How to set up a DBX Driverack PA audio processor
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2024
- some of my technicians have been asking for some training on how to set up a Driverack so I videoed it while I showed them. This just covers the basics but you should be able to get going with this video.
just got one of these for a gift. got brain blocked when i seen the three outputs and other videos explaining how to set up. this video crushed it and now can add some old yamaha dual subs/tops and crown amps with a crossover from the dbx to my existing smaller qsc setup. six subs instead of just two is going to be fun. thank you!!
this video saved my ass as i didnt know where to even start. thank you
08:08 EQ ,9:03 Com, 6:21 gain control, 10:03 Adjusting Threshold, 11:50 Limiter Setting
Honestly I just plug in and hope it does its job. Luckily there's videos like this that helps understand more this product.
If you have bass reflex woofers and can see the woofers, run test tones through them at medium volume and sweep down until tuning (you should see the cone move less and less) and then below tuning you will see it move more. For instance if your subwoofer is tuned to 35Hz, you will see the cone motion reduced at that frequency, then you can set your high pass at around 33.5Hz setting (you can get away with going a bit below tuning because the roll off of the processor should exceed the increased motion of the subwoofers). You should use the BW (Butterworth) 24 (dB/Octave attenuation) or LR (Linkwitz-Riley) 24 settings to high pass subwoofers. Live mics run full range and turntables are the main culprits for sending lots of damagingly low frequencies to subwoofers, that and someone requesting "Bass I Love You" at a DJ set.
You can do the same with your mid-highs although setting the high pass slightly above the tuning will make it easier to match the phase of the subwoofers and tops. E.g. if the tuning of your top cabs is 80Hz, maybe 90Hz or so crossover.
On my Subwoofers I would set the limiter if I had an amplifier bigger than my Peavey IPR1600 with DDT compression built in. The amplifier does seem to be matched well to about the maximum I would be comfortable taking my 12 subwoofers.
Thanks, Dude! This video was a tremendous help and tutorial. I've had my Driver Rack PA+ since 2012 and never really had it set up to suit my taste. I recently bought a Crown amplifier that wasn't listed in the presets, which forced me to manually dial in my settings. Before finding this video, I decided to do a factory hard reset and start from scratch. This video took me through the important steps and the results sound better than it ever did! Thanks for the time you took making this video! Great work and much appreciated!
Great video. Planning to get one and this really helped.
Nice video for this gear. Thanks for taking the time to share.
Very informative video really helps with information to break it down when dbx did the tutorial on this it was known as clear as what you put out thanks for all your help
thanks bro for this video God bless u
So informative great video absolutely professional.
Great Video. It really helped me a lot! Thank You
Very useful - just inherited one of these in new church
Great video but you have seriously missed the best trick this bit of equipment has. The auto EQ using the Dbx,s RTA mic. It’s turned some of my good PA systems into something that sounds incredible. Each to there own I guess.
🤯 Dude, great job ... got it!!
The knowledge was helpful thanks alot
I noticed there was no separate sub level control on this driverack PA like the Behringer had. This driverack pa definitely sounds better and it looks like I can use the eq control for sub level on the fly ty.
thanks for sharing your video
Very clear. Thanks a ton. 👍
Thanks for this mate!
Great video, total pro
Really helpful! Thank you!
thank you itbeing really helpful i need to lean more jus but my dbx drivepack 260
The imput switch is in +4 or -10 position? How is more corect? Thnks
How can I go back to my previous channels that has been stored.
Very helpful could you do a video on the dsp you have above the dbx
The Professional Couriers
Great
Bro need more information about limiter parameters for professional speakers
Terima kasih.
Hi sir! I have powered speakers(ALTO) is there any problem if i choose BIAMP in main speaker selection?
Just bought someone's Alto set: 2 x TS115A & TS SUB18. Looking at a processor, maybe this one. Did you manage to get the settings right? thank you.
@@hettovennik2887 yes ive got driverack pa2 there is a manual copy how to set up with active speakers :)
How dbx work with single speaker with left and right
Nice
Thank you for the assist I could not figure out. I am still confused about the BW. I'm trying to get a tight thump from my subs and a pristine clarity from my full range I stumble on a setting for the highs but the bass is still soft and without impact can you suggest the appropriate setting ?
Dope vid !!!
How that work with other crossover different frequency
Thank You Good Video .. !!!
I’m not getting any bass on my end. Any idea how to raise just the volume
Can do your own settings then build in one
love this vid
Do you have sort it each time on it on
I gotta play with the low the new JBL EON618s goes down to 30Hz so do I roll it to 30 or start the butterworth at 30 hz? I think it should be cleaner if I roll to 30hz but will test.
How use both power and pa
Did you remember to check for any possible signs of trouble in one and two?
1200wpowerspeaker and 1500w amplifier
Hey very useful but wats the best frequency for a peavey 44xt horn
Thanks man.
If im using a powered speaker like the EV elx series would i choose passive or bi amp?? Thanks
What about 80hz speaker
Great video just one question will this driverack work with power speakers. I bought the Driverack 260 with out knowing it if does work ?
yes it will.
Just plug the XLR cable from the high output(s) into each powered "cab on stick", and if you have active subwoofers link from the XLR low outputs into the input of each subwoofer.
If you are running two or more close together mono subwoofers or more than one per side stereo subwoofers you can daisy chain from the XLR out of one subwoofer into another.
You may need to do some matching of input sensitivities on the powered cabs.
I'm looking into the dbx driverack pa2 but every time I watch a video I understand less on how to set this up with my active speakers with no subs.
Can it be update with different speakers
question....can you use this for studio recording?
Can produce zero bass freq.?
Anything on the pink noise and mic?
Hey does it like a feedback supression?
Speaker use crossover network 2 different crossover
Has it got freeback
Thanks, instruction booklet is not helpful, however your explanation is great! It should help with the "clean up the sound" problem.....I did see the word "clipping" show up on the main display, I only had the main vol on the master mixer not even up to nominal and the driverack was clipping.....as I pulled down the master, at about 3db lower, the clipping dissipated, and the sound was great without all that shitty distortion. Thanks for tips for setting the perimeters on the comp/limiters....very nice explanation.
You forgot one thing gains are not volume
Midland Atlantic Television will soon be on and running with brand new eye popping contents... Watch out.
Je vé la version française
Sai pancham sounds
Mukesh
Dark like in theater, cant see a thing
Peut soutenir le vietnamien n'est pas