Worked great! I figured it out even though it wasn't in English. Here's what is happening: 0:30 Remove toner drawer. 0:39 (not shown) Remove this screw. 0:50 Remove the roller (the hinge pin unscrews). 1:15 Remove side panel screw and pull it off (yank hard). 1:29 Unlatch and pull out this white pin. You have to pull it out from the ITB pretty far, or it will catch the ITB when you pull it out. I didn't have to bend a screwdriver, I got it with a normal screwdriver. 2:05 Unscrew the rear 2 screws for the ITB. 2:25 Pull the white gear left to free the ITB. Then it pulls out. I didn't replace the ITB, I just cleaned the whole thing with compressed air and wiped the entire belt with dry toilet paper. Worked pretty good. 2:50 When sliding the ITB back in pull the white pin out if it gets stuck. 3:06 Pull the white gear left at the end of pushing the ITB in. It'll engage with the belt roller. 3:20 Make sure the white pin is secure like you found it. 3:33 Reinstall side panel (punch it firmly but not too hard, to snap it in) 3:50 Put the roller back. 4:10 Put the toner drawer back in. 5:45 I didn't have this problem!
Thanks for the explanation in English😄 Glad you didn't have trouble with the last line! I made a Japanese commentary based on the English video, but I'm glad it was helpful!
Worked great! I figured it out even though it wasn't in English. Here's what is happening:
0:30 Remove toner drawer.
0:39 (not shown) Remove this screw.
0:50 Remove the roller (the hinge pin unscrews).
1:15 Remove side panel screw and pull it off (yank hard).
1:29 Unlatch and pull out this white pin. You have to pull it out from the ITB pretty far, or it will catch the ITB when you pull it out. I didn't have to bend a screwdriver, I got it with a normal screwdriver.
2:05 Unscrew the rear 2 screws for the ITB.
2:25 Pull the white gear left to free the ITB. Then it pulls out.
I didn't replace the ITB, I just cleaned the whole thing with compressed air and wiped the entire belt with dry toilet paper. Worked pretty good.
2:50 When sliding the ITB back in pull the white pin out if it gets stuck.
3:06 Pull the white gear left at the end of pushing the ITB in. It'll engage with the belt roller.
3:20 Make sure the white pin is secure like you found it.
3:33 Reinstall side panel (punch it firmly but not too hard, to snap it in)
3:50 Put the roller back.
4:10 Put the toner drawer back in.
5:45 I didn't have this problem!
Thanks for the explanation in English😄
Glad you didn't have trouble with the last line!
I made a Japanese commentary based on the English video, but I'm glad it was helpful!
THANK YOU.. THANK YOU.. Most greatfull.. 🙏🙏🙏
Thanks for your comment.
I'm glad it was helpful 😄
ITBユニットはどこから入手できるんですか？
Aliexpressで形が同じのがあったのですが、適合するか分からず博打だったので、たまたまあったヤフオクで買いました。
@@Professor_Mori_DIY
動画、大変参考になりました。ありがとうございました。
ITBベルトが破れたために、交換しようと思い立ちました。
ITBユニットの型番、分かりますでしょうか。
mf634cdw での検索では Aliexpress しかなくて、思い切って購入してみました。同じようなものが届きましたが、ベルトが2カ所破れていて、結局使えません。返金交渉を始めましたが、春節なのでちゃんと処理されるでしょうか。
どこか他で ITB ユニットが手に入らないか探しています･･･
@@GO-RTW コメントありがとうです。
ITBユニットの型番は分かりません。僕もAliexpressでしか見つかりませんでした。
破れがあるのは最悪ですね😭
修理に出すと数万円かかりそうだし、Aliexpressのは1万5千円くらいするので、印刷部分はほぼ同じのLBP612Cの中古を買って外した方が安そうだと思います。
Nice work
Thank you as always.
Difficult to use if left broken.