Hi! Thanks so much for these videos! I've been programming for a while now but have never done anything with Micro controllers or IoT. I'm really excited! Definitely had to scrounge around for a DATA Micro usb cable... standard charging cables weren't working. Thanks again!
I have the problem it shows me: Failed uploading: uploading error: exit status 2 The power Led lights up normally as well as the temperature is warm but not hot. What can I do?
Thank you very very much for this vídeo. As a matter of fact, I have the very same Output message as you do in the end, after solving you issue : "Resetting via RST pin". I've read in the documentation that this is not a bug, but rather a feature. In any case, if the program is really being loaded, I can not see the builtin Led blinking as it was supposed :(
HI Thank you for your videos I have an error when I start to build my sketch for esp32 but no issue for esp8266 I m using windows 10 This is the error : exec: "cmd": executable file not found in %path% compile error for esp32 dev module board I need help THANK YOU
hello mr. i have same problem like u,but i still dont know how to upload coding. I was do like you do, and last statement say it is "Leaving... Hard resetting via RTS pin... " . When i get this statement, what should i do for can upload coding,please help me sir😢
I'm pulling my hair out on this one ! I constantly have th' 'No serial data recieved' error and can't upload. The only time that it works is when i completely remove the COM port device from my devices manager, reboot the computer and let it detect again. Then in the arduino software i can upload without any problem. It happens that it works twice but when it fails, i never get it to work again until i delete and add the comm port again. What a piece of garbage
Have you experienced some unprintable characters being printed before the "Hello World" is printed? It is only printing the strange characters the first time "Hello World" is printed, all following prints look as expected. If I print with an empty string in the "Serial.println("");" I see only the strange characters. Thanks again. FYI: I did also double check my baud rates were aligned at 9600.
I have only ever seen that when the baud rates are not the same. Just to confirm, are you setting the baud rate on the serial monitor itself to 9600 (bottom right of the serial monitor)? There are three places you can set baud rates...in the code (serial.begin(9600);), in the serial monitor, and then the upload setting from the menu. The upload setting won't affect the serial monitor.
@@ChilliChump2 and there it is staring at me right in the compiler/upload console output: "Changing baud rate to 921600". I am not seeing "9600" as an available baud rate for uploading.
You don't want to change the upload baud rate, like I said above that won't affect the serial monitor. Have a look at this image to see what you need to change: i.imgur.com/9s4RYTq.png
Things are going great, Have a few problems. How do I find the Baud rate of my computer? How do I find/or how do I change the com channel? Other than a few challenges we are doing great and hope to have it all done and in the greenhouse for my 87 birthday in September
Hi Carter, you don't need to know the baud rate of your computer. It is the the baud rate you set with the command: "Serial.begin(9600);". In that example, the baud rate is 9600. So on your Serial monitor, set the baud rate at the bottom to the same. And good luck with your automation project!!
Hi! Thanks so much for these videos! I've been programming for a while now but have never done anything with Micro controllers or IoT. I'm really excited! Definitely had to scrounge around for a DATA Micro usb cable... standard charging cables weren't working. Thanks again!
Thanks solved the issue in a second, everywhere else i could either find complex solutions or people saying board is damaged/fake etc. Thanks a lot
This did not work for me what to do
I have the problem it shows me: Failed uploading: uploading error: exit status 2 The power Led lights up normally as well as the temperature is warm but not hot. What can I do?
Thank you so much! Have wasted much time trying to upload first esp 32 and this fixed it!!!
Oh my god, You saved me with this 2 mins vid! Thank you so much!
i tried holding boot button but it didnt work
Bro exit status 2?
How to fix it
was a damaged board. My second board worked fine
I tried doing that too but it just seemed my buttons aint working.. the "connecting......." kept loading haha.
Any other ways to solve?
Getting the same error despite holding the button while uploading
yeaa, me too, have you solve it?
@@jundikhaalish2081 have u solved it bro ?
@@jundikhaalish2081 help me fix it if u found the solutions
@@KarkourYasser unfortunately no, i just bought new board:D
@@jundikhaalish2081 hhhhhhhhhhh thnx bro
Thank you very very much for this vídeo. As a matter of fact, I have the very same Output message as you do in the end, after solving you issue : "Resetting via RST pin". I've read in the documentation that this is not a bug, but rather a feature. In any case, if the program is really being loaded, I can not see the builtin Led blinking as it was supposed :(
Thank you very much Sir
HI
Thank you for your videos
I have an error when I start to build my sketch for esp32 but no issue for esp8266
I m using windows 10
This is the error : exec: "cmd": executable file not found in %path% compile error for esp32 dev module board
I need help
THANK YOU
I would check your path variable. In windows open up a command prompt. Then type "echo %path%". Check if there is anything weird going on there.
Gerrit Postema , NOT STARTING ? just place a condensator of 10uF between GND and EN !
What do you do if your ESP32 board does not have a boot button to fix this problem? I have the FireBeetle ESP32.
Not working
bro exit status 2;
how can i fix it.
please save me!!!!!!
Sir please do video on fatal error No serial data is received in esp32c3 many are facing the problem
did u get any solution .plz help
UsbEndpoint[mAddress=2,mAttributes=2,mMaxPacketSize=32,mInterval=0. Why problem 😢😢😢😢
hello mr. i have same problem like u,but i still dont know how to upload coding. I was do like you do, and last statement say it is "Leaving... Hard resetting via RTS pin... " .
When i get this statement, what should i do for can upload coding,please help me sir😢
Thanks bro, thats work
text size much better
I'm pulling my hair out on this one ! I constantly have th' 'No serial data recieved' error and can't upload. The only time that it works is when i completely remove the COM port device from my devices manager, reboot the computer and let it detect again. Then in the arduino software i can upload without any problem. It happens that it works twice but when it fails, i never get it to work again until i delete and add the comm port again. What a piece of garbage
Thanks pro
thank you
u r god
Have you experienced some unprintable characters being printed before the "Hello World" is printed? It is only printing the strange characters the first time "Hello World" is printed, all following prints look as expected. If I print with an empty string in the "Serial.println("");" I see only the strange characters. Thanks again.
FYI: I did also double check my baud rates were aligned at 9600.
I have only ever seen that when the baud rates are not the same. Just to confirm, are you setting the baud rate on the serial monitor itself to 9600 (bottom right of the serial monitor)? There are three places you can set baud rates...in the code (serial.begin(9600);), in the serial monitor, and then the upload setting from the menu. The upload setting won't affect the serial monitor.
@@ChilliChump2 and there it is staring at me right in the compiler/upload console output: "Changing baud rate to 921600".
I am not seeing "9600" as an available baud rate for uploading.
You don't want to change the upload baud rate, like I said above that won't affect the serial monitor. Have a look at this image to see what you need to change: i.imgur.com/9s4RYTq.png
Things are going great, Have a few problems. How do I find the Baud rate of my computer? How do I find/or how do I change the com channel? Other than a few challenges we are doing great and hope to have it all done and in the greenhouse for my 87 birthday in September
Hi Carter, you don't need to know the baud rate of your computer. It is the the baud rate you set with the command: "Serial.begin(9600);". In that example, the baud rate is 9600. So on your Serial monitor, set the baud rate at the bottom to the same. And good luck with your automation project!!
thank you ! Har har mahadev