn't work and you're running a brushless motor, you can try swapping two of the motor wires around. Leave the 3rd wire as is, only swap 2 wires. Hope this helps.
RC Hobby Shed It turns our my second channel wasn’t reversed. Thank you for the help👍
@@chknnuggies That's great, good to know you got it working. 👍
Is there a way to save the setting so you don't have to keep setting it, or is it better to re program the esc
how about the throttle?
At 0:56 channel 2 is throttle
@@RCHobbyShed ohh okay i didn’t catch that. Thank you! 🙏🏽
Man I got this problem I have steering perfect but throttle is reverse
does not work not sure why
Sorry for my slow reply. Hope you got your channels reversed OK. This is the only way I know how to do it and it works for me every time.
🤦..thanks bud
No probs mate! 👍
Thank you!!