For anyone thinking that a tap made out of a low grade bolt will be useless, don't worry, he wasn't making a tap, he was making youtube content. The tap doesn't have to work, it wont, but the youtube content did work, it made you watch two ads. Success!
Mire completo el video, me parece excepcional la destreza de el tornero. Mis felicitaciones. Dolo una observación: no sería mas económico comprar el machuelo? Saludos desde Salamanca Guanajuato México.
Hey, give these boys a break from all the ball busting! The Tap *will* be hard enough to cut threads in aluminum once or twice. Seriously, ...for a one off (field expedience) job I would too! Especially if it was a Grade 8 bolt!😉 Wakodahatchee Chris
Great work here and the last part was i think a way of hardening the metal however, is it for threading Copper as i doubt it could thread Steel . Thanks for sharing !
Bonito trabajo, pero lamentablemente no tendrá filo. Las herramientas que hacen en la fábrica lo hacen de varias aleaciones para darle la máxima dureza. Cómo cobalto, Niquel, Molibdeno y titanio Así como acero al alto carbono y al final le dan su tratamiento térmico. En cambio el tornillo con el que hicieron la herramienta solo contiene acero al carbono. Y no tiene la suficiente dureza para cortar metales.
For anyone thinking that a tap made out of a low grade bolt will be useless, don't worry, he wasn't making a tap, he was making youtube content. The tap doesn't have to work, it wont, but the youtube content did work, it made you watch two ads. Success!
Good for cutting threads in wood or plastic
by the way its a bolt not a nut
Mire completo el video, me parece excepcional la destreza de el tornero. Mis felicitaciones. Dolo una observación: no sería mas económico comprar el machuelo? Saludos desde Salamanca Guanajuato México.
I love watching these videos just to see unqualified people make things that are poor quality and don’t work on machines that were worn out years ago.
bless you LOL.never seen someone use chalk on threads b4 👍would been nice to see it put to use but nice job though 😎😎
Мне такой метчик за так не надо. Или я чего то не знаю, и у них болты из углеродистой стали? 😂
There are high grade bolts (8.8) and when it got hardened, it would probably work for hundred times or more.
Я тоже делал мечики из болта закалил в масле и всё работало сейчас магазинские мечики хрупкие и одноразовые а болт намного крепче
Hey, give these boys a break from all the ball busting! The Tap *will* be hard enough to cut threads in aluminum once or twice. Seriously, ...for a one off (field expedience) job I would too! Especially if it was a Grade 8 bolt!😉
Wakodahatchee Chris
Good working ❤
@11.00 Milling a slot on a manual lathe like that is frigging awesome. 😀.
Wait, show how well it cuts threads.
It won’t cut butter let alone metal. Lol
Good warking Pakistani qom
Good job best of luck
Great work here and the last part was i think a way of hardening the metal however, is it for threading Copper as i doubt it could thread Steel .
Thanks for sharing !
Where would you start the stocktake on the floor from?
you have to be dam good on a lathe. 👍
Excellent job ! 👍
quite impressive
Супер!!!🎉 Видно, що болт був з крицевої сталі (8.8; 13,9;) сам люблю щось зробити.
Пакистан посмотрел канал Мехамозга.
Super jest wykonany ten gwintownik ze starej śruby ale nie jest pokazane jak gwintuje Pozdrawiam serdecznie. 👍👍👍👍👍👍
Parabéns 👍🇧🇷🇧🇷
serviço perfeito meus parabéns muito bm....
He knows his stuff
salam vean y aprendan
انه لا يعرف سبائك الصلب.... هدا الحديد یتناسب لثقب الجبن.... لكنه فعل بشكل جيد.
JESUS CRISTO te ama muito ❤
У токарей кровь из глаз идёт при просмотре этого порно.
a bullnose would give better chip clearance
Damit kannst du vielleicht Affen vom Baum schießen aber mehr auch nicht
How in threading show you tap not in iron threading tap
из болта метчик не получится- сталь3 не закалится.
Так она и не закалилась, смотри 21-10 мин. Но больше 100 тыс. просмотров получилось.😀
Bonito trabajo, pero lamentablemente no tendrá filo. Las herramientas que hacen en la fábrica lo hacen de varias aleaciones para darle la máxima dureza. Cómo cobalto, Niquel, Molibdeno y titanio Así como acero al alto carbono y al final le dan su tratamiento térmico. En cambio el tornillo con el que hicieron la herramienta solo contiene acero al carbono. Y no tiene la suficiente dureza para cortar metales.
@@ErnestoZenteno-k1l hola Ernesto, buena observación, pero creo yo que lo que nos quieren decir en el video es la destreza de el operario. Saludos.
Туфта полная😂
It's a bolt , not a nut !
Actually it is a hex head cap screw. As if the terminology even matters.
Marche pas !! lol le taraud
Сувенир. Мы думаем, что покупаем всё плохое из китая, а это оказывается пакистанская подделка
The Chinese do a better job than that
That's a terrible thread it will cut a terrible thread
If you're going to talk shit at least use the correct term for the tool... it's a called tap, and it cuts threads.
@Qbear86 I know what the thread on a good tap looks like and I never mentioned what it was just about the thread so pull you head out of your arss
How do you sharpen on this machine? He's dead! The heartbeat is very big! This is garbage, not a machine! Scrap metal !
Any first year toolmakers apprentice can make taps and dies , it's very basic work.
Yeah but not from mild steel
@robames1293 graded bolts aren't mild steel.
@@snowflakemelter1172 That bolt was being machined on a lathe and the head had no markings so---graded?
@@snowflakemelter1172 Check out the shavings coming off.
테스트 안함?
Y ese tiraaaaadero???