Great tutorial. But I found it works a lot better to use fingernail clippers to cut those small nubs off the sides. And a nail file to file them down flat. 👍🏾
I appreciate the support and recognition brother. I have been watching your videos on TH-cam even before I got started with custom products and supplies. 💈❤️💯
Thank god I found ur youtube channel! I'm lefthanded and I prefer to learn from lefty's. I'm in my last year in barber school and not looking forward finishing yet .There is still a lot to learn. If you would like to chat or something , would love to show some of my work and see what you thing. Much love
I want to ask you something. I got my andis slimline pro li out the box and I started to make my 1st guideline with bulk thick hair. Started to cut and then blade just stop cutting like it dulled out. Motor spinning and blades moving. Is that possible that a blade can just dull out like that? Thank you.
Dope tutorial but today I was cutting and it made a weird noise so I checked my trimmers took then apart and the metal clip that holds the little black box it broke, what could i do???!!!!???!???
Yo Nail clippers and a metal Emery Board to modify the blade holder pimp.... Thanks for sharing this video Im going to go check out the rest of your videos now....And thanks for the Hair Tailor recommend I'm going to send some clippers out to him ASAP
Hey i did that and my clippers when i turn them on they do this noise like something is clashing inside them and i try to cut hair and cuts nothing... do you know what is it?
My trimmers dont sound as strong as yours. If I tighten the blade down too much, it sounds like it’s struggling. If I loosen it, the blade starts to wiggle. Any advice?
I have the same issue! Sometimes the trimmer won't turn on unless I loosen the screws. Another thing, the 2 top screws don't seem to align perfectly to the holes, they seem to go in a bit diagonal. Did u find any solutions?
Cristian Negron 8:48 from this part on. Pay close attention on how he sets those screws. They need to be to sit flat. Make sure your holes are drilled correctly. At first and my screws weren’t set correctly so it was causing the trimmer to bog out. Every thing needs to sit flush. After making these adjustments, My trimmers work perfect, They hit hard, They are my finishers. Those 2 screws on the blade won’t look like they’ll screw in but that’s how it is. Just have to angle it a bit. Just check your setup again. Hope this helps 🤙🏾
Hi, do you know any trimmer with zero gapped and no need to any adjustments i can use it directly after opening the box? I dont want to do adjustments i want to use it directly. Thx
dinky19810 you're right, my first Li seemed solid, felt porwerful, and this new one i got seems weak, full charge and sounds "dull" if that makes sense. And i imagine with a heavier blade its all bad haha
dinky19810 actually, not really? How much heavier the the t blade bottom blade compared to the bottom blade from the original Li??? I bet its irrelevant, its the only part that moves. Your clipper is heavier, but thats irrelevant to the motor.
I got 3 pairs so i tried it and it works fine yall gotta remember the rotary motor is the most powerful of all the clipper motors turns your clipper to a cordless andis t outliner
Did it . and fkd up my slimline . Mosdef not worth . The motor isnt strong enough. I had to go back with the regular blade. And cutting the frame to make it skeleton is a bad idea as well.
You leave way to much for the imagination. When you do a how to, it's exactly that, How to. You should of showed before and after pictures of what the pieces looked like before drilling and before being shaved off. I can get it done, for these young guys that don't even have tools , there is just way to much stuff missing for them to get the whole picture. Thanks for your efforts anyways.
Agree with you. In order to do this correct I would of had to perform this perfectly while recording it. I had to do everything beforehand to make sure it works and by then either I throw the video together or buy another set of unmodified stuff to add for just video purposes and never use. I decided to save the money. I tried to put enough content with this situation so most people could perform the mod and in most cases people have done it successfully with this video. There’s no way I could of satisfied everyone given these circumstances so I will wholeheartedly agree with you. Cheers buddy
@@kikado3 No Problem, Besides leaving a few things out, you did a great job. It was the not so handy going ones, I was worried about. At least you helped out others and that is very much appreciated. Thanks again for your work.
Great tutorial. But I found it works a lot better to use fingernail clippers to cut those small nubs off the sides. And a nail file to file them down flat. 👍🏾
Great tutorial I ordered the blades and completed the mod. Now I’m hyped to see how they work.
Did they work? And if so how did they cut?
Some of the best tutorials by this man. Hopefully he comes again with some soon.
I appreciate the support and recognition brother. I have been watching your videos on TH-cam even before I got started with custom products and supplies. 💈❤️💯
Just mentioned you on my newest vid. Keep up the great work man.
I rather do this to my Slim Line Pro Li than buy the Wireless Andis T-Outliner which cost like $150
Thts exactly what im bout to do! Buy a extra pair of slimlines and modify them!
They sell the cordless t outliner for $90 over in rancho cordova
@@anthonyg_lifestyle2908 appreciate it but I tried them and I feel like they are weak
@@anthonyg_lifestyle2908 Rancho where bro?
Thank god I found ur youtube channel!
I'm lefthanded and I prefer to learn from lefty's.
I'm in my last year in barber school and not looking forward finishing yet .There is still a lot to learn.
If you would like to chat or something , would love to show some of my work and see what you thing.
Much love
I want to ask you something. I got my andis slimline pro li out the box and I started to make my 1st guideline with bulk thick hair. Started to cut and then blade just stop cutting like it dulled out. Motor spinning and blades moving. Is that possible that a blade can just dull out like that? Thank you.
No it shouldnt be halpening like that. Make sire the blade it tight on.
Is there any diffrence between the blackout blade compared to the normal version?
Man u cant u jus send ur adress and charge a fee n u do it n send it back. I gt adhd i aint gna be able to do this shit the way u explained
Dope tutorial but today I was cutting and it made a weird noise so I checked my trimmers took then apart and the metal clip that holds the little black box it broke, what could i do???!!!!???!???
The Hair Tailor is a Master
Yo
Nail clippers and a metal Emery Board to modify the blade holder pimp....
Thanks for sharing this video
Im going to go check out the rest of your videos now....And thanks for the Hair Tailor recommend
I'm going to send some clippers out to him ASAP
Two thumbs up!!! Thank you for the great tutorial
Hey i did that and my clippers when i turn them on they do this noise like something is clashing inside them and i try to cut hair and cuts nothing... do you know what is it?
Where can I get this in NYC?! Hurry!!
Ricardo the barber super fan tuyo desde Colombia America 💙👍
If i do this to my slimline does this make it better than gold fx skeleton? Can some one answer me plz thank you!
No the skeletons are way better.
@@kikado3 thanks for answering me bro you the best i just sub
@@kikado3 bro do gtx blade hit better than the skeleton fx?
Awesome thank you buddu
Is it supposed to be loud? Like louder than my wahl magic clips?
Spray them. If it doesnt change then yes they might be louder. I dont remember mine being that loud. Could be your blade placement
When im 0 gaping the top skrew moves the blade down again a little .i am.only.using the bottom little skrew to hold .what should i do
My trimmers dont sound as strong as yours. If I tighten the blade down too much, it sounds like it’s struggling. If I loosen it, the blade starts to wiggle. Any advice?
I have the same issue! Sometimes the trimmer won't turn on unless I loosen the screws. Another thing, the 2 top screws don't seem to align perfectly to the holes, they seem to go in a bit diagonal. Did u find any solutions?
Cristian Negron 8:48 from this part on. Pay close attention on how he sets those screws. They need to be to sit flat. Make sure your holes are drilled correctly. At first and my screws weren’t set correctly so it was causing the trimmer to bog out. Every thing needs to sit flush. After making these adjustments, My trimmers work perfect, They hit hard, They are my finishers. Those 2 screws on the blade won’t look like they’ll screw in but that’s how it is. Just have to angle it a bit. Just check your setup again. Hope this helps 🤙🏾
Thanks man!! I was stuck on drilling and making the holes bigger!!
Carlos Manúel that's a very good idea
Where did you get your blackout blade ?
couple years ago. loved it.
Hey I noticed u didn't use the little metal spacer that comes with the t outliner blade. Does it matter?
it doesn’t no
Probably a great video I just couldn't hear it well enough to watch it all the way through and yes my volume was all the way up.
If he say “Ahh-right” one more damn time!
Good tutorial tho.
Where I can find that exact blades?
Too bad thehairtailor.com is out of business as of 11/11/2019. Any other suggestions?
I did the same modification to my trimmers and they don’t even cut they keep pulling hair
Thx. Good video. Just got it done. Can't wait to try them out.
How do you charge for the modification???
I try it . You have to file all the way to where the spring are that make it weak and the blade twist after a few use
Are those just regular blackout blades modified
Yo Ricardo where you been bro? I will wait for you to drop a new video for long time!
Chillen with the kids brotha lol. Busy with the baby tho most of the time. I had a chance for a video today and took it
Ricardo The Barber well hopefully you find some time to drop some more dope haircut tutorial videos
Gonna try to film Sunday a low fade with long hair on top.
Great vid man
Ricardo The Barber what happen it's been about 5 months! Lol
Those are some baaaaddddddd boyssssssss
Amazing Mod RiK..
Hi, do you know any trimmer with zero gapped and no need to any adjustments i can use it directly after opening the box? I dont want to do adjustments i want to use it directly. Thx
Moon Light Yes get urself a Wahl Detailer with a T-Wide blade on it you can use them straight out the box and they are sharp
Nice My Guy
Good Job
Best of the best 💪
Like 👍
Has anyone modded them to use a SuperLiner blade? If it works LMK, I have a Slimline I wanna try to put an Andis In-Liner blade on. (4885).
Bad boy was used nineteen hundred and ninety-two times lol
And are u gonn make a video putting them to use
Yes soon. I just did them yesterday so I believe Sunday I'm filming
Ricardo The Barber cool...subscribing now
Slimline are definitely one my favorite trimmers
nick horton do they hit right out the box
sam o yeah I think they do pretty good but I got some tea outliners I don't hit for nothing
Nice video
Eehhrright! Glad to see you back bro. Will the weight of the tliner blade slug the motor much or no difference?
Yes but very minimal.
Yoooo that blade is too sharp it seems should I just back off a little?????
Great video I’m try it
My Dude... How have you been? Hope the fam is doing wonderful...
Those clipper motor is gonna overwork cause of those heavy blades. Leave it alone.
dinky19810 exactly I'm not doing to mine that is exactly what I said
+dinkly19810 That's all I've been thinking from I first heard about this... Thanks for reminding me! lol
dinky19810 you're right, my first Li seemed solid, felt porwerful, and this new one i got seems weak, full charge and sounds "dull" if that makes sense.
And i imagine with a heavier blade its all bad haha
dinky19810 actually, not really? How much heavier the the t blade bottom blade compared to the bottom blade from the original Li???
I bet its irrelevant, its the only part that moves.
Your clipper is heavier, but thats irrelevant to the motor.
I got 3 pairs so i tried it and it works fine yall gotta remember the rotary motor is the most powerful of all the clipper motors turns your clipper to a cordless andis t outliner
Now I can modify mine when I get them 😎
Did it come out good for u?
Como faço pra mim cortar a minha máquina e deixar igual a sua ?
Did it . and fkd up my slimline . Mosdef not worth . The motor isnt strong enough. I had to go back with the regular blade. And cutting the frame to make it skeleton is a bad idea as well.
been running two of these skeleton and one with the blade mod for six months and working perfect!
Bro...i can't hear NOTHING (EVEN with ear-buds in)
Followed to a T.......perfect!
Screwed mine up.. the metal piece pooped out it never zero gapped
Modified my hitters , thanks !!
Nobody say that bad boi like u say that bad boi lol
Ill take it lol
I like listening to u its cool
U from new York right for 100 buck I bet I'm right
Oh yea u use the one minute sharper on the still blade
Fire thanks
Used a gtx blade and ceramic cutter 👍👍👍
Man if u have to do all that u might as well just use the T outliner's
I can barely hear you
ill just buy a cordless t-ouliner 😐
Too much work...
Капец так режет слух твой олрайд. Что даже с середины видео включил ускорение, и смотрел без звука
You leave way to much for the imagination. When you do a how to, it's exactly that, How to.
You should of showed before and after pictures of what the pieces looked like before drilling and before being shaved off. I can get it done, for these young guys that don't even have tools , there is just way to much stuff missing for them to get the whole picture.
Thanks for your efforts anyways.
Agree with you. In order to do this correct I would of had to perform this perfectly while recording it. I had to do everything beforehand to make sure it works and by then either I throw the video together or buy another set of unmodified stuff to add for just video purposes and never use. I decided to save the money. I tried to put enough content with this situation so most people could perform the mod and in most cases people have done it successfully with this video. There’s no way I could of satisfied everyone given these circumstances so I will wholeheartedly agree with you. Cheers buddy
@@kikado3 No Problem, Besides leaving a few things out, you did a great job. It was the not so handy going ones, I was worried about. At least you helped out others and that is very much appreciated. Thanks again for your work.
Nothing crazy