Make the Ultimate Mosaic Pin! - Knife Handle Special

แชร์
ฝัง
  • เผยแพร่เมื่อ 6 ม.ค. 2025

ความคิดเห็น • 19

  • @Every1Has1
    @Every1Has1 ปีที่แล้ว +11

    On a budget ..Brake bleeding vacuum pumps will work 15- 20 bucks.

  • @ozarked2363
    @ozarked2363 ปีที่แล้ว

    Walt's a professional. I'm a hobbyist. I just load the tube with epoxy with a Q-tip, then coat the rods going inside it with epoxy and cover both ends with painters tape. I do use the little piece of tape around the rods but I place it in the center, not on the ends. It keeps the rods centered inside the tube if they are just a bit undersized.

  • @johnvanderwalker4830
    @johnvanderwalker4830 ปีที่แล้ว

    A break bleeder pump can work too.

  • @mikeredrugger
    @mikeredrugger ปีที่แล้ว +1

    Can't wait to give this a shot

  • @sween187
    @sween187 ปีที่แล้ว

    If you do use a syringe try using a smaller volume one 1ml or 2ml syringe this way you can get more pressure compared to a 10ml 20ml syringe

  • @RinaldoFamilyMetalworks
    @RinaldoFamilyMetalworks ปีที่แล้ว +2

    Was you Kydex vacuum DIY? If so, have you made a video on that? Thank you for the educational information!

  • @danwerkman
    @danwerkman ปีที่แล้ว

    I must say...the ball bearings are a novel idea. Always innovative you are.

  • @larrybud
    @larrybud ปีที่แล้ว +2

    You also don't need to just fill the tubes with metal! Small dowel rod of your choice of wood species!

    • @ozarked2363
      @ozarked2363 ปีที่แล้ว +1

      The first one I did I used an aluminum round tube with a brass square tube inside it. I wanted something else inside the square tube and realized that a round toothpick fit perfectly snug inside it. A little black epoxy around the toothpick filled the corners of the square tube. I used the pins on a camp knife for my SIL with mahogany scales. I also once used a .223 case with the neck and base cut off for a lanyard tube.

  • @Dreweldeenknives
    @Dreweldeenknives ปีที่แล้ว

    I have a Milwaukee pump battery powered that’s a sweet tool

  • @ryanblystone5153
    @ryanblystone5153 ปีที่แล้ว

    Thank you

  • @donscottvansandt4139
    @donscottvansandt4139 ปีที่แล้ว

    Awesome stuff!

  • @xthemadplumberx7110
    @xthemadplumberx7110 ปีที่แล้ว

    Watching and I see a vacuum pump and I cringed; I’ve been through two stabilizing. My wife said I’m done buying them. I’ve been told that a brake bleeder from Harbor Freight will do the same job; I have yet to try it.

  • @billwoehl3051
    @billwoehl3051 ปีที่แล้ว

    You could thin the epoxy with acetone, but, then it would just drain back out of the tube after you took the vacuum away.

  • @andrewsteinberg7103
    @andrewsteinberg7103 ปีที่แล้ว

    No way would that work for HVAC in Ac pump downs we use two stage vacuum pumps and they’re like at least 50 pounds in weight

  • @lunkydog
    @lunkydog ปีที่แล้ว

    Looks like 1/4NPT.

  • @joeyalent4974
    @joeyalent4974 10 วันที่ผ่านมา

    I'm guessing that you can not peen mosaic pins.

  • @amaroussama
    @amaroussama ปีที่แล้ว +2

    اللهم انصر اخواننا في غزة