Converting an Arduino PWM Output to a DAC Output

[@ami6packs]

Probably the best tutorial on how to get a DAC output from a pwm signal. Very nicely explained and i liked how you represent a square wave as sum of DC input + sine waves.

[@p_mouse8676]

Higher order filters will let you use higher sine-wave frequencies with the same pwm frequency. Passive it's possible to make a 2nd order filter with a Q=0.5 . With a single opamp it's possible to go up to a 3rd order (4th is technically possible but a little complicated) with a Q=0.707. (Max bandwidth)

[@wi_zeus6798]

Wow, I am really amazed by the in-deph approach! I appreciate it a lot. Nice video!

[@marcelmougenot]

Thank you very much! This is the best explanation that I found on the internet! Your lesson will be very useful for my master degrees!

[@odissey2]

I believe that Multiple Feedback topology LPF would work better than Sallen type. The Sallen filter has a direct path of the signal to the output, which shall bleed through. This is a known issue of the S-K topology, limiting its attenuation in the MHz+ region.

[@kaoshavoc]

Awesome vid. Wouldnt have of 255 bunary be 127 even. Since 0 is whwre it really starts it has an offset if one conpared to hiw we tging if numbers. So it should be 256/2 = 128 then minus the 1 offset because 0 is a value in code even though in life we see 0 as absense of value.

[@ForceTronics]

Yes you are correct, great catch!

[@kaoshavoc]

@@ForceTronics I have made that one off error sooooo many times. I am not sure I will ever stop making the error completly LOL.

[@bramSDASCL1759]

thank you,, great video

[@ForceTronics]

You are welcome!

[@workethicrecords5901]

I noticed you declared pin 10 in your code, but didn't seem to use it anywhere else, or in your example. Is it important for something internally?

[@SopanKotbagi]

no, it's not. it's just the part of the code which generates a 50% PWM wave on the true PWM pin as shown by him on the oscilloscope the first time. you can delete all code related to pin 10 and the sine wave would still be generated on pin 4

[@pradityaromansyah]

HELP
I want to use Buck Converter Module Arduino with input PWM signal. But, the input of the Buck Converter is a potensiometer. thank you

[@brianwong6195]

The Vpk-pk on the scope, is that reading your voltage ripple in your DAC output? 160mV. What would a good way to reduce the ripple?

[@bilalghanem4113]

How do you even get PWM fron pin 4 which is not able to give PWM (it doesn't have a ~ sign). Im trying to generate an ECG signal using arduino, any help?

[@ForceTronics]

What you see in the video is what I used. If I recall ecg signals are fairly precise and low amplitude. I would not recommend using a PWM signal. I would recommend using a dedicated DAC I that is 14 but or better. If you need it to be low amplitude you probably need some type of divider circuit

[@baltofarlander2618]

How do I change capacitor and resistor values in order to achieve higher cut-off frequency?

[@baltofarlander2618]

EDIT: Know I know lmao

[@michaelkeller7920]

What version of Microcap are you using?

[@yaqoobs.j.557]

In your code who frequency used? I want 31KHz what I worke to do this?

[@hukzero8227]

انا بعرف كتب و احصل ع PWM

[@liron28]

can i control the output voltage ? like change it from 1v to 2v ,5v etcetera
V=I*R
i want to change the V while R ramaine constante so I will change

[@ForceTronics]

Yes that is what a DAC is used for, vary a voltage level. Note that DACs are low current devices so they are meant to control high impedance devices.

[@stefanb.933]

Hello. how can the signal from the dac be downloaded on a 4 ohm coil?

[@ForceTronics]

No dac's are low power devices and would not have enough current to drive a waveform through a load with that little resistance. You would need an amplifier between the dac and the low impedance load. If you're trying to drive a stepper motor you should look at an h bridge circuit not a dac.

[@stefanb.933]

What amplifier do you recommend between the dac and the low impedance load?

[@ForceTronics]

I don't have amplifier model numbers or specs memorized so you will need to do the research

[@stefanb.933]

thank you. I would be happy if you make such a clip in the future. the idea is to be able to listen to the signal from the dac in the speaker, but it should be the same signal and not distorted. I tried with lm386, with a transistor and I didn't succeed ....

[@michelligata9439]

Hei, do you by any chance have any idea how to implement sine-wave generator in Arduino Uno using MATLAB simulink? i dont want to use the Analog pin, well Arduino Uno does not have DAC.

[@amienmarzuqhilman5677]

I have the same problem

[@amrelkomy3474]

hello
sir can you explain how the analogue output voltage swings between the positive and negative half cycles while the Arduino PWM is in positive half cycle only?

[@ForceTronics]

With this example circuit you should get a DC level with a low amplitude sinewave. The frequency of sinewave will match that of PWM signal. The phases of the signal should be about the same, but depends on specs of op amp you use

[@ghafoorsamadi2870]

Hi, very nice video, I like to know how can we use this signal for DC AC inverter cause we need two signals for - and + in DC AC inveter please.

[@ForceTronics]

Hello, I am glad you like the video. You are asking about inverter design and that is an area I don't have direct experience with so I am not the right person to give a DC to AC inverter tutorial.

[@DavidLeeMenefee]

Nice video. Thumbs up...PEACE

[@KrishneilGarib]

After converting it to a DAC how can you turn it into a proper sine wave with negative voltage peaks? (so where the 127.5 was added to the function we would want this to be at zero instead) but I am not sure how to actually use the output to get it negative. Any help?

[@ForceTronics]

Two approaches comes to mind. You could use the method presented in this video but you would need to find a microcontroller or other IC that can generate a differential (positive and negative) PWM signal. You would then need to pass it through an active filter with an op amp that has a negative and positive power supply. Note that the filter needs to be designed to allow the frequency of the sinewave to pass but attenuates the frequency elements of the PWM signal. Or you can buy an off the shelf DAC chip with a differential output. Note that such a DAC IC will also require a negative and positive power supply.

[@KrishneilGarib]

@@ForceTronics thanks so much for the detailed reply! If I was to find an off the shelf differential DAC IC, but the only had one main power supply, what would be the easiest method to convert/split this into seperate positive and negative rails to use?

[@ForceTronics]

Here is a link that might help: www.newelectronics.co.uk/electronics-technology/the-best-way-to-generate-a-negative-voltage-for-your-system/167618/

[@tientran007]

How to pwm sine 50HZ feedback volt AC ( 12vDC to 220vAC)?

[@ForceTronics]

You are asking about inverter design and that is an area I don't have direct experience with so I am not the right person to give a DC to AC inverter tutorial.

[@MitsuZer0G]

Why didn't you use a simple RC low pass filter?

[@ForceTronics]

You can use a simple passive RC filter but they suck for two reasons. First they have a gradual rolloff so your AC ripple on the resulting DC level will be larger in amplitude. Active filters have less loss or the op amp compensates for loss so the resulting DC signal better matches the PWM value.

[@SpacePortArcade]

Why bother configuring the PWM frequency if you're bit-banging?

[@htwt]

Easy way: LTC2644

[@oropeiro]

hi,can i vary the widths of the spwm(with same step) to change the amplitude of the output voltage,with the analoge read input as a feedback?

[@ForceTronics]

Yeah sure. Just make the measurement after the filtering

[@oropeiro]

@@ForceTronics thank you for answer man,i got it..