what happens if i change the factory 12 amps to 18apms, i feel it gives more torque to the motor. after 10 mins everything seems normal nothing warms up
@@mostafamansour1099 you notice a difference in torque and speed , depending on your controller and cable from the fases(blue,yellow, and withe) check the cable thickness they might support 20-25amps, ir it's more than 30 amps they might burn the cable (in my case with the cables my ebike brought)
For "Cruise control" when riding along get to your desired speed to cruise (must be above i think 10mph or so) and then... Hold the "Down" button for approx 5 seconds - You can now cruise at your chosen speed, it's great 👍😀 Cruise control will stop when you either move the throttle/throttle lever, or if you press either of your brakes. Walk Mode - Press and hold the "Down" button for approx 3-5 seconds. You can now walk alongside your bike and it will power itself as you walk with it (it helps if you keep hold of the bike 😅). Headlight ON/OFF - Hold "Up" button for approx 5 seconds, this turns your light on, hold it again for 5 secs it turns it OFF. To cycle through "max speed/battery current voltage/average speed/timer" press both together "UP" & "M" (middle button), pressing UP&M again will cycle onto the next of these 3 things - to go back to normal display press and hold "UP" & "DOWN" together. NOTE - My SW900 is a 2024 model, but these will probably work on any years model.
I need to really thank you I was messing around with the display not knowing what I was doing and my bike stopped working it wouldn't even go 5 miles an hour I had all these settings wrong I took this video and reset everything and now she purrs one think it was set at only 3 pas levels now I have it set to five than you very much
I want my 1st speed to be about half of the speed it is now. which is about 10mph. what setting would decrease that? this page has been very helpful. thank you
Setting number 15 is actually cutoff voltage. This is from the original SW900 manual. The manual presented in this video appears to be an outdated or wrongly copied one.
does anyone know how to do a factory reset on my gogo best gf 600 e mountain bike or what each setting should be on some one at work thougt it funny to change it please
thank u sooo much sir i did'nt know how to fix it . thank u for saying it slow so we can understand step by step with u. now i can in joy my birthday gife from my daughter. great job sir have an bless day
On my Wheelspeed 48v with S830 display I am on able to access P01(brightness) and P02 (km or miles). Is there a way to access the rest of the functions?
I have a 500w 36v kit but i have the same sw900 controller which is set to 12 amps also but 12x36 =432 watts. Should i just increase it to 14amps to get 504 watts? My battery is a 17ah battery if that makes any difference.
Gears 1 to 4 I am able to pedal, but 5th is just way too fast. I mean 4th while I pedal is about 15mph, but than I put t in 5th and it's 23mph and i can't pedal that fast. How do I fix that?
Hey, my bike it turned off because of battery, and when i tried to use once the battery was load, i met with a 4 digit code. I tried a lot of combinations but im not success. Is a magnum metro 48 v
Thanks, I was looking for this. I was very disappointed when I took my first big ride and when I dismounted to explore my display would blank out and I couldn't get it back without restarting it which zero's out the trip odometer. I now have my screen timeout set to zero. What are the other two setting? Mine was on 3 from the factory. Your link to the instructions has been hacked. It doesn't work. Thanks for all the help!
My SW900 gives a breakproblem. The brakes are fine, but the motor doesn’t work because of the fact the the display doesn’t reset itself. Is there a way to reset the display? Thanks for the answer. I really like the explenation films. Greetings from the Netherlands 👍
It should reset if you remove the battery. The brake problem could be the hub motor. It has a built-in brake in some motors. Good luck. Thanks for watching and have an Awesome day.
Just because the brakes work doesn’t mean there’s a problem with the motor it could be that you need to calibrate the rear brake to the motor so that it will cutoff the motor when you brake
Can someone help me please. My Shengmilo has pure electric mode from pas1-5. Zero is non assisted. But the bike Lankeleisi 750 plus. Pure electric is only on 0. All else is assisted. Can it be changed ?
Qn: Can I use the LCD to change my Top Speed, and then go back to LED? Or will the LED always drop back to its own hard wired settings? (Rad Mission 1)
Turn the current setting up. Also shunt mod. Can get nearly 3000w out of a stock 1000w controller. Just be careful on hills. And don't stay at max throttle constantly. Once you get to max speed you can pin the throttle and no harm will happen. Because amp draw decreases significantly. It's when accelerating or climbing hills that you need to be careful how much current you draw. Can cook the motor or your controller adding solder to the shunts increases current. The more solder you add the more current you get. My display allowed me to set my current to 30 or 32a. I can't remember the exact number. Top speed of 35mph and 1400w constantly from a 1000w controller. Shunt modding allowed me to pull 2900w. I had to use an external watt meter. Once you add solder to the shunts the stock display no longer reads the watts/current accurately.
After the mod my top speed was closer to 45mph. 26 inch wheel. I'm actually repurposing an ebike motor to make a home made euc. Using a vesc controller. Im switching my ebike to a vesc controller as well. The flipsky 75100 aluminum pcb controller. Can do 20s at 100Amps. It also does field weakening and foc. Not a bad 120.00 investment.
If you can't find the settings on the video just print out the instructions and follow the instructions. Very easy to change back to 20 mph. Good luck.👍
Harold...tried your system...my Rad City has only 4 options marked SEE 1,2,3,4. It only allows me to change tire size, top speed, illumination, and mph/km. Any experience with getting deeper into the programming of RAD specific controller/display. So frustrated by it turning odometer off when a brief stop happens... thx
Thanks for the question. I don't have any more information at this time. Check out some other TH-cam channels for more information. Thanks for watching.
Si es de 48v y le pones 52v 0 60v o 72v aparecerá que no esta cargada aún que la batería esté completamente cargada lo que tienes que hacer es poner 48 en la configuración Si es de 36v pon 36
There is a USB port underneath the face of the display on the right side as you are facing it. It's not live at least on my SW900. Is there a way to activate that and/or is it disconnected on the inside of the unit?
Hey man, I upped the speed limit on my display, but I cannot figure out how to cut it on the controller. I have a hurley mini swell. The controller is built into the battery housing, and they dipped the computer chip, and wiring in a grey gel. I can't figure out what to cut
Hello, P6 is for tyre size. If I have 28 inch wheel do I have to add 1 inch for top and 1 inch bottom for tyre thickness? So the P6 setting should be 30
@@ianmangham4570 thanks for your reply but do have any extra information to support that. Because I had an electric scooter and the 11.2 setting included the tyre
I originally had pedal assist when I first hooked everything up. My instructions are almost spot on with your walk through. However, somehow I have changed the pedal assist setting and I am not sire how I did that. I’m
@@demusmarcus8240 You just won't get instant power from pedalling, Even with a 12 magnet system and the assist delay setting set to it's lowest.. There will always be a delay of some number.
@@demusmarcus8240 That's the ticket. That's what I do and I guess many people do, Bonus of having a throttle :) I was spoilt with my last ebike, It had a yamaha mid drive which had zero cadence torque sensing - Power as soon as you touched on the peddles.. I do miss that, But I love my 1000w hub bike it's more fun to cruise on.
Whilst travelling whatever speed you want to set cruise to you simply hold (on sw900) the 'down' button for approx 5 seconds and then it will self cruise at this speed (until you touch/move either the throttle or you apply the brakes, then it goes back to normal)... Short answer - Hold 'down' for 5 seconds. My sw900 was purchased bought in 2024 on a Voilamart kit.
@@Will-mx7gl 30 is fast. That's probably as fast as it will go unless you increase the battery size. I have not tried that myself. Good luck and have fun.
Hi Harold I just installed that monitor SW 900 on a 3000W motor 36V- 72V. I need to de restrict it ot only goes to 19.9km I dont use pedal assist. Can I set up battery to 60V My battery reads 57V. I will review the video and most likely print out the manual. Any help is well appreciated.
I can say that works only on specific controller and display. Some controller has password set up and even if you have password they programmed to have specific limit that will not make bike faster . Those setting are set for liability as some countries has restriction on max speed. I would not recommend to mess around as it can damage battery or motor and controller. Stay safe !
@@nightwolf5831 no it doesn't have any voltage settings just the gauge that shows u the battery bars ,the speed and the mileage ,I use a next battery and same thing
Hi Harold, thanks your video, it’s been 1 year and wanted to know your experience updated upon your SW900 LCD Display. I have ordered 2 ebike 12000w with the SW900 LCD Display. I herd there’s a new model ukc1 led color display that just came out not to long ago. But yeah I seen good and bad reviews of sw900, what’s your experience feedback on it ? Is it all weather proof? Is it reliable over all ? What’s your recommendations ?
This is the best video I found yet
This is for sure the best explaind sw900 user manual iv seen and so this has help me out and you have earn your self a new sub!
Best explanation I've seen. Just bought my bike with the same display. Thank u
this kit does it comes with a sine wave or square wave controller
what happens if i change the factory 12 amps to 18apms, i feel it gives more torque to the motor. after 10 mins everything seems normal nothing warms up
Did anyone advise you regarding cuz I wanna know myself 😅
@@mostafamansour1099 you notice a difference in torque and speed , depending on your controller and cable from the fases(blue,yellow, and withe) check the cable thickness they might support 20-25amps, ir it's more than 30 amps they might burn the cable (in my case with the cables my ebike brought)
Excellent descriptive video...thanks mate
@@macca5986 I think you meant to comment this on the video, but instead you replied to a comment.
Is it still working?
This video is good it fixed my display problem he's 100% right about all settings
For "Cruise control" when riding along get to your desired speed to cruise (must be above i think 10mph or so) and then...
Hold the "Down" button for approx 5 seconds - You can now cruise at your chosen speed, it's great 👍😀
Cruise control will stop when you either move the throttle/throttle lever, or if you press either of your brakes.
Walk Mode - Press and hold the "Down" button for approx 3-5 seconds.
You can now walk alongside your bike and it will power itself as you walk with it (it helps if you keep hold of the bike 😅).
Headlight ON/OFF - Hold "Up" button for approx 5 seconds, this turns your light on, hold it again for 5 secs it turns it OFF.
To cycle through "max speed/battery current voltage/average speed/timer" press both together "UP" & "M" (middle button), pressing UP&M again will cycle onto the next of these 3 things - to go back to normal display press and hold "UP" & "DOWN" together.
NOTE - My SW900 is a 2024 model, but these will probably work on any years model.
You could also maintain any throttle setting for 5 seconds and it will hold it there until you speed up or apply brakes.
What’s the other modification if u wanna keep it at 50mph?
I need to really thank you I was messing around with the display not knowing what I was doing and my bike stopped working it wouldn't even go 5 miles an hour I had all these settings wrong I took this video and reset everything and now she purrs one think it was set at only 3 pas levels now I have it set to five than you very much
You are welcome. Thanks for watching and have an Awesome day 😊
I got from 18.6 mph to 20.4 mph Thanks im still tryna get it faster tho
I want my 1st speed to be about half of the speed it is now. which is about 10mph. what setting would decrease that? this page has been very helpful. thank you
Setting number 15 is actually cutoff voltage. This is from the original SW900 manual. The manual presented in this video appears to be an outdated or wrongly copied one.
does anyone know how to do a factory reset on my gogo best gf 600 e mountain bike or what each setting should be on some one at work thougt it funny to change it please
thank u sooo much sir i did'nt know how to fix it . thank u for saying it slow so we can understand step by step with u. now i can in joy my birthday gife from my daughter. great job sir have an bless day
Hey only like the first one or two settings work and then when I try to go up or down it won't click anywhere and do anything
Amazing vid of got a Cruze73 retro e-bike and now I’ve managed to go into my settings and sort this out! Such a good vid!
So do you have to figure out what display your bike uses first or are they all the same?
Thank you for the video, Where did you get the printout?
On my Wheelspeed 48v with S830 display I am on able to access P01(brightness) and P02 (km or miles). Is there a way to access the rest of the functions?
I have a 500w 36v kit but i have the same sw900 controller which is set to 12 amps also but 12x36 =432 watts. Should i just increase it to 14amps to get 504 watts? My battery is a 17ah battery if that makes any difference.
On 14 i upper the amps by 2 amps and it made the bike pull harder
Harold, have you ever figured out PO5 ? There are actually 6 optional grade settings. - Chuck
How do I get it to go faster then 28 mph? Thanks for the great video.
Buy a more powerful controller/motor/battery
Can i get the link please for directions
I recently got a ebike and would like to go faster than 24 km, do you know about zunuo 48v contoller? I could find the speed wire. Thanks
Make the wheel size from 27.5 to 17 . And set the pas from 3 to 5 modes . After that you can ride 34 kmh :)
Thank you for such a thorough video. Helped me so much.
Gears 1 to 4 I am able to pedal, but 5th is just way too fast. I mean 4th while I pedal is about 15mph, but than I put t in 5th and it's 23mph and i can't pedal that fast. How do I fix that?
You don't need to pedal that fast, that's the whole point of assist.
The bike will still go the 23mph if you pedal slower
Hey, my bike it turned off because of battery, and when i tried to use once the battery was load, i met with a 4 digit code. I tried a lot of combinations but im not success. Is a magnum metro 48 v
You are the 2nd person that has had this issue. I have never had this happen. I would call the company that sold you the bike and ask them. Good luck.
my setting skip from p8 to p13, what do i do?
I haven't run into that. I would order a new one.
Thanks, I was looking for this. I was very disappointed when I took my first big ride and when I dismounted to explore my display would blank out and I couldn't get it back without restarting it which zero's out the trip odometer. I now have my screen timeout set to zero. What are the other two setting? Mine was on 3 from the factory. Your link to the instructions has been hacked. It doesn't work. Thanks for all the help!
Does this work for my 22mph max cargo Eunorau ebike?
My SW900 gives a breakproblem. The brakes are fine, but the motor doesn’t work because of the fact the the display doesn’t reset itself. Is there a way to reset the display? Thanks for the answer. I really like the explenation films. Greetings from the Netherlands 👍
It should reset if you remove the battery. The brake problem could be the hub motor. It has a built-in brake in some motors. Good luck. Thanks for watching and have an Awesome day.
Just because the brakes work doesn’t mean there’s a problem with the motor it could be that you need to calibrate the rear brake to the motor so that it will cutoff the motor when you brake
What’s the difference between trip and odo? 🙏🏽
total miles vs individual trip
Where is the next video for the speed limit control
I have a different display for my daymak max large do most of the displays use the same number
Sorry maybe it's c11 I forget
Hpw i adjust the baytery power
Can someone help me please. My Shengmilo has pure electric mode from pas1-5. Zero is non assisted. But the bike Lankeleisi 750 plus. Pure electric is only on 0. All else is assisted. Can it be changed ?
It's probably your controller. Check the magnets at the peddle crank. Thanks for watching and have an Awesome day.
Qn: Can I use the LCD to change my Top Speed, and then go back to LED? Or will the LED always drop back to its own hard wired settings? (Rad Mission 1)
Changing the tire size will make it go faster. Good luck and have fun.
@@HaroldJackson should I use a smaller tire or larger tire to go faster
So what's the other modification, besides the speed limit, that we have to modify in order to get more speed?
th-cam.com/video/fTFiXlz7RJQ/w-d-xo.html remove this wire
Get a big voltage battey for more speed. This setup can handle 60v easily
@@vincenzotatti3325 can I just add a 60v battery to my 48v bike
Turn the current setting up. Also shunt mod. Can get nearly 3000w out of a stock 1000w controller. Just be careful on hills. And don't stay at max throttle constantly. Once you get to max speed you can pin the throttle and no harm will happen. Because amp draw decreases significantly. It's when accelerating or climbing hills that you need to be careful how much current you draw. Can cook the motor or your controller adding solder to the shunts increases current. The more solder you add the more current you get. My display allowed me to set my current to 30 or 32a. I can't remember the exact number. Top speed of 35mph and 1400w constantly from a 1000w controller. Shunt modding allowed me to pull 2900w. I had to use an external watt meter. Once you add solder to the shunts the stock display no longer reads the watts/current accurately.
After the mod my top speed was closer to 45mph. 26 inch wheel. I'm actually repurposing an ebike motor to make a home made euc. Using a vesc controller. Im switching my ebike to a vesc controller as well. The flipsky 75100 aluminum pcb controller. Can do 20s at 100Amps. It also does field weakening and foc. Not a bad 120.00 investment.
up and down did nothing on a suntour hsec system
The link do the instructions don't work it says not found
I will find another one as soon as I have time
HOW DO I RESET MY Led DISPLAY, instead of my e-bike going 20mph it only goes up to 12mph.
If you can't find the settings on the video just print out the instructions and follow the instructions. Very easy to change back to 20 mph. Good luck.👍
It could also be that the tire size is set wrongly.
I have error
Code 08 any idea?
Where is the manual for downloading
Have the same bike and the speedometer won’t read any higher than 2mph. Any ideas?
I’ve just gone on them setting and it’s drained my whole battery in seconds what has happened do you think?
Sounds like a short.
Harold...tried your system...my Rad City has only 4 options marked SEE 1,2,3,4. It only allows me to change tire size, top speed, illumination, and mph/km. Any experience with getting deeper into the programming of RAD specific controller/display. So frustrated by it turning odometer off when a brief stop happens... thx
Thanks for the question. I don't have any more information at this time. Check out some other TH-cam channels for more information. Thanks for watching.
My new ebike is showing e07 & not working. What do I need to do?
S866
Hi my battery is full but my screen is saying it's not charged. Can you help
Sounds like you have a bad connection between the battery and the controller. Check all connection.
Si es de 48v y le pones 52v 0 60v o 72v aparecerá que no esta cargada aún que la batería esté completamente
cargada lo que tienes que hacer es poner 48 en la configuración
Si es de 36v pon 36
So if I want to go over 50 mph what is the modification I need to make? my motor is rated at 2000 watts !
Not all bikes are the same. On this one we disconnected the blue wire. It just unplugs. Good luck!🚴
Probably need more battery or a bigger controller. My motor is 750 and 1000 peak as I got the bike but its good to 2300 watts
At my display it's parameter 8, speed limit. possible values 0 to 100. 100 is no limit (reaching up to 80km/h with 2000W Motor)
Can someone tell me y mine only goes to p4
Hi, do you if theres a way to deactivate the cruise control?
I don't know
How do you reset the bike??
Can i put it on 60v on a 52 v battery
Good question. I would email the manufacturer and ask them. Thanks for watching and have an Awesome day.
Does not work for me if I keep it pressed the display turns off at 0:50
i saw that you also can use this display with a 72v battery
Kool and thanks for the information. Have an Awesome day
So for number 14 ,my bike is a 36 volt 7 amp should my setting for that be 7
Reseat to factory specs using the C function Y or N think it's c17
Hi for some reason my battery life bars never go out, Always shows full charge. Any advice?
Sounds like a short in the lights on the battery. Good luck.
Did you fix your issue? I bought a used bike and the battery indicator does not show any bars but my battery is fully charged. Any help appreciated
This info has incorrect info for BeeCool bikes that uses a slightly different version of the SW900
Thanks for the information. Most people don't understand that. Thanks for watching and have an Awesome day 🙂
16 resets odometer? Like I have 90 miles on it, if I reset it, it’ll go back to 0?
That should work. Thanks for watching and have an Awesome day 🙂
@@HaroldJackson mines the s900 I just realized, do you know how to do it on that one? Only goes to 12
I have sw900 control 1500 watt motor 52v 20ah battery can I upgrade to 72v battery thanks anyone
There is a USB port underneath the face of the display on the right side as you are facing it. It's not live at least on my SW900. Is there a way to activate that and/or is it disconnected on the inside of the unit?
It sounds like a defective unit. See if they will replace it. Thanks for watching and have an Awesome day 😊
The usb port powers up when your bike comes on.😊
Hey man, I upped the speed limit on my display, but I cannot figure out how to cut it on the controller. I have a hurley mini swell. The controller is built into the battery housing, and they dipped the computer chip, and wiring in a grey gel. I can't figure out what to cut
Get another controller
Hello, P6 is for tyre size.
If I have 28 inch wheel do I have to add 1 inch for top and 1 inch bottom for tyre thickness?
So the P6 setting should be 30
No, this is factored
@@ianmangham4570 thanks for your reply but do have any extra information to support that. Because I had an electric scooter and the 11.2 setting included the tyre
@@strawman9410 I have ALL SETTINGS, 10 years building ebike
@@strawman9410 Get a friend in a car to check speedo
My bike was stucc on kmh thanks alot
useful info .. for setting up the controller ... in uk the word HACK would go further , suggest new software of hardware
How do i change the kilometres to miles on the display ?
I put a link in the description that will tell you how to do that. Thanks for watching and have an Awesome day.
@@HaroldJackson you are awesome 👏🏼 thank you so much. 😉
Ciao si puo fare sulle fat bike?
Hey thats for 900sw lcd 😂
My Question is does it apply to all E-bikes? Mine is G51 Lcd!
If I tell my display I have 29 inch tires, but I actually have 26, will it make me go faster?
No. Your speed indicator will be off. That setting is to calibrate the speedometer.
If u tell it your wheels are smaller than they actually are your bike will go faster.
Does this work with any controller?
I'm
P11 should be set to 1 not 24 if you want the pedal assist to kick in sooner.
Mine is set to 1 but still takes a couple peddles for the motor to kick in do you have the same problem?
1
@@demusmarcus8240 did you fix this ?
Why i have error word in the bottom of screen ?
Probably got moisture or water in the display. I found out the hard way they are not waterproof.
@@HaroldJackson Are they not water resistant at least? Can't they keep rain out? Seems pointless if not..
Hi my bike says watt error any ideas ?
Remove battery and charger it.
Very helpful 2 👍🏾👍🏾 up
Thank you so much for the step by step information it was most helpful!
Thanks for watching and have an Awesome day.
I originally had pedal assist when I first hooked everything up. My instructions are almost spot on with your walk through. However, somehow I have changed the pedal assist setting and I am not sire how I did that.
I’m
Change P11 to 1 not 24
My pedal assist always kicks in after a peddle or so I can’t find a way to get instant powers from the pedal assist like it is with the throttle
@@demusmarcus8240 You just won't get instant power from pedalling, Even with a 12 magnet system and the assist delay setting set to it's lowest.. There will always be a delay of some number.
@@mozzjones6943 thank you only way to bypass the delay is to rev and peddle at the same time
@@demusmarcus8240 That's the ticket. That's what I do and I guess many people do, Bonus of having a throttle :) I was spoilt with my last ebike, It had a yamaha mid drive which had zero cadence torque sensing - Power as soon as you touched on the peddles.. I do miss that, But I love my 1000w hub bike it's more fun to cruise on.
Doesn't work on my Santa Monica...still only does 20mph!
Thank you!
Help me a lot! Thanks for Brasil 🇧🇷
Just take the wire off that's for the magnet the sensor some of them just unplug check out your controller
Yo D head where the video that you say NEXT to put the bike faster
cruise function?
That would be an add-on on the throttle. Thanks for watching and have an Awesome day 😊
Whilst travelling whatever speed you want to set cruise to you simply hold (on sw900) the 'down' button for approx 5 seconds and then it will self cruise at this speed (until you touch/move either the throttle or you apply the brakes, then it goes back to normal)...
Short answer - Hold 'down' for 5 seconds.
My sw900 was purchased bought in 2024 on a Voilamart kit.
What happens if you put it on 36 volt and you're running a 48 volt battery??
something will burn :)
Thanks
can you post the instructions to another site your site is broken
THANK YOU
Nice
What happens with Error 2 and/or the screen cuts off??
Sounds like a bad screen
Screen works error code 2.
I always thought that you guys use kmph not mph
UK we use MPH
Thanks for the info 😊.,.
Now I drive my bike with 😂
Thanks for watching and have an Awesome day 😊
Hi again .. do you know how to increase the speed ? . The maximum I have is 30 mph ,.
Thanks for your reply
@@Will-mx7gl 30 is fast. That's probably as fast as it will go unless you increase the battery size. I have not tried that myself. Good luck and have fun.
Thank you so much!
You are welcome.
Very interesting 🙃
thank u so much!!!!!!
You are welcome 👍
you saved my Day:) thankyou
Hi Harold I just installed that monitor SW 900 on a 3000W motor 36V- 72V. I need to de restrict it ot only goes to 19.9km
I dont use pedal assist.
Can I set up battery to 60V
My battery reads 57V.
I will review the video and most likely print out the manual.
Any help is well appreciated.
I can say that works only on specific controller and display. Some controller has password set up and even if you have password they programmed to have specific limit that will not make bike faster . Those setting are set for liability as some countries has restriction on max speed. I would not recommend to mess around as it can damage battery or motor and controller. Stay safe !
Hi on my gauge the battery icon is blinking and not showing the bars ,what would the problem
@@nightwolf5831 no it doesn't have any voltage settings just the gauge that shows u the battery bars ,the speed and the mileage ,I use a next battery and same thing
Can it be the controller, the controller is in the battery case ,the battery fit in a case on to the frame
Hi Harold, thanks your video, it’s been 1 year and wanted to know your experience updated upon your SW900 LCD Display. I have ordered 2 ebike 12000w with the SW900 LCD Display. I herd there’s a new model ukc1 led color display that just came out not to long ago. But yeah I seen good and bad reviews of sw900, what’s your experience feedback on it ? Is it all weather proof? Is it reliable over all ? What’s your recommendations ?
No it's not weather proof. We have had issues with water getting into the sw900.
@@HaroldJackson Harold thank you for your reply, I’ll contact manufacture about this issue
I really hope you read your messages quickly and will respond back it's already been a week since I haven't had my bike running