Lexus is250 stater replacement STEP BY STEP

แชร์
ฝัง
  • เผยแพร่เมื่อ 29 พ.ย. 2024

ความคิดเห็น • 53

  • @ibm_goat
    @ibm_goat 3 หลายเดือนก่อน +5

    My dawg, hell of a video. I’m a tech and I’ve never done a starter on one of these yet. Book time is 3.7 hours so I looked up the procedure on AllData and was not stoked to do the job this morning. Hopped on youtube to find any shortcuts and watched your video. Had it done within 45 minutes. You earned a like and comment my man.

  • @ts8202
    @ts8202 2 ปีที่แล้ว +11

    Great video, this is easily the best one I have found and just used it this weekend to change out my starter. Just a heads up, if you do not want to remove the steering linkage you can loosen the two motor mounts from under the lower A arms and the 4 nuts under the transmission mount. Put a board under you oil pan (2x6x12ish) and use a jack to lift it about 1/8th to 1/4 of an inch, in all it takes less than 5 minutes. This will provide all the clearance you need to get the old started out without removing the steering linkage. Again thank you for making such a detailed video.

  • @worray
    @worray 8 หลายเดือนก่อน +1

    My bottom bolt had stripped AND the connector was broken and previous people who worked on it put silicone so I had to get a new connector. However this tutorial helped a lot, I used the same method, though for the stripped bolt I used bolt extractor, they come in 10-14mm ish which was good enough, however I was able to take out the starter without removing the steering racks, just gotta maneuver enough and patience. Thanks again

  • @Attila-LV
    @Attila-LV 2 ปีที่แล้ว +3

    Thank you for the video. Very helpful. Genuine Lexus starter on order for my 2008 is350 w/ 168k miles. Will be attempting this myself in the very near future.

  • @anthony89764
    @anthony89764 ปีที่แล้ว

    Great video sir it helps me a lot thank you,Just missing the part when you put it back in there the starter electric wire can be plugged into the starter after secured the starter bolts is more easy thank you again for this video is the best on you tube.

  • @tonycastro6154
    @tonycastro6154 ปีที่แล้ว +1

    THANKS A MILLION BROTHER HELPED 10000000000000% PLUS...MAN YOU SOUND LIKE TONE LOKE....

  • @AlbertBustamante-b2q
    @AlbertBustamante-b2q ปีที่แล้ว +1

    Your video was great bro I couldn't of did without it .

  • @jope2123
    @jope2123 25 วันที่ผ่านมา

    Do you think changing the starter will fix P0345/348 Camshaft position sensor codes?? I saw in a forum that a specialist diagnosed that the cause was a faulty starter!??

  • @jeremiahjackson533
    @jeremiahjackson533 2 ปีที่แล้ว +5

    Good job man you walk through the entire job and point it out the sticking points this was a big help the only thing I do different is I take the seat belt and wrap around the steering wheel that keeps the clock spring from turning but overall you nailed it

  • @250-Is
    @250-Is 9 หลายเดือนก่อน +1

    Need help, lol you did your job in an hour but I’m struggling to get my daily up so the bus ain’t helping… so I took off starter, placed new starter in the area, but can’t wobbly the wobble of the starter into the whole where it’s supposed to go, got the battery cable in, and sensor plug in, but it ain’t going in, I think the down pipe has a metal heat shield on it which is blocking my solenoid on the starter from barely making that wobbly of a turn into place, people say awd and rwd are different but dang im sooo close, its my day off when the sun comes up any suggestions? Cuz the ending of your video when you put the cable on was great, i just needed the rest of the footage to help me out 😅😢. It great video 🎉

  • @toyotatundra0455
    @toyotatundra0455 6 หลายเดือนก่อน +1

    Have you replaced the starter in a 2009 AWD Lexus IS250? In my car, the starter is above the engine mount.

  • @Gdjjskx
    @Gdjjskx ปีที่แล้ว +2

    Having trouble with getting the steering shaft back on was it just easier to completely take it off

  • @anthonyespinosa1636
    @anthonyespinosa1636 ปีที่แล้ว

    The best video I ever see thank u save my day 😅😅.

  • @frederickwright259
    @frederickwright259 2 ปีที่แล้ว +1

    Best video i seen very detailed great 👍 job

  • @zemoney954
    @zemoney954 2 ปีที่แล้ว +1

    You da man ! Thanks Brother...keep WRENCHING.

  • @andrewharrison7027
    @andrewharrison7027 2 ปีที่แล้ว +1

    Thank you Your video What's good Finished my car do the Same Why Just don't have the steering rack uk car Thanks🏴󠁧󠁢󠁥󠁮󠁧󠁿

  • @rushadewright3772
    @rushadewright3772 ปีที่แล้ว

    This helped me out today thanks 😊 brother

  • @godsonmatthew6805
    @godsonmatthew6805 2 ปีที่แล้ว +2

    Great job. Is this an AWD or Rear wheel drive?

    • @BryanVukich
      @BryanVukich 2 ปีที่แล้ว +2

      At 2:04 you can see a front axle, so it must be AWD.

    • @Rjj2721
      @Rjj2721 5 หลายเดือนก่อน

      ​@BryanVukich it's rwd buddy. At 12:00 you don't see any cv axle.

  • @zoticus1
    @zoticus1 2 ปีที่แล้ว +1

    Nice job bro, maybe get some cardboard to lay on, or corrugated plastic from signs. Very comfortable

  • @juansantiago4657
    @juansantiago4657 2 ปีที่แล้ว +1

    Unable to get that top bolt off of. Stripped it. Did you use impact gun to remove it?

    • @HayesMobileAutoRepair
      @HayesMobileAutoRepair  2 ปีที่แล้ว

      6 point socket ONLY.. You gotta make sure that the socket is all the way on the bolt so it can’t be crooked

  • @BLACKJACK2432
    @BLACKJACK2432 3 ปีที่แล้ว +1

    Great mechanic

  • @tabiasmclain1140
    @tabiasmclain1140 2 ปีที่แล้ว +1

    Wish u was in SC Because my starter just gone out.

  • @zemoney954
    @zemoney954 2 ปีที่แล้ว +1

    What a job like that run?

  • @Chris_Sokol
    @Chris_Sokol 10 หลายเดือนก่อน +1

    Sadly this will not work for the all-wheel drive version. Have to go from the top, which involves removing several components including the alternator and exhaust manifold.

  • @andrewharrison7027
    @andrewharrison7027 2 ปีที่แล้ว +3

    Did you have to take the engine mount off

  • @janeawashington9416
    @janeawashington9416 ปีที่แล้ว +1

    How to remove it if it’s stripped?

  • @seancaudle1728
    @seancaudle1728 2 ปีที่แล้ว +3

    Bro the best video thank you . This video let me know 1 thing that i wont be replacing the starter myself lol where are you located ?

    • @HayesMobileAutoRepair
      @HayesMobileAutoRepair  2 ปีที่แล้ว

      Lol, it’s not too bad. Follow the vid and u will be fine. Get the right tools. Good luck 👍🏽

  • @ZeZe-pv2gi
    @ZeZe-pv2gi ปีที่แล้ว +1

    Best one. Thank you

  • @yulesh5726
    @yulesh5726 ปีที่แล้ว +1

    Thank you!

  • @305tyrone4
    @305tyrone4 2 ปีที่แล้ว +1

    What year is 250 is this?

  • @supermanclarkkentsr4667
    @supermanclarkkentsr4667 3 ปีที่แล้ว +1

    miss ya big bro

  • @davedaman2798
    @davedaman2798 2 ปีที่แล้ว +1

    I didnt even have to take out the shafts to remove the starter and reinstall it lol

  • @TonyDean6020
    @TonyDean6020 2 ปีที่แล้ว +2

    Was this awd?

    • @HayesMobileAutoRepair
      @HayesMobileAutoRepair  2 ปีที่แล้ว

      Idk 🤷‍♂️ yours is not set up the same or something. Let us know

  • @luis32050
    @luis32050 7 หลายเดือนก่อน

    perfect thank fothe info

  • @agboolanajeem5268
    @agboolanajeem5268 ปีที่แล้ว

    👍👍👍👍

  • @Osbaldoownz
    @Osbaldoownz 2 ปีที่แล้ว +2

    I just stripped the top bolt 🤦🏻‍♂️

    • @HayesMobileAutoRepair
      @HayesMobileAutoRepair  2 ปีที่แล้ว +1

      NOOOOOO! That’s sucks. Hope you were using a 6 point socket😬

    • @juansantiago4657
      @juansantiago4657 2 ปีที่แล้ว

      @@HayesMobileAutoRepair 14mm ??

    • @juansantiago4657
      @juansantiago4657 2 ปีที่แล้ว +1

      What did you end up doing to remove stripped bolt?

  • @BLACKJACK2432
    @BLACKJACK2432 3 ปีที่แล้ว +3

    Great mechanic