Walther PPQ Q5 Match/PPQ M2 Complete Disassembly & Assembly
ฝัง
- เผยแพร่เมื่อ 16 ต.ค. 2024
- Doing a complete Disassembly on my walther ppq Q5 Match. This is a full Disassembly, difficulty level about 3. This will also work for the regular PPQ m2, q4 navy and other variants.
I meant slide lock around the 8:00 mark not takedown lever, I said it a few times on accident.
Hope everyone enjoys. Sub for more Disassembly videos. If you want a certain gun featured let me know and maybe we can put it together for you.
Follow me on IG for upcoming videos- / theshooterstable Get Protected, Sign Up With Aura 2 Weeks Completely Free with my sponsor
aura.com/thegu...
Thank you bros you saved my life that small piece fell and you addressed it in the video. Good stuff.
He blew through how to take the slide off and that's all I wanted to see.
yup...that was the most important part.
Good video but man you make that extractor look difficult lol....its actually very easy with proper technique. get your extractor in place then push plunger down and get extractor partially pushed in. Then push down safety block and snap extractor in place all the way until plunger pops into its hole. Hard to type instructions for it but basically you dont need to push safety block and plunger down at same time while you try to push in extractor...that would take 3 hands as you noted. You can push plunger down, get extractor in part way to where it will stay without holding it, then push down safety block and snap extractor the rest of the way in....if that makes sense. Not knocking your technique, just trying to be helpful. The ppq or in my case, Q4 sf is one of the easiest pistols I have to completely disassemble.
Great video, helped alot. My only issue was that little spring and getting it back in place. I didn't have a slave pin so after a few hours of almost to the point of going insane. I actually used a piece of sewing thread. Fed it through the spring and it held it in place perfect.
Well that was a great idea, glad you got it figured our
Good video! When I took my extractor out I launched that detent across the room 🤣. Just got a Q5 Match the other day, it was a used trade in at my local gun store but it was incredibly dirty. After cleaning it the trigger was very heavy and gritty. I cleaned the striker and striker channel and sprayed brake cleaner all over the internals then wiped it down with alcohol so it was bone dry. All the crud is gone but the trigger just feels heavy and staging just as it’s contacting the firing pin block on the rail. Smooth take up again after cleaning but it’s a little heavy yet and staging feel just before the break. Any ideas? Do I just need to lube it some more?
Make sure all the springs are in correctly and not binding anywhere
Just changed the trigger on my Q5 SF PRO with the Walther Dynamic Trigger. I’ve never had any light primer strikes until doing that. Had probably 8 out of 160 rounds. What would you suggest?
Great video!
Thank you for your video. It was a great help!
Thank you for watching glad it helped
Thanks for a great video - liked and subscribed! I would like to do a complete disassembly in order to clean everything after putting more than 5K rounds through my PPQ. Question: when you reassemble do all the parts need to be perfectly dry or you should apply a little bit of lubrication? Thank you in advance.
Great video...thanks so much! These are the best how-to gun videos I've seen so far. I just wish it was this easy for me! :-) Keep up the good work!
My friend reassembled her q5 but she’s got a dead trigger. Any idea what she might’ve missed?
Either the sear isn’t back in right or the trigger bar isn’t in the right position, easier to start with the trigger bar. Should be able to take the rear pin out and lift up the housing and make sure the trigger bar is in properly.
@@TheGunBench So I believe she had so much trouble with the rear pin, she never removed the trigger group. Thanks for the reply.
Question. Do I have to remove everything to clean it
No you can just use tooth brushes and qtips to clean and get in harder to reach areas
No you do not
How about a disassembly of the PPQ Sub Compact slide.
Should be the same disassembly as this minus the optic plates
Sub compact has a totally different stricker. SC has a dual spring module. It is best to replace it as an assembly. If you want to see a very detailed and much more complete take down go to the Walther site. They have a series of about 8 YTvideos.
Had to use another video to see how to take the slide out...
Thanks
If I have seen that trigger option, it has more finger support surface, but it does not solve the trigger weight of 2.5 Kg.
Replacing the trigger recovery spring, the original one with 1.5 kg, which I have already replaced, I thought I would lower the trigger weight to 1.5 kg, but I have not noticed the difference in trigger weight, only in the trip before the shot.
I do not speak English, it may not be well understood.
Goodnight:
Does anyone know how to reduce the weight of the trigger of the Walther PQ5 Match, from 2.5 Kg, to 1.00 Kg?
I already replaced the spring that performs the recovery of the trigger, that first displacement has decreased the weight, but the shot continues to be 2.5 kg.
Thanks to who gives an answer.
Unfortunately there’s not a ton of aftermarket options for the Q5, you can look into an apex trigger, from what I hear it makes the trigger pull loads better
Ugh screw that, the trigger is already one of the best - I've put a ton of rounds through mine and every now and then if you're not 110% focused you'll get an early shot. More my fault than anything, but NOTHING I've ever experienced on a pistol before. DAMN I love the PPQ match / polymer. Some day I'll save up the $$$ for the SF.
What a cluster fuck and a direct copy of a Glock only 100 times more complicated .
Very good:
Thank you!
I can not get that slide stop pin out for the life of me
Just make sure you aren’t blocking it from moving from the other side, and knock it out from the right side. It shouldn’t be very hard
The Gun Bench yep I’m knocking it from the right sized with the right size punch it’s just being stubborn.
Yeah mine is definitely in there tight! I knew I wasn’t the only one.
How???
didnt even show me how to remove the slide
srry, you works to fast. It's not easy to see and learn.
Too fast lol
Yeah it’s either too fast or too slow honestly. I can fly through some of these so i don’t think about it like I should
Stupid FN video I we're googling how to disassemble why the hell do rip off the slide without show how to release..waste of time
because I make complete tear down videos, if you can't do a field strip then my videos aren't for you. Read the manual,