You are totaly right. The friction lock of a important part (bolt) is no safe solution. Its so unbelieveable that they refuse to deliver a Safe answer for this.
I solved that problem by reducing a little material from the upper, where the metal stables has contact to the upper. So it presses slidely on the takedown pin.
@arandomkiwi1110 if you disasamble the holding parts of the takedown pin by unscrew that single screw on the downside of the upper, there comes out that "u" shaped piece of metal. That is what I mean.
18:55 Curious. I had the exact same problem. They have sent me a completely twisted 150 lbs limb. After returning it on my own expenses, they have sent me a replacement with a defective lamination. It's like they either have no sufficient quality control, or just don't care about customer safety - or both.
I’ve had three quality issues with Steambow products that I bought directly from them. I never sent anything back-they always told me to keep it. These guys almost had me hoping they send me something defective so I can get free bolts or a free string. I'm not even joking. 🤣
I just have the same issue. Could not shoot more than 20 times until the upper opened up. Damn dangerous. Sometims the bolts jam on the loaded M10. Steambow refused to provide a solution when I contacted them. I had to purchase a 3d printed 3rd party bolt that locks safe. I will never purchase any steambow product again. Thats a safety hazard.
Do you have an external platform or mail address to communicate? I could send you the solution, even to the magazine problem (bolts falling out etc.), but I can't post it here.
I have Steambow M10. It never does that to me. I shook it hard that the pin doesn’t come out. I would have to pull to top receiver toward me a little bit while holding to pull the pin out.
I'm happy to hear that! I still recommend asking Steambow about this new block. It definitely has more friction. If you don't like it, you can always go back to the old block. However, this happened to me, and it scared the ***** out of me. It does happen to others too-otherwise, there wouldn't be a need for a solution.
Mine you can’t pull the pin out easily. Like I say I have to pull back toward me to loosen up to pull the pin. Maybe it is different in USA then over there?
![เปิดบ้าน โคตรสวย ป๋องกพล รู้จักตั้งนาน เพิ่งรู้ว่ารวย!!! l [Nickynachat]](http://i.ytimg.com/vi/tmgCF_2HfYI/mqdefault.jpg)
Do you have a solution? Let me know! If it works and is safe, I’ll do a review about them.
You are totaly right. The friction lock of a important part (bolt) is no safe solution. Its so unbelieveable that they refuse to deliver a Safe answer for this.
I solved that problem by reducing a little material from the upper, where the metal stables has contact to the upper. So it presses slidely on the takedown pin.
Thanks for the tip, but what do you mean by "where the metal stables has contact to the upper" ?
@arandomkiwi1110 if you disasamble the holding parts of the takedown pin by unscrew that single screw on the downside of the upper, there comes out that "u" shaped piece of metal. That is what I mean.
@@user-dx7po2yk3u Thanks 👍
18:55 Curious. I had the exact same problem. They have sent me a completely twisted 150 lbs limb.
After returning it on my own expenses, they have sent me a replacement with a defective lamination.
It's like they either have no sufficient quality control, or just don't care about customer safety - or both.
I think they don‘t have a quality control.
I’ve had three quality issues with Steambow products that I bought directly from them. I never sent anything back-they always told me to keep it. These guys almost had me hoping they send me something defective so I can get free bolts or a free string. I'm not even joking. 🤣
I just have the same issue. Could not shoot more than 20 times until the upper opened up. Damn dangerous. Sometims the bolts jam on the loaded M10. Steambow refused to provide a solution when I contacted them. I had to purchase a 3d printed 3rd party bolt that locks safe. I will never purchase any steambow product again. Thats a safety hazard.
Mag ik vragen waar jij je losse magazijnen haalt
Do you have an external platform or mail address to communicate?
I could send you the solution, even to the magazine problem (bolts falling out etc.), but I can't post it here.
@5PL45H0R Not yet, though. I’m interested to hear more about this. I’ll figure something out and get back to you.
@@Dutch_Defense_and_Survival Ok, nice.
I have Steambow M10. It never does that to me. I shook it hard that the pin doesn’t come out. I would have to pull to top receiver toward me a little bit while holding to pull the pin out.
I'm happy to hear that! I still recommend asking Steambow about this new block. It definitely has more friction. If you don't like it, you can always go back to the old block. However, this happened to me, and it scared the ***** out of me. It does happen to others too-otherwise, there wouldn't be a need for a solution.
Mine you can’t pull the pin out easily. Like I say I have to pull back toward me to loosen up to pull the pin. Maybe it is different in USA then over there?