God damn Bardwell, you are on it. Every single time I have a question, Papa Bardwell has the answer and has already made a video for it. You're awesome!
I’ve been into RC for 20yrs now and even professionally raced 1/8 buggy for a little bit so I have a fair bit of experience. With that said I have recently started looking into the FPV drones 3/5” and most of the stuff I’ve watched is either a little to “beginner” oriented or they just gloss right over a lot of key points and information. Your videos have been crucial for me to feel confident in building a drone that will fit my budget and not be a waste of money because I outgrow it or went too far. Thank you for the help. Also just the right amount of humor so the videos aren’t boring in the least I really enjoy them.
About soldering: I went into the hobby trying to avoid it. I got a TH2 Freestyle BNF. I was learning to solder a week later because I ripped the battery connector leads off. You just can't avoid it.
17:55 I'd recommend using display_name for your pilot name and leaving craft name for the - well name of the craft. When you save your config it will be named by craft name, that way you can keep track of your library of config dumps much easier without having to manually rename them. display_name (pilot name) you can copy into your osd setup commands for every quad.
I think this is surprising for the cost, at the time mine was $69.99. Most the quads I like well more in this category are either double the cost or at least $40 more. Sorry if I am out of line.
@@jermadjesty I haven't given it away just yet. I did take it out for about a week post review. Maybe another 15 flights or so. Still flies just like it did. :)
I just bought the Flight Controller from this quad on it's own from DarwinFPV for a self build. £33 (43.19 USD) shipped from china for a 15A AIO F411 FC seems like a pretty good deal these days and sure some of the solder pads are in odd places, but so far it's just worked...
Great spending Sunday morning with you JB, nice to be back into quads again. I'm sure that cute baby is running around grabbing stuff they shouldn't by now ;) Take care.
I've had this one for a while, I like it. It's a fun little drone, upgraded the camera though, in lower light the picture gets really washed out otherwise it's a lot of fun to fly and I'm not too worried if it gets wrecked.
Hey Joshua, There's an excellent double sided tape made by Gorilla Glue that is already double the thickness of the Scottch brand and holds 35=38 pounds per square inch. really sticky and squishy. I used it to hold my Crossfire Diversity and have had many hard crashes and has never come off. $3.00 a roll at Wal-Mart.
If you're using dshot beacon instead of a beeper you might want to increase the Beacon Tone value so it's a bit louder. It looks like it comes set to 1 by default. I usually set mine to be 3 or 4 and then test it to make sure the motors don't heat up too much. Also if you're going to arm your quad and spin the props as a means to find a lost quad, then I recommend doing it with turtle mode on. That way you can just leave the quad armed and wiggle the stick periodically to listen for it. If you're unable to takeoff then there is a good chance you have obstructed props, so it should be a lot easier on your ESCs. If neither of those are loud enough to help you find it, then I like to put a single patch antenna on my goggles and use that to figure out what direction the signal is strongest. That usually gets me close enough to hear the props spinning. I've been enjoying the beginner themed content lately. Can't wait for the review to come out for this.
I was a little skeptical about this quad when I saw it a little while back especially when I saw the motors they look antique to me and I'm a newb!!!! Lol however I do love the price and overall it's not a bad quad....now I'm really stoked on getting it having these step by step instructions on getting it set up just sold it for me JB THANKS👍 can't wait to see you rip it✌
They look ancient because they are the motors off the original babyhawk from emax that was probably released like 4-5 years ago. They work fine though.
It's funny that your three pads for sbus is presoldered, because mine came with a pre installed wire.. although the connector is not needed, so I'll be snipping it off
I got one of those, unfortunately that AIO in it is not that great. The boards have really weak voltage converters on them. First board I had smoked out right away on 2s, and the second one I had that came in the Ape died after about the 10th flight, again it was the converter.
This one's gonna be my first outdoor unit. I'm going to replace the VTX with a Happymodel 300mW VTX/ELRS receiver combo, and I'll be upgrading the VTX antenna with a HGLRC lolipop. I have a set of LDARC 1104 7500kV motors on hand that I'm thinking on installing. Stoked to get outside and not have to worry about range issues.
Hii did you install the 1104 motors 7500 kv??. I think to install the same motors. If installed how it works. Can fly with 1s? How are compare with stock motors??
@@stelic9515 Unfortunately, the mounting holes don't match. And no, it won't fly with a 1S, even with 7500kV motors. I think you'd need at least 12000kV or better.
That's the problem with ALL of the parts used in these ultra cheap ass quads! They use very old parts no one uses or wants anymore! They have issues and burn out quick. Buyer Beware! 🥴
i been flying one of these on 3s for 2 months and crashed the hell out of it in trees, concrete, buried it in sand. its a fuckin trooper! the only thing that happened to it is the camera came loose from its 3d print. a motor eventually came loose after lots of crashes and flights and no maintenance and it cause the props to cut the wires. upgraded to 1204 5000kv and thing flies soo good.
Yeah, but don't you see... Once you put a dime into upgrading or repairing this hunk of junk, you might have well bought a quality, name brand quad, and had better performance from parts actually used in this decade, and you'll have long life and possibly no failures from a name brand! And, you maybe have to add 20 bucks to the cost of this Total POS! 🤔👍 Go ahead, buy it, and find out what I've already learned! Just trying to help you not throw your money away. Because that's what you do by buying this ultra low end garbage! 🙈🤮
@@KOrnhOliO1 as much as ive flown and crashed this thing without much problem im more than satisfied with its performance and durability. i was expecting much less
im kinda not confident about those hole not made well to receive screw from propeler... its like my 2.5 inch 2s 8700kv eat 27 amp total... if the prop dont have screw it fly off... ... surely there is on thingiverse some print to make to put on the top of the motor put screw and with new hole for prop screw to fit (kinda need short screw .. but 2 time 3 turn of screw in pla should lock it in place ... )
That double sides stuff sticks better if you just press it firmly for 10-15 seconds. If you wiggle it won't stick as well. At least in my experience and what the instructions say on the stuff I use but you are using a different kind than I use 😆.
I had the Ape for a week and its great, XLRS is my choice to so now this is my favorite 3 inch , 80 buck delivered to europa is a bargain. got the 129 gps long range to and the quality is way better than eachine's, so far the Darwin company has not disappointed
Well great tutorial! Just dont let this be your first drone if you have bad eyes lol...i will be buying theG1600 microscope,i seen 1 of your vids with same ish version dont think this 1 was released yet.anyway,cheers for the video!
Hi Joshua. I'm a fan of your channel and I love how much knowledge I learn from you. Thank you. So I'm just about to purchase a Baby Ape Pro V2 ELRS from RaceDayQuads and I really want you to get the credit. I see you have a link to it above but I want to get the Pro model instead. Can you please give me an affiliate link to that drone? I'm not sure how that works. I'll probably also buy some batteries and a charger. I hope you'll get credit for that too.
Buen vídeo estoy por comprar el pro, pero no sé qué batería sería mejor?! La 3s de 11v verdad, el conector es el xt30 o xt60?? Puedo poner una de 1500mah?!? Gracias
I got one of these and have gone through 3 receivers. 2 brand new and one removed from a working drone. Two were betafpv mini elrs and one flywoo one. All with the tower antenna. The first one stopped working while trying to flash it. The second one did similar. The third one I took from another working quad. It worked for a minute. Long enough to bind and arm the quad. The next morning I tried it and it just lights up solid but has no connection to the controller. I have it hooked to the 4.8 v vcc, and the rx and tx both have around 3 v. I’m at a loss here and don’t know what I’m doing wrong
I have started to use only 3 wires on my ELRS rxs, as I don't need telemetry send back to my transmitter.Flying FVP, all needed info is to be seen in the OSD anyway.
Hey dude nice video ,buddy I'm got a problem I think , my video signal I've lost over 10mts , so I think that the power off my vtx is low ,how can I change it ? I bought the darwin baby ape V2 ,tks for all
I think they tinned those pads since SBUS is so common. Mine were pre-tinned, same pads. Or maybe they just test it real quick with an SBUS RX. Not a returned unit I'm sure.
Hi sir.. Im from malaysia.. Can you make a complete video for install gps module and smart audio also how to activate softserial for babyape pro? Sorry im new on fpv drone.. Also how to setup in beta flight.. Please sir help me
Hi Bardwell, thank you for all your vids, you're helping me a lot!! theres is just one thing with the darwin drones, i always have problems with the vtx! when i install my own all is working fine, but the normal vtx from darwin is so strange! i have problems with the powervalues and levels and low power disarm mode! it's just not working when i start the drone sometimes the power ist set to 200 and somethimes to 600 but never 600 as i've set! and low power disarm is not even working (sometimes it works) and when i got the drone, the osd was so laggy, so i needed to cut some tasks in the CLI, do you know if a firmwareupdate might fix the issue? i have betaflight 4.3.1 and i don't know if its safe to update the vtx! this is my second drone from darwin and i had the same issue till i replaced the vtx myself
Hi all please help me i buy rafiomaster pocket i have receiver elrs nano 2.4 and i have problem my rafiomaster pocket My remote doesn't respond on the receiver tab, even though I've set everything up correctly
Hi. Just received my BabyApe Pro. Aside from the rubber band, I didn't receive any other battery strap. What other strap did you receive? I saw two short velcro straps in the box, but they are too short to hold a battery. Cheers.!
Please unprivate your video "inverted pitch is dumb and you are dumb if you use it", it was hilarious and really helped convince me to abandon trying to control quadcopters like an fps. Maybe at least give me access? I promise I wouldn't reupload or anything. :^) Just would like to show it to my bro.
Hey dude nice video , so man I hust got a quad like that and I need I hand if possible I'm noob , I'm losing the video signal over 10 meters way I'm trying to change de vtx power but I'm not getting successful,could u help me pls
Thank you so much for putting up this video, I finally got around to soldering my ape on friday. Quick question? is it normal to have only 6 or 8 ft of range before video cuts out to static? Ive havent been able to fly this ape, could EP2 be interfering with video signal? im using true patch and axil omni on skyzone 04x V2 googles.
Thanks Joshua I'm new and just got this quad I have to put a dsmx receiver on this don't really know we're or how to do it any help would be greatly appreciated
Hello, just found your channel and I'm considering buying the Baby Ape Pro! I just noticed they have kits on their website with controllers, goggles and all that. Would be really fun to see you do a full review with their ready-made kit to see if they're anything good to have or not :)!
![☀ Бомж ВХОД в FPV мир! А есть ли смысл? + РОЗЫГРЫШ [DarwinFPV Baby Ape | Radiomaster T8 Lite]](http://i.ytimg.com/vi/dOE257XM4Kg/mqdefault.jpg)
![[🔴LIVE] งานประกาศรางวัล MAYA TV AWARDS 2024 : มายามหาชน](http://i.ytimg.com/vi/nwmWYXXVwBY/mqdefault.jpg)
God damn Bardwell, you are on it. Every single time I have a question, Papa Bardwell has the answer and has already made a video for it. You're awesome!
I’ve been into RC for 20yrs now and even professionally raced 1/8 buggy for a little bit so I have a fair bit of experience. With that said I have recently started looking into the FPV drones 3/5” and most of the stuff I’ve watched is either a little to “beginner” oriented or they just gloss right over a lot of key points and information. Your videos have been crucial for me to feel confident in building a drone that will fit my budget and not be a waste of money because I outgrow it or went too far. Thank you for the help. Also just the right amount of humor so the videos aren’t boring in the least I really enjoy them.
About soldering: I went into the hobby trying to avoid it. I got a TH2 Freestyle BNF. I was learning to solder a week later because I ripped the battery connector leads off. You just can't avoid it.
welcome to nerddom
Wanna fly quads you got to learn to solder
Same copter, but i bought the soldering thing ahead of time and was ready, but god damn the thf 2 breaks like a twig
Charl south Africa really appreciate your channel 🎉🎉🎉
And I live in middle of nowhere,so I must do everything my self
9:40 I love that little enactment! 😂 Never change Joshua, you're a gem in this hobby and pretty much the sole reason me and many others are in it :)
I love the black and white video snippets! "I'm going to fly, I'm not going to drive a tripod..". AMEN!
17:55 I'd recommend using display_name for your pilot name and leaving craft name for the - well name of the craft. When you save your config it will be named by craft name, that way you can keep track of your library of config dumps much easier without having to manually rename them. display_name (pilot name) you can copy into your osd setup commands for every quad.
Can wait for mine just bought the Pro V2 version! 🥳🥳
I am so glad you kept the rant about flying a tripod 😂😂😂
I think this is surprising for the cost, at the time mine was $69.99. Most the quads I like well more in this category are either double the cost or at least $40 more.
Sorry if I am out of line.
How is yours doing after all this time, have you flown it again? Maybe you gave it away recently, I can't remember
@@jermadjesty I haven't given it away just yet. I did take it out for about a week post review. Maybe another 15 flights or so. Still flies just like it did. :)
I just bought the Flight Controller from this quad on it's own from DarwinFPV for a self build. £33 (43.19 USD) shipped from china for a 15A AIO F411 FC seems like a pretty good deal these days and sure some of the solder pads are in odd places, but so far it's just worked...
i have to say i bought one of these and i like it WAY better than my crux 35 and it isnt a spi receiver and its cheap.
I thought the crux 35 would be a fast one to fly ?
Great spending Sunday morning with you JB, nice to be back into quads again. I'm sure that cute baby is running around grabbing stuff they shouldn't by now ;) Take care.
I subscribed because of the baby ape stuff. I did NOT set up elrs and still found this video interesting/useful while I waited on shipping.
I've had this one for a while, I like it. It's a fun little drone, upgraded the camera though, in lower light the picture gets really washed out otherwise it's a lot of fun to fly and I'm not too worried if it gets wrecked.
Hey Joshua, There's an excellent double sided tape made by Gorilla Glue that is already double the thickness of the Scottch brand and holds 35=38 pounds per square inch. really sticky and squishy. I used it to hold my Crossfire Diversity and have had many hard crashes and has never come off. $3.00 a roll at Wal-Mart.
I'm familiar with this Golilla tape stuff and it's super good and sticks like shishkeebab to a freshly ironed duvet cover 😃
@@wearemany73 ive been using "Alien Tape" and its insanely sticky
If you're using dshot beacon instead of a beeper you might want to increase the Beacon Tone value so it's a bit louder. It looks like it comes set to 1 by default. I usually set mine to be 3 or 4 and then test it to make sure the motors don't heat up too much. Also if you're going to arm your quad and spin the props as a means to find a lost quad, then I recommend doing it with turtle mode on. That way you can just leave the quad armed and wiggle the stick periodically to listen for it. If you're unable to takeoff then there is a good chance you have obstructed props, so it should be a lot easier on your ESCs. If neither of those are loud enough to help you find it, then I like to put a single patch antenna on my goggles and use that to figure out what direction the signal is strongest. That usually gets me close enough to hear the props spinning.
I've been enjoying the beginner themed content lately. Can't wait for the review to come out for this.
i watch your video even though i already know what your teaching. just because i like your videos. Blue tack is god sent! must have
LMFAO @ 9:57 - "I'm gonna fly - I'm not gonna drive a tripod in the sky" 😂😎
just got one of these to learn the hobby. THANK YOU! you alone helped me jump into fpv.
10:00 that is gold, tripod in the sky🤣🤣🤣🤣
Check them out in the past, but wasnt sure what to think.
I was a little skeptical about this quad when I saw it a little while back especially when I saw the motors they look antique to me and I'm a newb!!!! Lol however I do love the price and overall it's not a bad quad....now I'm really stoked on getting it having these step by step instructions on getting it set up just sold it for me JB THANKS👍 can't wait to see you rip it✌
They look ancient because they are the motors off the original babyhawk from emax that was probably released like 4-5 years ago. They work fine though.
I sand the carbon a little bit before I use mounting tape works really well
You are gonna run out of videos- this is basically a reference guide to how to search your channel. Nice!
My baby ape pro just arrived from RDQ .
THANKS
That board layout always intrigued me - seemed like a good idea for an AIO to take the idea of the F3 ESCs and have two boards combined
It's funny that your three pads for sbus is presoldered, because mine came with a pre installed wire.. although the connector is not needed, so I'll be snipping it off
"Tripod in the sky" that's a good tagline😄🤣
Thank's for the translation ! I like looking the middle of the screen sometimes haha. I just received mine hihi... Good video again, thanks a lot !
"I'm not gonna drive a Tripod in the sky..." Hahaha. New quote for the wall?
The bubble on soldering vs. DJI made me laugh so hard! Great tutorial. Thank you and long live DIY analog!
Just bought one.... £61
Got a Ant camera ready to upgrade it.....
May even hdzero it after a few months on analogue
I'm something new and you are going to learn joshua bardwell today! Great contents as usual good sir!
That bit at 9:33 was great usually your on the dad joke level but I loled at that thanks JB
I'm not sure if JB properly realises just how funny he is. "Okay..get your hands off me!" 🤣
I install ELRS on all my new quads!
I got one of those, unfortunately that AIO in it is not that great. The boards have really weak voltage converters on them. First board I had smoked out right away on 2s, and the second one I had that came in the Ape died after about the 10th flight, again it was the converter.
Yup, you get what you pay for! I too used to buy this junk... Learned my lesson... Ain't so cheap if you only get 10 flights out of 2! 🥴
i have gone through 3 of those boards. fire hazard.
Thanks for this JB. Appreciate your help 👍
This one's gonna be my first outdoor unit. I'm going to replace the VTX with a Happymodel 300mW VTX/ELRS receiver combo, and I'll be upgrading the VTX antenna with a HGLRC lolipop. I have a set of LDARC 1104 7500kV motors on hand that I'm thinking on installing. Stoked to get outside and not have to worry about range issues.
Hii did you install the 1104 motors 7500 kv??. I think to install the same motors.
If installed how it works. Can fly with 1s?
How are compare with stock motors??
@@stelic9515 Unfortunately, the mounting holes don't match. And no, it won't fly with a 1S, even with 7500kV motors. I think you'd need at least 12000kV or better.
9:24 Those wire leads are scary long next to the pad size. That's one reason I don't like soldering to the micro pads on the micro builds.
There is a broken resistor left to the SBUS-Pads (that thing with 4R7 imprint), wonder if that could possibly cause problems!?
Nice catch! I wonder if something about it doesn't work.
That's the problem with ALL of the parts used in these ultra cheap ass quads! They use very old parts no one uses or wants anymore! They have issues and burn out quick. Buyer Beware! 🥴
I was searching the comments for someone else who also noticed this. Its a regulator i think and its been crushed from one side.
Excellent as always
Thanks,nice audio.
Just bought me one on your site 😁. Looks like fun to fly.
Danke! Thx beste Erklärung hat mir sehr geholfen....Best wishes from Germany 👌🤪👍
whats wrong with me... I just watched this video all the way to the end with no desire for this quad.. still good info as usual from Josh. 🤣👍
Tripod in the sky🤣, built not bought is the way to go!
excellent quad out of the box durable and fast ant cam is the only difference between pro
i been flying one of these on 3s for 2 months and crashed the hell out of it in trees, concrete, buried it in sand. its a fuckin trooper! the only thing that happened to it is the camera came loose from its 3d print. a motor eventually came loose after lots of crashes and flights and no maintenance and it cause the props to cut the wires. upgraded to 1204 5000kv and thing flies soo good.
Yeah, but don't you see... Once you put a dime into upgrading or repairing this hunk of junk, you might have well bought a quality, name brand quad, and had better performance from parts actually used in this decade, and you'll have long life and possibly no failures from a name brand! And, you maybe have to add 20 bucks to the cost of this Total POS! 🤔👍
Go ahead, buy it, and find out what I've already learned! Just trying to help you not throw your money away. Because that's what you do by buying this ultra low end garbage! 🙈🤮
@@KOrnhOliO1 as much as ive flown and crashed this thing without much problem im more than satisfied with its performance and durability. i was expecting much less
@@djrodriguez6582 You're a lucky guy! 😎🤘
im kinda not confident about those hole not made well to receive screw from propeler... its like my 2.5 inch 2s 8700kv eat 27 amp total... if the prop dont have screw it fly off... ... surely there is on thingiverse some print to make to put on the top of the motor put screw and with new hole for prop screw to fit (kinda need short screw .. but 2 time 3 turn of screw in pla should lock it in place ... )
That double sides stuff sticks better if you just press it firmly for 10-15 seconds. If you wiggle it won't stick as well. At least in my experience and what the instructions say on the stuff I use but you are using a different kind than I use 😆.
I had the Ape for a week and its great, XLRS is my choice to so now this is my favorite 3 inch , 80 buck delivered to europa is a bargain.
got the 129 gps long range to and the quality is way better than eachine's, so far the Darwin company has not disappointed
Well, in my 1st FPV quad and I built it myself, cost and nerve I got my self into, I asked my self that same question but my brain respond was 9:56
Funny camera moment at 9:45 mins in 😆
JB, the best!
Well great tutorial! Just dont let this be your first drone if you have bad eyes lol...i will be buying theG1600 microscope,i seen 1 of your vids with same ish version dont think this 1 was released yet.anyway,cheers for the video!
Does this tutorial work with BabyApe Pro V2?
"why dont you just get a DJI.......SHUT UP!!!!" I DONT WANNA FLY A TRIPOD IN THE SKY..." HAHAHAHAHAHA OMFG THIS HAD ME ROLLIN!!!!
6:38 Did you notice you had a broken coil (4R7 marked SMD) on your FC? We don't see that often. This thing must have taken a serious hit.
He is cute. And the video is great as well. Subscribing
Hi Joshua. I'm a fan of your channel and I love how much knowledge I learn from you. Thank you.
So I'm just about to purchase a Baby Ape Pro V2 ELRS from RaceDayQuads and I really want you to get the credit. I see you have a link to it above but I want to get the Pro model instead. Can you please give me an affiliate link to that drone? I'm not sure how that works. I'll probably also buy some batteries and a charger. I hope you'll get credit for that too.
3M Scotchfil! Damnit man, get a sponsorship or something.
Thanks a lot JB. I'm going to buy two of them just to practise without a fear.
Buen vídeo estoy por comprar el pro, pero no sé qué batería sería mejor?! La 3s de 11v verdad, el conector es el xt30 o xt60?? Puedo poner una de 1500mah?!? Gracias
I got one of these and have gone through 3 receivers. 2 brand new and one removed from a working drone. Two were betafpv mini elrs and one flywoo one. All with the tower antenna. The first one stopped working while trying to flash it. The second one did similar. The third one I took from another working quad. It worked for a minute. Long enough to bind and arm the quad. The next morning I tried it and it just lights up solid but has no connection to the controller. I have it hooked to the 4.8 v vcc, and the rx and tx both have around 3 v. I’m at a loss here and don’t know what I’m doing wrong
Needs to be on 5 volt
dam.. i'm going to have to buy one now!
Awesome, Joshua! 😊
Looking forward to the review!!!
Stay safe there with your family! 🖖😊
I have started to use only 3 wires on my ELRS rxs, as I don't need telemetry send back to my transmitter.Flying FVP, all needed info is to be seen in the OSD anyway.
Сэкономили несколько миллиграмм?
Hey dude nice video ,buddy I'm got a problem I think , my video signal I've lost over 10mts , so I think that the power off my vtx is low ,how can I change it ? I bought the darwin baby ape V2 ,tks for all
I think they tinned those pads since SBUS is so common. Mine were pre-tinned, same pads. Or maybe they just test it real quick with an SBUS RX. Not a returned unit I'm sure.
Can we install GPS?? Together with ELRS. I saw it have 2 uarts
Thank you for share your experience with us
I have a Spektrum Tx and a Spektrum satellite Rx. Will the DSM2 satellite Rx work for the Baby Ape?
Can I use the fly sky transmitter with this drone?
Hi sir.. Im from malaysia.. Can you make a complete video for install gps module and smart audio also how to activate softserial for babyape pro? Sorry im new on fpv drone.. Also how to setup in beta flight.. Please sir help me
why would you want a GPS on a freestyle quad?
Awesome video brother
Hi Bardwell, thank you for all your vids, you're helping me a lot!! theres is just one thing with the darwin drones, i always have problems with the vtx! when i install my own all is working fine, but the normal vtx from darwin is so strange! i have problems with the powervalues and levels and low power disarm mode! it's just not working when i start the drone sometimes the power ist set to 200 and somethimes to 600 but never 600 as i've set! and low power disarm is not even working (sometimes it works) and when i got the drone, the osd was so laggy, so i needed to cut some tasks in the CLI, do you know if a firmwareupdate might fix the issue? i have betaflight 4.3.1 and i don't know if its safe to update the vtx! this is my second drone from darwin and i had the same issue till i replaced the vtx myself
I can't find a link to the controller in the description
difference between ELRS receiver and r81 receiver??
ELRS uses 2.4 GHz LoRa and can go 10's of km. R81 uses 2.4 GHz FSK and can go maybe 2 km.
I am trying to use flysky fs-a8s v2 receiver any video for this ?
Hi all please help me i buy rafiomaster pocket i have receiver elrs nano 2.4 and i have problem my rafiomaster pocket My remote doesn't respond on the receiver tab, even though I've set everything up correctly
You are awesome 😎 dude
I want to run props out. How can I change the settings of the ESCs? I am still running 4.2.5 version. Thank you in advance.
Hi. Just received my BabyApe Pro. Aside from the rubber band, I didn't receive any other battery strap. What other strap did you receive? I saw two short velcro straps in the box, but they are too short to hold a battery. Cheers.!
Please unprivate your video "inverted pitch is dumb and you are dumb if you use it", it was hilarious and really helped convince me to abandon trying to control quadcopters like an fps. Maybe at least give me access? I promise I wouldn't reupload or anything. :^) Just would like to show it to my bro.
Hey dude nice video , so man I hust got a quad like that and I need I hand if possible I'm noob , I'm losing the video signal over 10 meters way I'm trying to change de vtx power but I'm not getting successful,could u help me pls
do you need a special charger for the baby ape
how do you learn to solder???
Fly quadcopter🤣🤟👍
where do i solder the ibus wire for a flysky reciever
Thank you so much for putting up this video, I finally got around to soldering my ape on friday. Quick question? is it normal to have only 6 or 8 ft of range before video cuts out to static?
Ive havent been able to fly this ape, could EP2 be interfering with video signal?
im using true patch and axil omni on skyzone 04x V2 googles.
Hello, quick question what receiver should I buy to pair it with my DJI controller 2? I really want to by the darwin Baby Ape pro. Thanks!
May i know is it possible to convert analog darvin fpv baby 3 inch to dji digital system ?
Thanks Joshua I'm new and just got this quad I have to put a dsmx receiver on this don't really know we're or how to do it any help would be greatly appreciated
i see the secret sauce....
... them motors.
If they work, i guess it doesn't matter if they look like they were ripped out of an old floppy drive
canthis thing lift action cam and whats the flight time??
they currently sell whole kit for begginers for less then 200 quit
No vuela?
Would rubbing alcohol damage the carbon fiber? If not it would help the sticky tape to stick.
hello, I really need this OSD file and it's not opening in pastebin. answer please thank you
How would you make the camera digital rather than anaglog?
hey JB, your OSD setup list needs to be updated. There are about 50 settings throwing errors in the latest BetaFlight build V. 10.9
That list is for 4.3 not 4. 4.
Hello, just found your channel and I'm considering buying the Baby Ape Pro! I just noticed they have kits on their website with controllers, goggles and all that. Would be really fun to see you do a full review with their ready-made kit to see if they're anything good to have or not :)!
Did you buy one ?
Спасибо за информацию!
How do you connect ibus receiver