Tôi cũng làm với máy mazak integrex i200 được vài năm và tôi cũng thực sự yêu thích công việc này giống như bạn…mỗi khi làm xong 1 sản phẩm phức tạp tôi thấy rất vui
Bro, do you buy your aluminum alloy material offline or online, I need an online platform to buy aluminum alloy material very much, looking forward to your reply.
Considering that the doors do not open, we can assume that this is a machine with automatic cutter replacement. I think that this is excessive automation, because it is not difficult for the machine operator to change cutters and before installing them, for high-quality operation of the machine, he must check the integrity of the cutter. And the program was also written incorrectly: when removing several centimeters of metal, it is necessary to turn on the cooling to avoid overheating the cutter and putting it out of order. In other cases, it was possible to reduce the cooling pressure, but this is not necessary, because this only slightly increases the energy consumption of the machine and does not affect the quality of the part or durability of the cutter
Normal not all pieces need 5 axis, in my workplace 70% of the time i just use 3 axis and even the rest most of the times i dont even use the full capabilities most of the tollpaths dont even need continuous 5 axis. with the rigth tolls you can cut the necessity to use all 5axis and if you use them you sacrifice rigidity...
Why…? When speeds and feeds are good, it sounds good. It’s a damn orchestra as they say. This however, had very few good sounding tool paths, so why bother knowing the bad feeds and speeds? I can’t force myself to finish this vid. Sorry! I’m out.
Если учесть что двери не открываются, то можно предположить что это станок с автоматической заменой фрезы. Я думаю что это излишняя автоматизация, потому что оператору станка не сложно менять фрезы и перед их установкой для качественной работы станка он должен проверять целостность фрезы. И программа тоже была написана неправильно: при съеме нескольких сантиметров металла надо обязательно включать охлаждение чтоб избежать перегрева фрезы и вывода ее из строя. В остальных случаях можно было уменьшить напор охлаждения, но это не обязательно, потому что это только немного увеличивает энергопотребление станка и не влияет на качество выполнения детали или время износа фрезы
Typical "demo" big hunk of steel in an ideal clamping. Lots of extraneous metal removal making a useless paperweight. Overly big retractions and R planes.
It’s definitely aluminum. Ran lots of parts like this as a weld tooling designer. Sometimes starting with a well clamped piece even if you have to rough a lot of it off just makes it faster and when you’ve got more work than spindles it helps. Had this discussion with lots of people who never touched a cnc controller.
@@loganjetton6134 AS senior manufacturing engineer and programmer at PBR (corvette Z06 calipers etc.) Once the biggest Okuma site in the southern hemisphere and over 100 cnc in one plant alone (various Mazak Fanuc Mitsubishi Heidenhahn Matsuura Siemens etc.) we rationalised down to a single machine supplier Chiron FZ22w with 840D. Merely stating that this is a typical demo with ideal conditions producing a paperweight..
Agreed ... In my shop we use a band saw or even a chop saw to take out the overage ... Oh and we don't use the 5-axis for anything under a 4-axis job ... That would have gone in our HAAS or if it needed the rpm's the robodrill ...
I love watching circ interp work at high speeds and feeds.
Programmed and ran the Hermle. One of the finest 5 axis machines. I think God has one in his shop.
You clearly haven't run a DMG MORI 5 Axis
I have run a DMU 40 for about 2000 hours. When I had the opportunity to purchase a 5 axis I selected the Hermle based on that experience.
I worked on cnc mills for a few years this video is friggin awesome! I miss that shit. Amazing machines
Tôi cũng làm với máy mazak integrex i200 được vài năm và tôi cũng thực sự yêu thích công việc này giống như bạn…mỗi khi làm xong 1 sản phẩm phức tạp tôi thấy rất vui
If I had one of these in my house, my shoes, sunglasses and hat would all be made out of CNC metal for real.
You can watch this without stopping.
This is my world ❤❤❤❤
When roughing use cycle 32 for tolerance
most beautifull of machines in the world... not the best of CAM...but it got the job done.
Essa máquina e incrível 👍👍
Bro, do you buy your aluminum alloy material offline or online, I need an online platform to buy aluminum alloy material very much, looking forward to your reply.
Image clickbait..
就是我们这边说的:标题党
Does hermle have an accuracy selection gcode like the haas mills do? G187 p1-3. Seems choppy during the adaptive is all
Considering that the doors do not open, we can assume that this is a machine with automatic cutter replacement.
I think that this is excessive automation, because it is not difficult for the machine operator to change cutters and before installing them, for high-quality operation of the machine, he must check the integrity of the cutter.
And the program was also written incorrectly: when removing several centimeters of metal, it is necessary to turn on the cooling to avoid overheating the cutter and putting it out of order. In other cases, it was possible to reduce the cooling pressure, but this is not necessary, because this only slightly increases the energy consumption of the machine and does not affect the quality of the part or durability of the cutter
Not one five axis move. All 3 +2
Normal not all pieces need 5 axis, in my workplace 70% of the time i just use 3 axis and even the rest most of the times i dont even use the full capabilities most of the tollpaths dont even need continuous 5 axis. with the rigth tolls you can cut the necessity to use all 5axis and if you use them you sacrifice rigidity...
What is Variable inspection frequency for machined components in cnc
Looks good, we also have a five-axis machine at our company.
Excellent work!!!
머시닝센터의 비트 절삭 방향이 반대 방향이라야 맞는것 같은데~~~
wouldve been nice if they had included the speeds and feed
Why…?
When speeds and feeds are good, it sounds good. It’s a damn orchestra as they say.
This however, had very few good sounding tool paths, so why bother knowing the bad feeds and speeds? I can’t force myself to finish this vid. Sorry! I’m out.
Where is the rim…as.hol.?
Why plunge mill ant-clockwise
因为加工方向不是根据失真运转方向决定的，而是以刀具在工件的左侧决定的，所以加工外圆是顺时针加工内圆为逆时针，保持刀具在工件的左侧（既为顺铣）
Pls input the programme also
Bangladesh Sherpur districts watching video.
Fin end mill..for roughing? Bravo ..excellent😂😂😂😂 and for finishing ...you use rough end mill...no?😂😂😂
Bad programming could’ve been done in half the time and bad tool choices way too long on lengths
Get your fish and let men work
Если учесть что двери не открываются, то можно предположить что это станок с автоматической заменой фрезы.
Я думаю что это излишняя автоматизация, потому что оператору станка не сложно менять фрезы и перед их установкой для качественной работы станка он должен проверять целостность фрезы.
И программа тоже была написана неправильно: при съеме нескольких сантиметров металла надо обязательно включать охлаждение чтоб избежать перегрева фрезы и вывода ее из строя. В остальных случаях можно было уменьшить напор охлаждения, но это не обязательно, потому что это только немного увеличивает энергопотребление станка и не влияет на качество выполнения детали или время износа фрезы
All I see is 3 + 2 where is the 5x motion at what a big burden
0:46 bruh, come on, lower that Z axis tool a little bit 😅
ВАЗ?
spends all that money on a 5 axis mill but doesnt bother getting thru coolant collets
True
Thay just make color for sell machine 😂
👍👍👍🇮🇩 mantap bosss
Typical "demo" big hunk of steel in an ideal clamping. Lots of extraneous metal removal making a useless paperweight. Overly big retractions and R planes.
It’s definitely aluminum. Ran lots of parts like this as a weld tooling designer. Sometimes starting with a well clamped piece even if you have to rough a lot of it off just makes it faster and when you’ve got more work than spindles it helps. Had this discussion with lots of people who never touched a cnc controller.
@@loganjetton6134 AS senior manufacturing engineer and programmer at PBR (corvette Z06 calipers etc.) Once the biggest Okuma site in the southern hemisphere and over 100 cnc in one plant alone (various Mazak Fanuc Mitsubishi Heidenhahn Matsuura Siemens etc.) we rationalised down to a single machine supplier Chiron FZ22w with 840D. Merely stating that this is a typical demo with ideal conditions producing a paperweight..
Agreed ...
In my shop we use a band saw or even a chop saw to take out the overage ...
Oh and we don't use the 5-axis for anything under a 4-axis job ...
That would have gone in our HAAS or if it needed the rpm's the robodrill ...
Numpang tanya
Rodriguez Karen Hall Maria Hernandez Cynthia
Guardate questo link😂
Jones Robert Harris David Martinez Anthony
''Luftfräsen'' wird hier wohl groß geschrieben.......schlecht programmiert
Bang mau naya
O ug
je mi jasné, že když to chytíš za ten nadměrek tak to zničíš...
👌👌