I had a seized axle on the knuckle as well. I used a torch to heat up the area around the axle spline. Then pb blaster penetrating oil on both sides of the axle, and then an air hammer to knock it out. That way you don't need to pull the axle out.🌈
Glad you said automatics dont lose ATF my 2017 soul is an automatic I've done few axle replacements due to bad wheel bearings fluid has never came out.
just use a hub puller, it'll push that axle in, then put the nut back on. use the rotor on the axle to act as a slide hammer to pop the axle out of the transmission. then move hub out of the way and remove axle
Any way to do it without removing the tie rod? Maybe rotating the wheel to the left will do the trick, so you don't have to remove even the ball joint. -- What if I lift both tires? won't be easier? -- You put 100Ft-lb on the lug nuts, are you sure is that? mine is 2012 automatic and it take from 65-79 ft-lb. -- Do you think 155 ft-lb for the CV axle nut is enough? --- I have to do mine maybe 4/10/2024, grease is getting out and I don't want to waste time replacing boot when I get a brand new for $ 69 include tax and shipping. -- You know you can put the clip on the transmission site up to 12 o'clock position and it will get inside easier? --Have you ever replaced the sway bar bushing? Man, is pain in but. I don't have that rust. I live in desert heat.
th-cam.com/video/q57mlrLcYog/w-d-xo.html You will have to scroll through , near the end of the video I covered this , on the engine replacement. Thanks for watching.
I’m in the middle of replacing my wheel bearing now!! The wheel won’t stay straight though. It keeps falling left to right and holding there really tight! Did I break something?
I’ve done everything you’ve done in this video all the way up till you released the bottom arm from the wheel hub, but my wheel is turning from left to right hard! It won’t stay in the middle and it’s a bitch to move it to the middle too
The plastic cover on the transmission front. Theres a cap you remove with a 3/8 ratchet or extension end. Even easier you can hand pump it in through the check fill port below that. With it level and running it will trickle out. It only will hold about 3.2 to 3.5 quarts on a drain fill even. Thanks for watching.
Thank You so much! You were so unbelievably calm
Thank you for the terrific feedback.
I had a seized axle on the knuckle as well. I used a torch to heat up the area around the axle spline. Then pb blaster penetrating oil on both sides of the axle, and then an air hammer to knock it out. That way you don't need to pull the axle out.🌈
Great tips , thank you for sharing.
Glad you said automatics dont lose ATF my 2017 soul is an automatic I've done few axle replacements due to bad wheel bearings fluid has never came out.
Thats not the face of the bearing thats the hub,the bearing is pressed in on the back side and sealed in with a expanding ring.
just use a hub puller, it'll push that axle in, then put the nut back on. use the rotor on the axle to act as a slide hammer to pop the axle out of the transmission. then move hub out of the way and remove axle
Good job" 💥 Great camera work! 🛠
Thank you for the awesome feedback.
Any way to do it without removing the tie rod? Maybe rotating the wheel to the left will do the trick, so you don't have to remove even the ball joint.
-- What if I lift both tires? won't be easier?
-- You put 100Ft-lb on the lug nuts, are you sure is that? mine is 2012 automatic and it take from 65-79 ft-lb.
-- Do you think 155 ft-lb for the CV axle nut is enough?
--- I have to do mine maybe 4/10/2024, grease is getting out and I don't want to waste time replacing boot when I get a brand new for $ 69 include tax and shipping.
-- You know you can put the clip on the transmission site up to 12 o'clock position and it will get inside easier?
--Have you ever replaced the sway bar bushing? Man, is pain in but. I don't have that rust. I live in desert heat.
What school did you attend amigo
Is the inner tie rod bent?
Good Job
Thank you
Is this a manual or automatic transmission?
Manual , thanks for watching.
How did you fill the trany
th-cam.com/video/q57mlrLcYog/w-d-xo.html
You will have to scroll through , near the end of the video I covered this , on the engine replacement. Thanks for watching.
Ok found it thank you much
I’m in the middle of replacing my wheel bearing now!! The wheel won’t stay straight though. It keeps falling left to right and holding there really tight! Did I break something?
I’ve done everything you’ve done in this video all the way up till you released the bottom arm from the wheel hub, but my wheel is turning from left to right hard! It won’t stay in the middle and it’s a bitch to move it to the middle too
Hi where put the oil transmission
The plastic cover on the transmission front. Theres a cap you remove with a 3/8 ratchet or extension end. Even easier you can hand pump it in through the check fill port below that. With it level and running it will trickle out. It only will hold about 3.2 to 3.5 quarts on a drain fill even. Thanks for watching.
Ezcus3 me bud what did you mean with the "drain fill even"? I need to top my transmission uo so im trying to tp nine off its low.
👀👍✔