How To Get Into Diagnostic Mode On Whirlpool & Amana Washing Machines & Test Washer
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- Honest To Goodness Appliance shows you how to get into diagnostic mode on Whirlpool top load washing machine. This video demonstrates how to test every component of your Whirlpool or Amana Washing machine. We test the lid lock, hot and cold water valve, drain pump, agitation, and spin cycle. We also shoe you how to calibrate your Whirlpool washer. Thanks for watching, and if you're in the San Marcos area, reach out to us for service. htgappliance.com
This video saved us a lot of time and money. We were able to follow the easy steps to diagnose the actuator needed to be changed, had the part ordered changed and re-calibrated in a day. Thank you very much for the easy but thorough video!
What part did you have to get for the actuator? Please 🙏🏽
Best, actually informative video I've seen. After getting it to do an actual wash, I went to wash my bathmat next, so put the machine on delicate. It filled the water enough to submerge it, then immediately drained. It did the same thing for rinse. ZERO agatation between filling and draining. That's not how a delicate cycle is supposed to work, is it? At least it spun. LOL This thing is junk as far as the programming goes. I wish I could afford a Samsung, which has way more 5 star ratings than any Whirlpool-made machine.
Great info, thanks
Excellent viseo instruction! Many many thanks to you. Although I am retired from years of production machine trouble shooting and repair & maintenance, the service manual I received with this washer just hurt my analog brain.
Great thanks for information
Also when I’m doing the diagnostic should my controller line up with what you did in the video. The lights did but when you might be on the regular my knob is on drain/spin
Mine too
Knob position should not matter, I just like to start in the 12 o'clock position
Hi...my lights will not blink after rotating the knob... please what should I do???
You have to rotate knob counter clockwise to reset. If the control is dead and not responding, and power supply is good, it's a failed control
My washer is a conversator washer and I unplug it and it's stuck in rinse
Stuck in rinse could be a lid lock, cold water, pressure switch/control, or a drain/spin issue
After I do the diagnostic. My machine doesn’t stop running water. The lid isn’t locking to engage the washer to start
Lid lock is a common problem
Nothing happens when I went in agitation mode. I could see it wasn’t moving the clothes. The tub moves and the middle agitator barely moved. I toke it apart and cleaned under it. It wasn’t bad. The tub also looks off balance Please help
Might be a hub, or actuator
How do I get it out of rinse mode..when I follow your directions I don't get the flashing lights or water running its just stuck..when I plug it back up it's still in rinse
Make sure the tub is drained, check cold water and pressure sensor. The pressure sensor is built into the board.
What was the cause of the noise during the spin cycle? Mine has it also when the drum is empty.
What should i do if my lid will not lock? Even during diagnostics, the lock never clicks and the agitator never moves. HELP!
More than likely, the lid lock would need to be replaced. Make sure the strike isn't damaged. (The white thing that inserts into the lid lock)
Thanks, not draining tried several times it wont do diagnostics test HELP
Any idea as of to why my amana washer has had the final spin flashing even after I unplug it try to reset it even doing the opening of the lid thing... it did let me get into diagnostics but never flashed any other lights than lid lock.. how do I clear it??? It s driving me crazy a little bit
Check lid lock, cold water valve, drain, and spin
If yoy run cold and hot it runs warm water in test mode
Mine isn't coming on at all nothing wrong with the outlet it worked then it stopped any help?
User interface or faulty connection between UI and main control
I can put mine in self diagnose mode no problem but when i try to recalibrate the machine i go press rinse and it lights up and stops nothing turns off
My situation is my red light is always on and sound click click click and dont do nothing
Probably a lid lock, check to see if the lock is activated
@@htgappliance yes always on the lid lock light and the sound click click click
@@Thebosspryt does the lid actually lock?
Hi my washer doesn’t stop clicking lid locked red light on always 😢
Please tell me how to unlock my lid. It's been locked for 3 days with my clothes inside
Sure wish someone would come up with a controller that you don't have to fight with when you want to wash some clothes.
The good Ole days are over my friend
My machine won’t go into diagnostics mode
Probably a control issue