@ Magnum-Technical Academy 1.there is no demonstration on how to connect it to a gen set 2. can it automatically off/On A GEN set 3 what the max amp it can handle 4. assuming you want to upgrade the amp it handle how can one do that
You're good Mr Magnum . Can the switching time (5s, 10s, and 15s) be reduced to a smallest possible value ? so as to increase switching speed and reduce delay .
Can switching be achieved without ever interrupting the supply to the load(The CFL lamp as used in your video) ? Bypassing power interruption to load .
hello, I had written to you before, I don't know where I could contact you better, but as an improvement you could use a 12 volt capacitive source because it is only to power the passive components, and one question, do you have the PDSPRJ file, can you provide me or send me? . All the best
Good evening.... great work,I was given this as a project,do I need to build it using Arduino and please can you list out all components and devices used
Thank you very much for nice project, I would just like to know on the polatity of transistor how the pins are arranged the drain, source and the gate?
Ok, I guess you should check for the Circuit diagram, which we presented. It should guild you on the connection. The link for the Circuit is on the video description
Great explaination and good demonstration for the System
😲
Thanks for the video
I appreciate your kind feedback 😊
Good work.....
That's impressive.
Where can I get the board ??? And also can we get a circuit diagram
Check the video description for the project design information
Well done
Thanks 😊 I appreciate
@
Magnum-Technical Academy
1.there is no demonstration on how to connect it to a gen set
2. can it automatically off/On A GEN set
3 what the max amp it can handle
4. assuming you want to upgrade the amp it handle how can one do that
Sure all these features are highly feasible for the project
You're good Mr Magnum .
Can the switching time (5s, 10s, and 15s) be reduced to a smallest possible value ?
so as to increase switching speed and reduce delay .
Sure by changing the discharge resistor
Can switching be achieved without ever interrupting the supply to the load(The CFL lamp as used in your video) ?
Bypassing power interruption to load .
Yes, the switching is made without interruption
But,the lamp goes off whenever you diconnect the current active phase ...
It is good project but it is taking time to switch 5sec why ....
Ensure your connection are quite correct
how to get circuit of your projecttt
Check the video description
good work sir. but i only see 3 relays in the diagram. in the video i see more than 3 relay. can u tell me why
The two are for generator switching
can u give me the diagram for the generator switch
Allah (GOD) Bless you for this project and for sharing the project!
Thanks 😊 I appreciate your kind feedback
any component calculations?
Check the PDF file on the description
@@MagnumTechnicalAcademy thanks
can i have the diagram connection for generator switch
It added to the video description
Bad lighting
Sure, I will take care of that
Great work sir. Can we please 🙏 have a private conversation sir.
sir what is the use by fixing this in any places like home or somewhere?
hello, I had written to you before, I don't know where I could contact you better, but as an improvement you could use a 12 volt capacitive source because it is only to power the passive components, and one question, do you have the PDSPRJ file, can you provide me or send me? .
All the best
Good evening.... great work,I was given this as a project,do I need to build it using Arduino and please can you list out all components and devices used
Sure we will love to be of to you, as I can tell you are from Nigeria...
This is our WhatsApp number, send us, and we will assist you!
+2348096283289
Thank you very much for nice project, I would just like to know on the polatity of transistor how the pins are arranged the drain, source and the gate?
Ok, I guess you should check for the Circuit diagram, which we presented. It should guild you on the connection. The link for the Circuit is on the video description
Thank u sir, but how can this be achieved with only one transformer is it possible?
Using one transformer won't be possible, as the system is built for 3 phase and hence 3 seperate transformer
Nice project
Good work bro
It is a good project! But mr the instructable link is leading to 3 audio channel mixer project and not this project!
So sorry about that, we are yet to publish the instructibles...
@@MagnumTechnicalAcademy see u at the top!
Hallo good project keep it up bro
Thanks 😊 I appreciate your feedback
Nice work
Thanks 😊 I appreciate
this is a very nice project. the final construction shows a digital display where is its signal being tapped from in the circuit
Thanks for the feedback
@@MagnumTechnicalAcademy welcome sir, is it possible for you to send me a simulation file of the same in electronic workbench, or proteus?
@@marshalldaka7081 the link to the simulation is dropped on the video description
@@MagnumTechnicalAcademy how about the 5s, 10s, 15s Which part of the circuit determines them?
@@marshalldaka7081 the resistor connected to pin 2 of the 555 timer IC