Hey I swapped out my K2.0z2 from my 2010 Acura csx with an Acura TSX K2.4A2 engine it still have the OEM ECM can I remap the ECM with the MPP V 16 & will it work
I have a question about getting the MPPS to read the PCM/ECU on a 02 ALH jetta. I'm running windows 10 and followed the install videos on others channels. Loaded the cable drivers and so on. I can't get this thing to I'd or read the PCM. It will start to then pop up the message to remove f11 I then click yes then after about 2 or 3 minutes it errors and says send log files to a email. The percentage doesn't go over 0%. I've tried reading the PCM through the odb2 plug and using a bench flashing set up. I know the PCM is good as the car runs and drives and vcds will connect and talk in both connections setups. This is driving me nuts I've even tried using a virtual Windows 7 machine. Same failure. Any help would be greatly appreciated.
@@ERAutomotive yes. It does the same thing when it's on the bench flash connector completely removed from the car. That's just power ground and comms. Voltage is set around 12.8-13v on the bench flash station. I've tried my spare golf PCM and same thing. Replaced the cable multiple times figured cheap china cable. I only thing I haven't tried is the laptop itself. Don't have another one to try 😂😂
@@ERAutomotive I have no idea 😂. I need to change my MAP to a 4 bar and of course the guy I used to tune the PCM before is no longer doing the "Old Stuff" anymore and with the big crack down here I'm stuck figuring it out myself 😂
Hello. I have a question. I have a Peugeot 207 1.4 8v Flex, with ECU Bosch 7.4.9. I have it's map file and now after remapping it's file with a professional guy, want to know that MPPS can write this Remap file on my ecu with OBD2? Thanks
How did you know that you need V13 cable? Because there are many different mpps out there. Moreover, this software you re showing in the video, do you receive it boundled when you buy the cable?
in the listing there should list the comparable ecus/ vehicles but i knew from an outside source that v13 would work for my needs and yes the software comes with the cable
my car has edc15vm i’ve read the file that was on it and it was tuned. i’ve since edited the file and flashed it onto the car again and it has bricked the ecu… stable voltage with charger hooked up and flashed on with no issues according to mpps went to start and it wouldn’t so tried reading and says no reply from ecu. scanned snap on and vcds all say ecu no comms… apparently it is something to do with checksums? not 100% but any help be appreciated buddy awaiting bench cables to do a recovery
Yes definitely need to verify checksums before flash everytime Some tuners make it so u can’t edit their files so that could be issue as well Depending who tuned it
@@ERAutomotive will it still flash if i put my tweaked file back on for i accidentally edited my orig file that i flashed that bricked it but if i boot mode and flash that file it should work?
Good day! Tell me please, as I understand it, after reading the firmware, the firmware is not deleted from the block, in fact, reading the firmware is like a copy of the original firmware to the computer, so that if necessary, you can return to the native firmware, right? And when you upload a new firmware, the new one is written over the one that is installed in the block, right? And you can always go back to your native firmware. Tell me where to get these firmware?
Mpps does for some Pcmtuner Is cracked pcmflash There’s much newer then the 1.21 u have But depending what ecu ur working with It might do checksum for the file
@@ERAutomotive How do I know if my MPPS will correct checksum? I have V16 clone. It can read ok. Do you know any free or cheap software which can correct checksums on EDC16U1?
i got it from eBay one like this one www.ebay.com/itm/New-OBDII-MPPS-V13-Chip-Tuning-Flash-Car-Diagnostic-Cable/133035597315?hash=item1ef98a1e03:g:1IsAAOSweD5cxTEf
There’s lots of tuning groups on fb and people there offer file service The communication error is prob from when u were flashing Clear and see if it comes back is what I would do
ER Automotive I have a 1.8T passat with a ME7.5 Bosh ECU I select it and it goes no external voltage when I had a charger in also it showed in red 0 volts
hi just got a clone mpps v18 cable and installed and updated drivers as instructed but when i click ecu id it says ecu not found or something like that what could it be?
Recently my laptop crapped out about 5% into loading the new map. Turning the ignition key did nothing, No start. I re-flashed with MPPS the same file a 2nd time and it uploaded successfully. Longest 4 minutes of my life!
good afternoon! please tell me where can i find firmware for the motor? I have a golf 4 TDI injection pump 90 hp. I want to add a little power. I bought an MPPS V13.02 cord, but I don't know where to get the firmware ...
![Чип Тюнинг [ Прошивка ЭБУ ] Знакомство с MPPS V18 на примере Bosch MEDG 17.9.8 BSL / Инструкция](http://i.ytimg.com/vi/Wak3d-gT4mg/mqdefault.jpg)
Mpps has transformed my built mini into a monstrous mini
Can this work with Mazda cx-7 2.3 turbo?
Thankyou very much for the explanation. I am getting my tune from black smoke racing
Excellent information sir! Thank you.
Where did you find flashes for your car or did you buy them and if you did it yourself what software did you use
There’s lots of tuners out there that will do files for you
@Topgear tuning Croatia is one option I have used
Hey I swapped out my K2.0z2 from my 2010 Acura csx with an Acura TSX K2.4A2 engine it still have the OEM ECM can I remap the ECM with the MPP V 16 & will it work
I’ve only done vag cars
You would have to see if your car is on the list
For that cable
Are you extracting the program from the rom to program the hall computer again?
So if you end up bricking your ecu, is it possible to restore it with the original firmware file?
Depends on the ecu
Some require opening and other tools to recover
@@ERAutomotive okay, thank you!
@@ERAutomotive so i was tryne read the ecu and it bricked it how could i even go about fixed it a bench flash and reset?
Out of mpps v13. V16. V18 which would you use?
I’m currently using 13
Haven’t tried the others
But it depends what ecu you are doing
does this work for bmw f10 550i N63 engine?
I’m not sure I’ve
Never tuned any bmw
I have a question about getting the MPPS to read the PCM/ECU on a 02 ALH jetta. I'm running windows 10 and followed the install videos on others channels. Loaded the cable drivers and so on. I can't get this thing to I'd or read the PCM. It will start to then pop up the message to remove f11 I then click yes then after about 2 or 3 minutes it errors and says send log files to a email. The percentage doesn't go over 0%. I've tried reading the PCM through the odb2 plug and using a bench flashing set up. I know the PCM is good as the car runs and drives and vcds will connect and talk in both connections setups. This is driving me nuts I've even tried using a virtual Windows 7 machine. Same failure. Any help would be greatly appreciated.
Are you sure you pulled right fuse
If I recal it’s a 5amp
And your cluster should power off with fuse pulled
@@ERAutomotive yes. It does the same thing when it's on the bench flash connector completely removed from the car. That's just power ground and comms. Voltage is set around 12.8-13v on the bench flash station. I've tried my spare golf PCM and same thing. Replaced the cable multiple times figured cheap china cable. I only thing I haven't tried is the laptop itself. Don't have another one to try 😂😂
Gotta be driver issue or something
I’m on windows 7
Or xp in the past
@@ERAutomotive I have no idea 😂. I need to change my MAP to a 4 bar and of course the guy I used to tune the PCM before is no longer doing the "Old Stuff" anymore and with the big crack down here I'm stuck figuring it out myself 😂
Oh dam
Sorry I’m not familiar with getting it to work on win 10
Do you have too mess with checksums if you read and write straight too car
Always a good idea to verify checksums b4 writing
@@ERAutomotive can you do this with mpps i got it on order just need know if i need anything else
@@markshone4606 depends which ecu
Some mpps can some it doesn’t
@@ERAutomotive me7.5 and ordered latest mpps
Believe it does checksum on me7
And I’ve heard issues with v21
Apparently 18 more stable I have 13
Can i remap my ford fiesta 1.4. 2014 ? And what software to edit my car file?
Hello. I have a question. I have a Peugeot 207 1.4 8v Flex, with ECU Bosch 7.4.9. I have it's map file and now after remapping it's file with a professional guy, want to know that MPPS can write this Remap file on my ecu with OBD2? Thanks
Hi sorry I have no experience with that vehicle so I can’t say
@@ERAutomotive just tell me something, MPPS has ecu automatic recognizing option? Or just can work on Cars that has in it's list?
Just from list
Personally I’d ask your tuner for their experience with it
@@ERAutomotive thanks. So it can't. Brasil use uncommon ecu for peugeot and this is our problem for remap. Thanks
Best of luck going forward
Can I use a OBD cable with the ftdi chip in it with this software?
No you need the cable that matches the software.
Question: where can I get files (tuned/remapped) for my vehicle?
Thanks!
programmed individually under the car
does mpps v16 have an automatic checksum or do I have to do it somehow through another program and when myself through what?
Mpps has checksums for some ecus not all
Will depend on which ecu
Winols will correct checksum for you
@@ERAutomotive thanks
How did you know that you need V13 cable? Because there are many different mpps out there.
Moreover, this software you re showing in the video, do you receive it boundled when you buy the cable?
in the listing there should list the comparable ecus/ vehicles but i knew from an outside source that v13 would work for my needs
and yes the software comes with the cable
my car has edc15vm i’ve read the file that was on it and it was tuned. i’ve since edited the file and flashed it onto the car again and it has bricked the ecu… stable voltage with charger hooked up and flashed on with no issues according to mpps went to start and it wouldn’t so tried reading and says no reply from ecu. scanned snap on and vcds all say ecu no comms… apparently it is something to do with checksums? not 100% but any help be appreciated buddy awaiting bench cables to do a recovery
Yes definitely need to verify checksums before flash everytime
Some tuners make it so u can’t edit their files so that could be issue as well
Depending who tuned it
@@ERAutomotive i’ve no reply from ecu now do i need to put it into boot mode and earth pin 24 on chip or what would be an easier route
Yes will need boot mode
@@ERAutomotive will it still flash if i put my tweaked file back on for i accidentally edited my orig file that i flashed that bricked it but if i boot mode and flash that file it should work?
Personally I would flash back original file and see
Good day! Tell me please, as I understand it, after reading the firmware, the firmware is not deleted from the block, in fact, reading the firmware is like a copy of the original firmware to the computer, so that if necessary, you can return to the native firmware, right?
And when you upload a new firmware, the new one is written over the one that is installed in the block, right? And you can always go back to your native firmware. Tell me where to get these firmware?
Yes that’s correct
@@ERAutomotive Thank you
@@ERAutomotive
Write me your email, or write me an email
roma9009@mail.ru or to Viber +37368015690 and I'll send you my engine firmware to your mail.
I don’t make tunes sorry
Did you use checksums?
Always correct checksums before flashing
Either with mpps or your editing software
@ER Automotive does mpps come with checksums? Or pcmtuner? I seen they offered it on winols tuned files
Mpps does for some
Pcmtuner
Is cracked pcmflash
There’s much newer then the 1.21 u have
But depending what ecu ur working with
It might do checksum for the file
@@ERAutomotive
How do I know if my MPPS will correct checksum? I have V16 clone. It can read ok.
Do you know any free or cheap software which can correct checksums on EDC16U1?
Does it program all modules
Just ecus
CAN U HELP ME READ MY ECU ON MY MK4 Jetta GLI Jetta
will this work on windows 10
Bonjour les amis ,je cherche une âme charitable pour un fichier dinstallatoin pour mon mpps que jai mais qui ne veux plus se lancer svp
What programme do u use is it windows xp?
Hi yes computer is running Windows XP and the program for flashing is mpps it comes with the mpps cable.
@@ERAutomotive yeah flashed before with the programme was just on windows 8 before tho
Oh right on yeah it’s a pretty good tool and straight forward to use
How to download software the ecu stage 1 ??
Find a tuner to make u a stage one file from your original read
Did you have the link where you get the cable from sir ?
i got it from eBay
one like this one
www.ebay.com/itm/New-OBDII-MPPS-V13-Chip-Tuning-Flash-Car-Diagnostic-Cable/133035597315?hash=item1ef98a1e03:g:1IsAAOSweD5cxTEf
Hello sir, you used original MPPS license or a clone? What if my car is not in the list, any advice?
If your car isn’t on the list. Then you’ll be looking for another tool
That is compatible with your ecu
@@ERAutomotive ouh sad, it will make me spend more money. ehm, can i choose "Generic" from select make tab?
I have no experience with that sorry
@@ERAutomotive okay thanks for your response, I appreciate it
Where to get good files from I have mpps v16 and I revamped my car now its saying no communications with transmision
There’s lots of tuning groups on fb and people there offer file service
The communication error is prob from when u were flashing
Clear and see if it comes back is what I would do
Does it already have the tune
U have to get the tune for your specific vehicle
Will is work on a b7 a4
Risky on that ecu with a cheap mpps cable
@@ERAutomotivebut will it work
It might work
It might brick the ecu
Personally I would suggest Ktag
hello sir what if my car model is not on the MPPS program ? can i still remap ?
Then it’s not supported by mpps
What car?
Hello, how do I know which control unit I have?
Best bet is to pull the ecu and check
Hi I forget to switch off and on key for last reading steps ... is is a problem ?
I’ve never done it. Does it start??
@@ERAutomotive yes start without problems ;)
Perfect!!
I keep getting a checksum error no response from ECU at 70% read any ideas on why
Which ecu
@@ERAutomotive 2001 VW new beetle 1.9 TDI Bosch EDC15
That’s strange I’ve done a ton of those without issues
Did u pull the dash fuse?
@@ERAutomotive if I pull the dash fuse I have no communication at all with the ecu unless I’m pulling the wrong fuse I was told to pull fuse 11
That’s strange
I’m sorry I don’t know what to say
Never had issues with those ecus
I can't even get to the screen to load I been trying to figure it out
Mine isn't reading any voltage, do you know a fix?
Does it Id the ecu? Are you sure you have all the wires correctly for you specific ecu. Yours might be different then the examples in the video
ER Automotive I have a 1.8T passat with a ME7.5 Bosh ECU I select it and it goes no external voltage when I had a charger in also it showed in red 0 volts
Are you sure all the wires are correct? Can u communicate with a scan tool?
ER Automotive it plugs into my computer and it says amtflash
Did u make the bench harness?? Are you sure it’s wired correctly ?
Where did you get this software ?
Comes with the hardware when purchased
hi just got a clone mpps v18 cable and installed and updated drivers as instructed but when i click ecu id it says ecu not found or something like that what could it be?
Are u sure u selected the right protocol
What would one person do if they brick the computer?
Depends on which computer depends the recovery method
Recently my laptop crapped out about 5% into loading the new map. Turning the ignition key did nothing, No start. I re-flashed with MPPS the same file a 2nd time and it uploaded successfully. Longest 4 minutes of my life!
Yeah scary times
Gotta have a reliable laptop plugged in and car on charger as well
Hey sir so I have a question where are you getting your tune file at? Like how are you getting the map to program into the ecu?
i got from a local tuner
there are other tuners who with send u files to load on
Can u make video, how to remove ews in DME ME7.2? I have some definitions, but I don't know how to do. 😃😃
good afternoon! please tell me where can i find firmware for the motor? I have a golf 4 TDI injection pump 90 hp. I want to add a little power. I bought an MPPS V13.02 cord, but I don't know where to get the firmware ...
Contact a tuner and purchase a tune
You’ll read the file off your car and send it to theM and they will send u back modified file
@@ERAutomotive Nevertheless, thank you for the video! Everything was explained very well!
Who does the writing of the software tunes?
Depends on the car you have
There are lots of tuners who offer file service on Facebook tuning groups