सर जी आप एक वीडियो पीसीबी के टोटल फाल्ट और उसका सलूशन के बारे में बनाएं चाहे वीडियो जितनी भी लंबी हो मैं उम्मीद करूंगा कि आप बहुत जल्दी इस पर एक वीडियो बनाएंगे धन्यवाद
Hello sir mere pas microtek eb 700 inverter hai jis me charging eld still hone par bhi battery charge hoti rahti h or fan continue run karta hai ye Kiya fault hai sir please reply
Your presentation is very good. My request is that microtek inverter having same board with ic 4n35 charging current does not cut after full charge battery. Replaced bt139 but problem is still there. So please guide
1st of all thank you !! Note - 4n35 is used for change over not for charging Please check your charging section Lm324,ne555 R22 R23 Tcnl100 And check properly if your battery volt around 14.2-14.4 chg. Amp going down near 4-6 amp after some time is 0 amp. If chg. Amp. not going down then you have to replay R23 (10k ) and you have to adjust charging preset 🙏🙏
Sir mere pas microtek inverter 1115va e2 puls model h... voltage fluctuation bhut ho rha h... or voltage b khuch drop ho rha h... Sir please btay ki kya kya or kha kha problm ho skti h... mane aapki videos b dekhi h... aapki video me jo jo aapne chige btai wo to thik lg rhi h... par fir b fluctuation ho rha h.. drain wire Puri tight hai.. or hit sink b propar sahi lgi hui h... eske alawa or or konse component me problem ho skti h... please btay sir.. fluctuation ki wjh se mobile charger bhut kharb ho rhe h
Thank you.. Sir mera Microtek UPS me challu kate hi EK lamba Beep sound ake band hota hai.. aur aggar Main supply diya to tak tak relay switching ki sound ati hai.. kya fault ho shakta hai?
Sir, microtek 925E2+ ka pcb hai fault nahi nikal parhahu . ups mai ok but mains detahu to chengeover reley on off hota hai or Ic se charging pulse kum jada hoti hai
Hello sir Microtek 860 eb main par fuse blown and out put Flickr a rahi hai. Vr 1 vr 2 4n35 Diode 4007 . R17 R21 c3 really drive wali zinr 18 v and 4007 . Tr 100 lm 324 chnge kr dia h but few hour k bad problem same again show hoti hai . Micro ic ki pin no 2 par battery model par 2volt ane shru ho jate hai . Bar bR chnge k bad.
Sir help pls Microtek 1400eb 24 volt me drive okkk hai MOSFET num irf 540 n drin par volt dono par seme volt nahi aa rahe hai is karn MOSFET ud jate hai bar bar please find my problem 🧐🧐🧐
Old model pcb h to load resistance ko resold kijiye .. Mosfet check kijiye drive shi kijiye Fuse blown k liye 4n35 or diode dekhiye Or new model h to drive se hoga problem
Sir, main section mein transformer se lekar output tak pura samjha dijiye ki kaun di relay kab operate hoti hai aur voltage kahan se kahan travel hote hain.
I have got fault in microtek 850eb old model iinverter is ok but indicator is not glowing other all indicators are glowing only inverter on indicator is not glowing fuse I chicked it is ok what is the problem pls give me solution
sir 24v pe bhi koi video bnaaye. ups on ki prblum pe. mere invertor me ye hi problem ho rhi h.. iski micro ic ki pin no.1 pe 20v aarhi h.. please sir halp. ..
Inverter house नमस्कार मैंने microtek msun solar inverter 48v 3kw लिया है ,बैटरी कनेक्ट करते समय टूल से शार्ट सर्किट हो गया ,बिजली कटने के बाद टोटल inverter बंद हो जाता हैं ,बैटरी पर नही आता है, क्या कारण है, कृपया बताने का कष्ट करें,।
Old wali 4n35 us PCB Me mains par kit kit Cheng over on off hoti hai pic pin no 22 par 4.28 volt mains par change nahi hote jo 3.2volt hone chahiye thae par nahi hote hai please help
My dear i replaced lm324, 555 cn100 and triac Bta139, but current does not come to zero and charging indicator stops blinking but current remains 10Amps .when AC mains is plugged out then current becomes zero but then slowly current starts to increase again
Bahut hi badiya... Sidhe point to point without timing waste
ap jis tarike SE batarhahen kobi anzan Banda samajh jaega.verry verry thanks.
aap ka video bahut aacha laga ham ko .isi tara aaha aacha bhejiaga thanks.
Thanks
Bahut achhi video lagi sir ji
Sir exilent video koi jawab nahi
Good one.Tip Top Electronics
Bhot achi vidio h sarji
Sir pure TH-cam per Microtek new model pcb ke full falt and solutions nahi hai,, aap is per details mai video bna dejay
कति मस्त भाई।।
Sir Luminous 875va inverter me maicrotec 900va Ka cards instol Kar sakta hai please help me sir
सर जी आप एक वीडियो पीसीबी के टोटल फाल्ट और उसका सलूशन के बारे में बनाएं चाहे वीडियो जितनी भी लंबी हो मैं उम्मीद करूंगा कि आप बहुत जल्दी इस पर एक वीडियो बनाएंगे धन्यवाद
पीसीबी में लाइन और बैटरी काम कैसे करता है कृपया इस पर भी एक वीडियो बनाए और विस्तार से समझाएं कि सर्किट काम कैसे करता है आपकी महान कृपा होगी
Good tiching 👍👍👍👍👍👍👍👍
Thank you sir hi same achha smjhaya.
Thanks
Sir new inverter ka ups mode on nahi ho rha kya problem ho sakta hai
bahot nice brother, pls bring other brand troubleshooting also. and put videos little early. thanks alot
Thanks , give me some time 😊
Hello sir microcontrolar Cheng kaise hoga kya micro can. Market me milta hai
Market ka pata nhi
Agar chahiye to apna contact share kro aap
May contact karunga
Bro mere 875va microtake sinevave h usame power on off switch ke pas bulb on karane par jalta nahi hai solution bataye
Sir eb 600 ka fuse blow indicator kabhi kabhi on hota hai par kush time bad off ho jata hai kya problem hai
Sar mosfet ke pass resistor kitne number ki hoti h bare wali 7805 ke pass lagi ho h
Hello sir mere pas microtek eb 700 inverter hai jis me charging eld still hone par bhi battery charge hoti rahti h or fan continue run karta hai ye Kiya fault hai sir please reply
Your presentation is very good. My request is that microtek inverter having same board with ic 4n35 charging current does not cut after full charge battery. Replaced bt139 but problem is still there. So please guide
1st of all thank you !!
Note - 4n35 is used for change over not for charging
Please check your charging section
Lm324,ne555
R22
R23
Tcnl100
And check properly if your battery volt around 14.2-14.4 chg. Amp going down near 4-6 amp after some time is 0 amp.
If chg. Amp. not going down then you have to replay R23 (10k ) and you have to adjust charging preset 🙏🙏
Hii sir kiya app har brand ki inverter service you tube daliya sir
Sir mere pas microtek inverter 1115va e2 puls model h... voltage fluctuation bhut ho rha h... or voltage b khuch drop ho rha h... Sir please btay ki kya kya or kha kha problm ho skti h... mane aapki videos b dekhi h... aapki video me jo jo aapne chige btai wo to thik lg rhi h... par fir b fluctuation ho rha h.. drain wire Puri tight hai.. or hit sink b propar sahi lgi hui h... eske alawa or or konse component me problem ho skti h... please btay sir.. fluctuation ki wjh se mobile charger bhut kharb ho rhe h
Beautiful video sir
Thank you.. Sir mera Microtek UPS me challu kate hi EK lamba Beep sound ake band hota hai.. aur aggar Main supply diya to tak tak relay switching ki sound ati hai.. kya fault ho shakta hai?
Sir g eb 1100 m main Dene par main sence kar leta h par out put band ho jata h or charging bhi nahi kar h
Sir, microtek 925E2+ ka pcb hai fault nahi nikal parhahu . ups mai ok but mains detahu to chengeover reley on off hota hai or Ic se charging pulse kum jada hoti hai
Bahut din bad Aaye ho Bhai
Haa kuch busy tha .. 🙂
Hello sir
Microtek 860 eb main par fuse blown and out put Flickr a rahi hai.
Vr 1 vr 2 4n35 Diode 4007 . R17 R21 c3 really drive wali zinr 18 v and 4007 . Tr 100 lm 324 chnge kr dia h but few hour k bad problem same again show hoti hai . Micro ic ki pin no 2 par battery model par 2volt ane shru ho jate hai . Bar bR chnge k bad.
bhai dusara PCB ka jo dt modal hai uska plus check kaise kare bata do plese plese
Good Bro 👍👍👍🙏
We have microtech EB 900 inventor it’s some resistance burnt R60,61,62,63 76, can you explain me what is this resistor value
Good Sir good job
Sir help pls Microtek 1400eb 24 volt me drive okkk hai MOSFET num irf 540 n drin par volt dono par seme volt nahi aa rahe hai is karn MOSFET ud jate hai bar bar please find my problem 🧐🧐🧐
Nice information 👌
Thanks
Good sir ji
sir mera ups microtec 850SEBZ sine Wave hai isme {over loading & fuse blow} ki problem hai kaise sahi hoga
Old model pcb h to load resistance ko resold kijiye ..
Mosfet check kijiye drive shi kijiye
Fuse blown k liye 4n35 or diode dekhiye
Or new model h to drive se hoga problem
Sir, main section mein transformer se lekar output tak pura samjha dijiye ki kaun di relay kab operate hoti hai aur voltage kahan se kahan travel hote hain.
Sir mere paas Microtek 1000eb model hai, uska buzzer nhi chalta or out put volt 165v nikal raha hai, please help me, thanks
Good Info sir
Sir ji 850EB old PCB me fuse fallt aa raha h plz tell me
PCB me mains on karene ke 5 second baad me fuse उड़ jata h
Plz tell me problem shortout
Sir 83202 ibz driver ic milaga kya
Apne najdiki market me pata kijiye milta sab h
Bhai pf nahi mov hota hai high voltage par blast hona uska kaam hai
Sir sab kuch thik hai charging relay bhi change kr de but charging show krta hai apm nhi ate
JM1250 EB inverter kit lena hai
Sir, Pcb Bod ketne me melts hai
Nice
@@SK.subham ok
Good 👌
Ups mode p 250 v aa rhe h par lose lagane par voltege drop Ho jate h to kya kare es p koi video bnaye
New pcb me priset nahi hai lekin betrry 13.2 tak me hi charging cut of ho jata hai isko 14.2 tak me set karna hai kaise hoga
Sur g charging ane k baad humming kar raha hai or transformer magnet bana raha hai or cn100 kut ja raha
Solf kare sur
Main off karne par output par dim bulb jalta hai kahan problem hai?
V good
Mere invatar ka capesitar our mosfet jal Gaye ase kiu hota Hain please bataye
sir pin 26 se charging pulse nahi aata hai
Explain is too good
nice
Can you please add the link where we can purchase the old type PCB board for 800 va Microtek inverter old model.
Ser mere pass microtak12v PCB tansfarm wali h isme main a rhi h lakin batt.charging nhi ho rhi h
Sir charging cat k liy pirates lga sakte hi
Blue wali charging cut ki hi preset h
Cn 100 ki जगह kon sa transistor lagaye
Sukam 24 volt ki charging tracking bhi batao bahut pareshan karti hai
12/24 same hoti h
Sir plz mere pass transformer wala PCB hai trasfarmer teek hai change ver nai hora kyu pls
Sine wave ke baare me bhi video banay
Jaldi hi
nice video
I have got fault in microtek 850eb old model iinverter is ok but indicator is not glowing other all indicators are glowing only inverter on indicator is not glowing fuse I chicked it is ok what is the problem pls give me solution
sir 24v pe bhi koi video bnaaye. ups on ki prblum pe. mere invertor me ye hi problem ho rhi h..
iski micro ic ki pin no.1 pe 20v aarhi h..
please sir halp. ..
Good sir
Very best sir
Mere inverter me charging full show karta hai lekin betry charge hoti nhi hai kya problem ho sakti hai
Sir mera Microtek 860eb led not working one led working ups on led please help me 😭
Vishal ji 500 w load main kitne dc ampiar hote hain
12volt me 45-55 amp. Jaayega
Super
Good yrrr tnq
Dono PCB me kaun sa achha PCB hai
Inverter house नमस्कार मैंने microtek msun solar inverter 48v 3kw लिया है ,बैटरी कनेक्ट करते समय टूल से शार्ट सर्किट हो गया ,बिजली कटने के बाद टोटल inverter बंद हो जाता हैं ,बैटरी पर नही आता है, क्या कारण है, कृपया बताने का कष्ट करें,।
Old wali 4n35 us PCB
Me mains par kit kit Cheng over on off hoti hai pic pin no 22 par 4.28 volt mains par change nahi hote jo 3.2volt hone chahiye thae par nahi hote hai please help
1k or 2k preset ko change kro aap ..
Or 2no 2k lagaoo aap or ache see adjust kro aap ...
exilent video
Sir if main controller is bed so from where I can get new one my inverter main Ic model 600eb . pl.explane thanks
At company service engineer or who has consult with company member
Very good sir
Sir aap kha se ho
24 v. K bare me detail de sir plz...
microtech1250 jambo me on karne par falt/battery wala led glow kar raha .aur output nahi aa rahi .bataye kya kare.
led red glow kar rahi
Microcontroller kahan se purchase Karen
Pcv ka price kitna hai sir
Sir good video
Sir spar pat apke pas melega kia
9937656930
Sir ji battery ki wire ulti lg gyi kia kharab hua h
Plz help me
90% case me DC fuse hi kharab hote h or Baki parts safe rahte h
@@inverterhouse9077 sir ji us me mota(mera Matlab wire ka fuse lga rakha tha) Jo nhi uda
Us me se dhooaa nikla kafi
Sir ji hlp me plz
Mosfet burn huwe ho sakte h
Phle check kro aap open krk usko
Mast but aaj eak micro teck ki charging repair karke dekhta hu jo kai dino se hi amp de raha hai
Ok
Scr/triack ya Lm324 ka fault hoga
sir mane ic kaha se buy karte hai
Send you contact no.
Sir mene dino ragistense dono 4n35 lm324 or preeset check kr llya pr change ower nhi hi raha
Preset ache see adjust kijiye ... Or aap micro change krk dekh lijiye
Chota Bala driver transformer jo tric ke pass hai use check karo aur tcnl 100 transiter ko check karo
Change over me iska Kya Kam h Bhai Jaan ? Jara explain krenge
Sir mera new modal invertel h kat kat kr awaj karti h change nhi ho rhi h
Konsi pcb h
Kb aawaj kr rahi h ..
Microtek 785 e2 Jo line deta hun to kat kat krta h awr bzer bjta h.charge nhi hoti h
Ic Marketa MA to mela hi nhi rhe ha
Market me na milta h aasani se ..
Mere microtek 875 me main line lagne pr bhi kuch light nahi aa raha h
My dear i replaced lm324, 555 cn100 and triac Bta139, but current does not come to zero and charging indicator stops blinking but current remains 10Amps .when AC mains is plugged out then current becomes zero but then slowly current starts to increase again
When battery volt is around 14.4 volt then check and inform Battery volt ..
Sir squr wave charging amp not incresing
Sir 4n35 mil jata hai
Bhai Mera inverter backup ke time low output deta hai what can I do
Inverter kit kaha se milega
Charging transistor nahi ho to usake jagah par kya lagaye
Bina uske chg. Na aayegi
Aapke pas ek transitior na h aishe thodi Kam chlta h
Stock maintain rakho kro agr Kam krna h to