Have as much fun as me and Robin did and sign up for a 14-day free trial and enjoy All of MyHeritage's amazing features. If you decide to continue your subscription, you’ll get a 50% discount. bit.ly/DaisyTempest2 ❤❤❤
There is nothing wrong with using linseed oil on oak. Th main reason not to, has to do with colour -as raw linseed oil makes oak very yellow (something you usually would avoid when working with oak) The drying time mentioned in other comments really is the same on oak as other similarly grained woods -absurdly long, as raw linseed oil takes up to months drying completely. Therefore you would normally use polymerized or “boiled” linseed oil. Where the polymerized oil is made by heating the oil in an oxygen free environment. Thereby starting the polymerising of the oil -thickening the oil and shortening the drying time. And Boiled linseed oil is made with adding metal salts as drying agents and solvents (typically turpentine) to decrease viscosity (boiled linseed oil, is also the most reactive of the two. So beware of drying rags. So think of raw linseed oil as a component in finishes such as paints and varnishes, not a “complete” finishing solution. Hope this helps. Best regards from a former cabinetmaker, now knife builder from Denmark
@@DaisyTempest metals in boiled linseed could react with tannins which is probably the reason for the "no oak" alao probably very unlikely to be an issue, have a hook in the bottom of a rake that's gone wonderfully black
Hi, 60 years ago I was an apprentice at Vauxhall motors as a pattern maker. I still have my toolbox full of the chisels and turning tools used for my job. Some of the tools I have I acquired from retiring workers. This making some of the tools up to 200 years old! Every so often I check that they are in good order. Also when I learnt my trade, everything was done by hand, no modern equipment. Enjoy, Dave r.
@@hughmac13 Hi, yes we did, first quality Honduras Mahogany, and Yellow Pine. All naturally seasoned, not kiln dried as now. For model making of new car 'bucks' we used a laminated timber called Stabelite. It was made from pulp timber from jungle swamps, and when seasoned and sealed, with varnish, was guaranteed not to move more than one thousandth of an inch. That's old measurements not metric!
@@Davidrollings-zr7bh That's right-you just do not want to be carving in kiln-dried woods if you have a care for your tool edges or the comfort of your hands and wrists. You were making the patterns for the engine castings? What are the "bucks"? Did the Stabelite carve well? I've wanted to learn about casting but haven't had a chance to get into it. I know there are cores and coreboxes and draft angles but that's it.
Hi, it's good you are interested in, what I call older trades. You are talking about two different types of pattern/model making. The first, using traditional timbers was indeed used to make patterns for engine blocks, gar box casings and axle casing. And if fact in many other parts of engineering. Most patterns were made to contraction size, not imperial measurement, as castings contract on cooling. Examples are 1/120, for aluminium, and 1/60 for cast iron. All pattern where build with a small taper to allow them to be removed from the sand in the foundry. Also there were cores to the patterns that could be removed to allow for holes, rebates etc. The second part, using Stabalite for new car bucks, basically was a complete model of a new car. When I was at vauxhall I worked on the HB Viva, Fc Victor, as well as Bedford commercial vehicles. In short when the model was complete, either plaster casts, or fibre glass mould were taken from the buck, and ultimately made into dies for the press shop, to make the panels. Stability was a very hard materiel and I remember alway sharpening any tools used. Final point, most patterns for the dies, were made from polystyrene! Hope this helps a bit? Dave r.
@@Davidrollings-zr7bh I've seen some good videos on TH-cam channels focused on casting or that feature casting as part of projects. I think it's interesting on its own, but as a cabinetmaker I had a wish to restore and build tools, which would necessitate casting in some cases. So my interest was in smaller pieces cast probably in bronze for the most part. I've seen foam used in some of those videos. I've also seen patterns that were 3D printed, which seems like an amazing way to create intricate shapes, and very rapidly. The part about patternmaking and casting that's so tricky to me is learning to see the negative of the object. It seems like something that takes practice because it doesn't come naturally to me at all.
For things like cleaning out that makers mark, I like to cut the end off a bamboo skewer with wire cutters or something that will compress and fray the cut end. It gives you a nice very stiff brush-like tool that you can use like a pencil eraser,. When it wears and softens, you can just cut it down a bit and keep going. Soft enough to keep from harming the piece you're working on, and hard enough to dig out even the most stubborn of buildup.
I love tools with a story, your great grandmothers chisel is a great example. I have just come into possession of a spirit level that belonged to my wife's great grandfather, I was gifted it by her grandma. Its a beautiful tool, I hope that I can do it as much justice as you have for this chisel
Love this video. I understand your hesitation. I'm a librarian and at one time considered becoming a conservator, but the job is literally "here's something priceless, a bottle of acid and a q-tip, get to work".
40+ years ago I inherited about a dozen lathe chisels from my great uncle; they're about the same age as your grandmother's. As I still don't have a lathe, they're simply sitting or rather hanging in my tool cabinet. It's comforting to know that I'll be passing these along to my son who will eventually get a lathe and restore them as you have done. Family heritage is a nice thing to have. Good job and have fun in Austin. I have a good friend who is also a great woodworker who lives there and I'd love to get the two of you together. She has a musical background, too. Travel well.
I have a few tools that were my father's, small pair of vise grips, hacksaw, and small ball pen hammer. He passed last year. That's great that you now have and are using it in your shop
Shellac is also a decent finishing solution for old tools. Feels good in the hand, easy to touch up, but does change the colour depending on the darkness of the shellac
I had always gotten someone else to sharpen my chisels, on the rare occasions I used one. Someone then gifted me a Richard Kell honing guide. It not only transformed my ability to be able to sharpen them as often as you are supposed to and therefore how often I could use them in the best condition, it also enabled me to re-profile and sharpen the others that I thought were in a condition beyond use.
Always a pleasure to watch one of your videos and note the care and attention you put into everything. I'm sure the oil on the chisel will be fine given the years it has had to dry out and close the grains .
Nice work. I have a number of old Sheffield chisels that I've restored pretty much the same way (except that I finish on waterstones), but having your great grandmother's is extra special.
So woodworking really runs in the family. So cool! It's a nice feeling to discover our ancestors had similar interests as we do. Kind of a bonding experience, though we can no longer meet the person.
That's the original handle (classic Marples shape) and it's made from Ash. As others have said, Linseed Oil is fine to use on Oak. Keep up the good work!👍🤩
I did this with my neighbour's old chisel a while ago - using the same faithful 400 grit stones - so i feel your pain... Lovely to restore a piece of family history like this. Great video!
I have used oils a lot over the years. Particularly BLO, Tung Oil and Walnut Oil. I have found that using solvents (citrus oil, pine oil) accelerates the adsorption of the ”cut” oils into denser woods. I have also used Japan Drier to speed up the process as well. A lot of tools that I have purchased have laquered handles so my first job when I get them in the shop is to strip that off and replace it with multiple coats of oil.
If I may be so brazen Daisy. When I was cleaning up a batch of chisels I used coarse wet dry sand paper to do the majority of the work. You can put them right on your existing stones and take of a lot of material quickly then go to your stones. Add water to the paper to help remove swarth.
Daisy that's a fine bit of family heritage kit you have there and now ready for service for another hundred years. Make sure your children know it's there and how important that tool is. Awesome job and thank you for sharing!
What a lovely video, I also have lots of Marples chisels that were my Grandfathers, I'm now in my 60s so they are very old, such good Sheffield steel, keep their edge for ages. I stopped putting a secondary bevel on a couple of years back with no apparent drawback that I have noticed, saves a lot of time! All my (many) chisels are now honed at 30dgrs. Travel safe and be lucky
I did enjoy your video. I wouldn’t be too concerned about the linseed oil. I enjoy your work and learning about guitar building. You also present yourself as personable and fun, good qualities.
2:30 You can get one of those cheep vibrating platforms and put that block on it. Then just hold the blade on top. Makes it like an inverted sander but, not.
Very nicely done. Just came across your channel and subbed. More info metalworking and machining myself but I do dabble a little in woodworking and always loved it. You did a great job sharpening and restoring that chisel. Looks really nice now.
Loved this. I recently found my Grandfather’s #5 jack plane. It was in dreadful condition. But after doing a restoration similar to yours, it is a beast!
Nice to see a Sheffield Marples chisel, as opposed to MiC. I still have a couple from my apprentice days (40+ yrs joiner), as well as some others I've picked up on the bay of various brands. I have a rosewood (I think) Marples mortice gauge that dates to the late 1800's with the original joiners initials stamped on.
I really enjoyed this episode. Thanks so much! I have restored many old hand tools over the years and they continue to inspire me whenever I use one of them. Kudos to you!
Great video, white vinegar makes a good rust cutter...when I'm restoring an old Stanley plane I'll pour some in a small plastic tub and soak the rusty parts for a day or two. Totally benign to work with, just make sure to rinse the steel well as the acid will promote rust as well as remove it;). Also, no need to flatten the entire back of the chisel, other than for aesthetic reasons. Even a half inch will do for good function, and sometimes the amount of cup or bow in an old blade will take FOREVER to flatten. Keep the videos coming!
I use tongue oil on oak all the time with no ill effects. Thinking linseed oil is similar. Nice clean up job. Love that you have a reverence for old tools
wonderful video! So many nice pieces of humanity in here: you doing very similar work as generations past, your cousin providing an advertisement we all watched through, and the care and dedication to maintaining craftsmanship - something so many have lost in our current society. Thank you.
Reinvigorating old tools is brilliant. Probably half of mine belonged to my grandfather. The ones I am responsible for are the higher tech ones, like the CNC I built. It started life barely able to cut MDF, and now it is fine with steel.
What a fun project! One tip I got for sharpening dulled chisels is that you don't have to flatten the WHOLE back - just the last inch or so that comes up to the tip - which can save a lot of time. Apologies if someone else already commented that - too many comments to sift through!
I've used linseed oil on my oak knife handles loads of times and it's never been a problem. Quite often needs a few extra applications as it seems to absorb a lot of it though.
NIce work as alwaysDaisy :) I have worked as a technician once or twice in school workshops. I had to sharpen all the chisels. Those water wheel grinding set ups like you have are great. The one I used also had a leather wheel to put compound on to polish the blades. I also had a stone next to it to debur the flat side of the blades. The chisels came out well, very sharp, though I was running out of hair on my left arm. I did my fathers old chisels while I was at it.
If only ""smell a vision"" would be a thing, woodworking shops always smell so nice. Much respect for your skills, I was trained to be a machinist so I understand how secure one must be. Woodworking is such a great skill to have, but creating musical instruments is IMHO next-level. I raked guitars in my lifetime and fiddled around trying to improve action, tone, etc. but when I did that( needed to adjust it for thinner strings) , I thought I killed that guitar. Eventually, after months of research and trial and error, I brought that guitar (an Epiphone LesPaul ""something-something"") back to life and it was so much better than when I started, but I promised myself I never ever try that again. What you do takes so much skill, knowledge, and expertise.
Great work! I love restoring hand-me-down tools by hand. The tool has more meaning when you use it later. A tip when you have a lot of sanding to do on chisels and the like is to not put excessive force on one side. It's really easy to take off more material from one side and never notice.
What a lovely heritage to have! I've never heard of BLO being a problem on oak, James Wright aka wood by wright uses it all the time on everything. I've just started using it and it gives a lovely feel. For an initial sharpening I believe axminster still offer a sharpening service or as you suggested a cheap honing guide with 240 grit sandpaper on either a piece of float glass, smooth granite table mat (as long as any reflection looks smooth) or even MDF or ply.
Boiled linseed oil is marvelous stuff. Thinned with turpentine, it is great for cleaning, refinishing, and rejuvenating wood. The rags can combust unless you soak them in water, but it's safe otherwise. It can make oak turn yellow (raw linseed oil is worse for this) but if you rub an old finish with fine steel wool and a 4:1 linseed turpentine mix, the old finish will re-emulsify.
Something I've been wanting to get is a nice chisel set as well as some quality whetstones and a strop. I rely on power tools a lot and have totally neglected my carving abilities, just finished my second bass though and I'm very happy with it.
a chisel made by your gt. grandmother... what a wonderful thing to have! All i have from my gt. grandmother is a washing dolly, which i use as a loo roll holder :)
I usually use a BLO/meths/turps mix a third of each one with 0000 steel wool for restoring old chisel handles, it cleans them without removing any patina or damaging them, that might have saved you some work with the dental tools.
You can use just wet-dry sandpaper at lower grit and work up to your diamond stone. Boiled linseed oil means it has metallic dryers in it to speed up drying. The metal can react with the oak tannins and darken it. Oak and chestnut just happen to have a lager amount of these acids. I suggest using a Pure tung oil. No dryers and will take about a week to fully dry but wont be tacky during that time.
Brilliant and respectful. Be careful of rags with linseed oil on them; they may spontaneously ignite. When linseed oil-soaked rags are left to dry, the oil oxidizes and generates heat. If this heat is trapped, as in a pile of rags, the temperature can rise enough to cause the rags to ignite on their own without any external flame.
@Daisy Tempest - My understanding is that using linseed oil on Oak is not suggested because it soaks way in and then it takes too long to dry which can allow mold to form on the uncured oil. Humidity and moisture would exacerbate the issue. Since the wood in question was already finished once, the new oil probably wasn't able to soak that far in. I would store that handle in a nice warm dry place. Boiled linseed dries faster. I've done 4-5 guitars and necks with the stuff, feels good and is pretty durable. Easy to fix/patch/repair too.
Daisy, thanks to your patience, your Great Grand Parents will be looking down and shining upon you after restoring that beautiful chisel, may it give you long and fruitful service, perfect!
Lovely stuff. Been a carpenter for over 30 years (mostly site work, but furniture too). I've restored a few things but definitely get impatient and definitely don't get anything like as fine a cutting edge as you do. Been wanting to get into sewing and recently restored a pair of old, battered Wilkinson dress making scissors, which was a love-hate process, but pleasing in the end. Don't doubt your identification of oak (and being porous I would have thought the boiled linseed oil would just soak in loads so you'd have to do a gazillion coats. Certainly not going to harm it.) but from my understanding, most traditional tool handles were made from ash. Also porous, but less so than oak. Mark in Scotland.
I ended up doing my own restoration of some u-gouges I bought from a vintage tool dealer. I learned a couple of things in the process. The grey coating is called a "patina" technically its oxidation, but its not the same color or as corrosive as rust. Rust is brown red, and usually a sign that the iron corroded severely. Patina is light to dark grey, it's extremely mild and won't damage your tools compared to rust. Patina is very common in old tools due to the high carbon content. It's not harmful, and in the long run, it's not worth it to remove all of the patina from the entire tool since it will just turn dark grey again after a number of years. Simply wiping tools down after use, and some light motor oil should be enough to maintain them long term.
This is a guess about oak and linseed oil, but maybe the concern is that oil which soaks deeply into the pores will never cure since it's cut off from oxygen, and so maybe the piece would continually seep with uncured oil afterwards? But since that piece has been previously finished, I think you're right that the pores are likely to be well sealed already. Any linseed on the surface should cure just fine.
Yes a lot of people have said ash. I think you might be right. I’m also wondering if this is the handle she turned herself or if I picked the wrong one out the drawer of them. Which would be a shame as it negates the whole point of the video 😂 shame she’s not around to ask which ones she turned new handles for.
@@DaisyTempest It's a stock standard Marples ash handle and they had quite a number of different patterns. My favourite is the "London Pattern" octagonal ones. I will often replace my handles with ones made from rosewood (all types)" or ebony. Linseed oil is fine, but yeah, be careful of spontaneous combustion with any used oil or shellac rags. Your dating of the chisel is not too bad - anything from around 1900 to the mid/late 1940's. After that they tended to have round shanks.
This popped up in recommended today and sent me on a spiral down through hours so far of your videos. I am also a woodworker and had a love for the small things, I think I have lost that working in a joinery shop where we pump out white boxes. Detailed white boxes, but white boxes nonetheless. I was wondering in terms of luthiers, how much of a musical background do you think luthiers need? Very much love the content and was a very fast subscriber!
Wouldn't have thought to touch the precious handle that your relatives had held on to. Sharpening the blade absolutely! Using it? 1,000,000%!! But not my channel nor my chisel. I honestly watch most of your videos in the early morning because you're so chill. You bring me peace into an already very peaceful life. Thank you.
For the delicate carvings on the wood, I've found a stiff, nylon bristle brush to be effective and safe. Also, it looks like your diamond stones haven't been cleaned in a while, which will diminish their cutting power. Dishwashing liquid, hot water, and a stiff toothbrush or non-abrasive scotch-brite pad or a sponge with a scouring pad backing.
Where should I begin… Really great video as always. I actually dared to try to make a small chisel (about 4 mm in width) once. And after seeing this video I got curious of trying to restore a pocket knife that I found in my family’s old woodshed. - Yes, family is important! I’m familiar with your sponsor and they really are great. I’ve found that I have sailors and explorers in my family tree, on my mother’s side. Robin is amazing! I remember seeing a young kid on your channel before. Was that him? Time flies… Oh, and the music about.. was it 5 minutes in? I think so. I’m in the sofa and thinking I want to play something, and now I got it: Blues! Thanks 😊 And thanks for being here. You’re amazing! 👍
09:15 - 09:38 : After listening to that section, I'd definitely love to see you do woodwork ASMR videos with this chisel. Who's with me 😅? Anyway, great job, Daisy!
White oak is not porous, that’s why it works so well for whiskey and wine barrels. I believe English and French oak are white oaks. Love your video from here in Cincinnati!
I use linseed oil on oak all the time, just need to leave time for the coats to dry and then wipe off excess - although on my tiny phone screen the handle looked like ash.
Great video and the finished tool looks lovely. There is no reason you cannot use boiled linseed oil on oak. I’ve used it on picture frames and the like for years, followed by a final coat of wax. No issues whatsoever. I love traditional finishes as they are inexpensive, easy to apply and avoid the dipped in plastic look.
The red/black oaks are very open pored, which is why you don't see any wine or whiskey barrels made from it. Split a billet of red oak and stick it in a bucket of water, and you can blow bubbles out the end. You can't do this with white oak. Biggest problem I can see with the open pores of some woods would be bleed out where you get little puddles/spots of oil that bleed out as the oil cures. You can use an air hose to blow out the pores before the oil cures, or you can wait till it dries and hit it with steel wool. As for dental picks, next time you see your dentist, ask them. They do have drawers full of them that they don't/won't/can't use any more.
Have as much fun as me and Robin did and sign up for a 14-day free trial and enjoy All of MyHeritage's amazing features. If you decide to continue your subscription, you’ll get a 50% discount. bit.ly/DaisyTempest2 ❤❤❤
51 and 🐵
There is nothing wrong with using linseed oil on oak. Th main reason not to, has to do with colour -as raw linseed oil makes oak very yellow (something you usually would avoid when working with oak) The drying time mentioned in other comments really is the same on oak as other similarly grained woods -absurdly long, as raw linseed oil takes up to months drying completely. Therefore you would normally use polymerized or “boiled” linseed oil. Where the polymerized oil is made by heating the oil in an oxygen free environment. Thereby starting the polymerising of the oil -thickening the oil and shortening the drying time. And Boiled linseed oil is made with adding metal salts as drying agents and solvents (typically turpentine) to decrease viscosity (boiled linseed oil, is also the most reactive of the two. So beware of drying rags. So think of raw linseed oil as a component in finishes such as paints and varnishes, not a “complete” finishing solution.
Hope this helps. Best regards from a former cabinetmaker, now knife builder from Denmark
That explains why an old file that I inherited from my father has that very yellow finish.
Thank you so much for the intel! Glad you helped not just me but everyone else who came here. Thank you :)
I’m glad to be of any help. Keep up the great content!
Only use raw linseed oil on traditional old willow cricket bats!
@@DaisyTempest metals in boiled linseed could react with tannins which is probably the reason for the "no oak" alao probably very unlikely to be an issue, have a hook in the bottom of a rake that's gone wonderfully black
Hi, 60 years ago I was an apprentice at Vauxhall motors as a pattern maker. I still have my toolbox full of the chisels and turning tools used for my job. Some of the tools I have I acquired from retiring workers. This making some of the tools up to 200 years old! Every so often I check that they are in good order. Also when I learnt my trade, everything was done by hand, no modern equipment.
Enjoy, Dave r.
You must have had access to some great-quality mahogany in those days.
@@hughmac13 Hi, yes we did, first quality Honduras Mahogany, and Yellow Pine. All naturally seasoned, not kiln dried as now. For model making of new car 'bucks' we used a laminated timber called Stabelite. It was made from pulp timber from jungle swamps, and when seasoned and sealed, with varnish, was guaranteed not to move more than one thousandth of an inch. That's old measurements not metric!
@@Davidrollings-zr7bh That's right-you just do not want to be carving in kiln-dried woods if you have a care for your tool edges or the comfort of your hands and wrists.
You were making the patterns for the engine castings? What are the "bucks"? Did the Stabelite carve well? I've wanted to learn about casting but haven't had a chance to get into it. I know there are cores and coreboxes and draft angles but that's it.
Hi, it's good you are interested in, what I call older trades.
You are talking about two different types of pattern/model making. The first, using traditional timbers was indeed used to make patterns for engine blocks, gar box casings and axle casing. And if fact in many other parts of engineering. Most patterns were made to contraction size, not imperial measurement, as castings contract on cooling. Examples are 1/120, for aluminium, and 1/60 for cast iron. All pattern where build with a small taper to allow them to be removed from the sand in the foundry. Also there were cores to the patterns that could be removed to allow for holes, rebates etc.
The second part, using Stabalite for new car bucks, basically was a complete model of a new car. When I was at vauxhall I worked on the HB Viva, Fc Victor, as well as Bedford commercial vehicles. In short when the model was complete, either plaster casts, or fibre glass mould were taken from the buck, and ultimately made into dies for the press shop, to make the panels.
Stability was a very hard materiel and I remember alway sharpening any tools used.
Final point, most patterns for the dies, were made from polystyrene!
Hope this helps a bit?
Dave r.
@@Davidrollings-zr7bh I've seen some good videos on TH-cam channels focused on casting or that feature casting as part of projects.
I think it's interesting on its own, but as a cabinetmaker I had a wish to restore and build tools, which would necessitate casting in some cases. So my interest was in smaller pieces cast probably in bronze for the most part.
I've seen foam used in some of those videos. I've also seen patterns that were 3D printed, which seems like an amazing way to create intricate shapes, and very rapidly. The part about patternmaking and casting that's so tricky to me is learning to see the negative of the object. It seems like something that takes practice because it doesn't come naturally to me at all.
For things like cleaning out that makers mark, I like to cut the end off a bamboo skewer with wire cutters or something that will compress and fray the cut end. It gives you a nice very stiff brush-like tool that you can use like a pencil eraser,. When it wears and softens, you can just cut it down a bit and keep going. Soft enough to keep from harming the piece you're working on, and hard enough to dig out even the most stubborn of buildup.
Great tip! Thanks!
That is a great tip.
I love tools with a story, your great grandmothers chisel is a great example. I have just come into possession of a spirit level that belonged to my wife's great grandfather, I was gifted it by her grandma. Its a beautiful tool, I hope that I can do it as much justice as you have for this chisel
Love this video. I understand your hesitation. I'm a librarian and at one time considered becoming a conservator, but the job is literally "here's something priceless, a bottle of acid and a q-tip, get to work".
40+ years ago I inherited about a dozen lathe chisels from my great uncle; they're about the same age as your grandmother's. As I still don't have a lathe, they're simply sitting or rather hanging in my tool cabinet. It's comforting to know that I'll be passing these along to my son who will eventually get a lathe and restore them as you have done. Family heritage is a nice thing to have. Good job and have fun in Austin. I have a good friend who is also a great woodworker who lives there and I'd love to get the two of you together. She has a musical background, too. Travel well.
This is lovely! Thank you for the comment. Good luck to your son for the restoration :)
Buy him a mini lathe, Grant!
Great video Daisy. These little side "excursions" are enjoyable to watch.
Thank you
I have a few tools that were my father's, small pair of vise grips, hacksaw, and small ball pen hammer. He passed last year.
That's great that you now have and are using it in your shop
Shellac is also a decent finishing solution for old tools. Feels good in the hand, easy to touch up, but does change the colour depending on the darkness of the shellac
Chisels haven't changed much, and an old chisel is still useful today. It looks very much like mine.
What a credit you are to your grandparents and what a great way to honour them. Really informative too.
damn, I did not expect this video to be so wholesome. then again, might be just the sympathetic person presenting it ☺
I had always gotten someone else to sharpen my chisels, on the rare occasions I used one. Someone then gifted me a Richard Kell honing guide. It not only transformed my ability to be able to sharpen them as often as you are supposed to and therefore how often I could use them in the best condition, it also enabled me to re-profile and sharpen the others that I thought were in a condition beyond use.
You're so fortunate to have a family heirloom to use and restore!
Always a pleasure to watch one of your videos and note the care and attention you put into everything. I'm sure the oil on the chisel will be fine given the years it has had to dry out and close the grains .
Nice to see Lindsey Doyle doing the rounds, very enjoyable video, beautifully restored.
Not me nearly doing your accent every time I think about Lindsay Doyle
Glad to see you carrying on the family legacy! Love the history behind the tool too.
Nicely done Daisy! Restoring a treasured hand me down is always a good thing! 👍👍💖💖
Nice work. I have a number of old Sheffield chisels that I've restored pretty much the same way (except that I finish on waterstones), but having your great grandmother's is extra special.
So woodworking really runs in the family. So cool! It's a nice feeling to discover our ancestors had similar interests as we do. Kind of a bonding experience, though we can no longer meet the person.
😮😮 Love the final result. That chisel will work perfectly shaping wood other 100 years.
I love your beautiful accent too.
Love it. Using the tools of our ancestors or restoring them is the best way to honor them.
heirloom tools have so much charm
Hi Daisy, Rustins danish oil is brill... great for oak kitchen worktops or even sealing guitars against moisture. All the best...x
That's the original handle (classic Marples shape) and it's made from Ash. As others have said, Linseed Oil is fine to use on Oak. Keep up the good work!👍🤩
Glad you said it. i was getting a bit touretty watching the vid.
This is really inspiring, I love knowing other people care for old tools.
I've used linseed oil on oak before it just takes a few coats to get the look you want.
I did this with my neighbour's old chisel a while ago - using the same faithful 400 grit stones - so i feel your pain...
Lovely to restore a piece of family history like this. Great video!
I have used oils a lot over the years. Particularly BLO, Tung Oil and Walnut Oil. I have found that using solvents (citrus oil, pine oil) accelerates the adsorption of the ”cut” oils into denser woods. I have also used Japan Drier to speed up the process as well. A lot of tools that I have purchased have laquered handles so my first job when I get them in the shop is to strip that off and replace it with multiple coats of oil.
If I may be so brazen Daisy. When I was cleaning up a batch of chisels I used coarse wet dry sand paper to do the majority of the work. You can put them right on your existing stones and take of a lot of material quickly then go to your stones. Add water to the paper to help remove swarth.
What a wholesome find this channel was...
I use Linseed oil on all my children's and grand children's oak furniture. You're perfectly fine. Love your channel.
Daisy that's a fine bit of family heritage kit you have there and now ready for service for another hundred years. Make sure your children know it's there and how important that tool is. Awesome job and thank you for sharing!
What a lovely video, I also have lots of Marples chisels that were my Grandfathers, I'm now in my 60s so they are very old, such good Sheffield steel, keep their edge for ages. I stopped putting a secondary bevel on a couple of years back with no apparent drawback that I have noticed, saves a lot of time! All my (many) chisels are now honed at 30dgrs. Travel safe and be lucky
I did enjoy your video. I wouldn’t be too concerned about the linseed oil. I enjoy your work and learning about guitar building. You also present yourself as personable and fun, good qualities.
Thanks for the kind comment!
2:30 You can get one of those cheep vibrating platforms and put that block on it. Then just hold the blade on top. Makes it like an inverted sander but, not.
Fun project. I'm sure your great grandmother would love to know that someone in the family was still using her tools!
Very nicely done. Just came across your channel and subbed.
More info metalworking and machining myself but I do dabble a little in woodworking and always loved it.
You did a great job sharpening and restoring that chisel. Looks really nice now.
I love your channel! It is so fun and interesting to watch. And, your cousin Robin is adorable!
Dentists tools are great. You often can get used dentist tools quite cheaply for the Dremel as well.
Loved this. I recently found my Grandfather’s #5 jack plane. It was in dreadful condition. But after doing a restoration similar to yours, it is a beast!
Nice to see a Sheffield Marples chisel, as opposed to MiC. I still have a couple from my apprentice days (40+ yrs joiner), as well as some others I've picked up on the bay of various brands. I have a rosewood (I think) Marples mortice gauge that dates to the late 1800's with the original joiners initials stamped on.
I really enjoyed this episode. Thanks so much!
I have restored many old hand tools over the years and they continue to inspire me whenever I use one of them.
Kudos to you!
Great video, white vinegar makes a good rust cutter...when I'm restoring an old Stanley plane I'll pour some in a small plastic tub and soak the rusty parts for a day or two. Totally benign to work with, just make sure to rinse the steel well as the acid will promote rust as well as remove it;). Also, no need to flatten the entire back of the chisel, other than for aesthetic reasons. Even a half inch will do for good function, and sometimes the amount of cup or bow in an old blade will take FOREVER to flatten. Keep the videos coming!
I use tongue oil on oak all the time with no ill effects. Thinking linseed oil is similar. Nice clean up job. Love that you have a reverence for old tools
wonderful video! So many nice pieces of humanity in here: you doing very similar work as generations past, your cousin providing an advertisement we all watched through, and the care and dedication to maintaining craftsmanship - something so many have lost in our current society. Thank you.
I have my Dad's handplane and I feel the same way about it as you do about the chisel. Wonderful video.
Reinvigorating old tools is brilliant. Probably half of mine belonged to my grandfather. The ones I am responsible for are the higher tech ones, like the CNC I built. It started life barely able to cut MDF, and now it is fine with steel.
What a fun project! One tip I got for sharpening dulled chisels is that you don't have to flatten the WHOLE back - just the last inch or so that comes up to the tip - which can save a lot of time. Apologies if someone else already commented that - too many comments to sift through!
A fantastic tutorial on refurbishing a wonderful tool
9:16
Phenomenal control.
Awesome chip.
Haha thank you! Very satisfying indeed.
I've used linseed oil on my oak knife handles loads of times and it's never been a problem. Quite often needs a few extra applications as it seems to absorb a lot of it though.
NIce work as alwaysDaisy :) I have worked as a technician once or twice in school workshops. I had to sharpen all the chisels. Those water wheel grinding set ups like you have are great. The one I used also had a leather wheel to put compound on to polish the blades. I also had a stone next to it to debur the flat side of the blades. The chisels came out well, very sharp, though I was running out of hair on my left arm. I did my fathers old chisels while I was at it.
Haha! I hope your hair grew back. I have barely any either :( such a pain!
nice job ! I need to fix up some real soon.. I stored them improper and they need attention. Nice job and vid :-)
You did a great job on the chisel. I love restoring old hand tools. I find it very rewarding. Keep up the good work. Love your videos.
Very nicely done Dasiy, loved your test passes, truly steady hands. 😍
Glad you enjoyed it!
Fascinating. Beautiful restoration of a great heirloom.
If only ""smell a vision"" would be a thing, woodworking shops always smell so nice. Much respect for your skills, I was trained to be a machinist so I understand how secure one must be. Woodworking is such a great skill to have, but creating musical instruments is IMHO next-level. I raked guitars in my lifetime and fiddled around trying to improve action, tone, etc. but when I did that( needed to adjust it for thinner strings) , I thought I killed that guitar. Eventually, after months of research and trial and error, I brought that guitar (an Epiphone LesPaul ""something-something"") back to life and it was so much better than when I started, but I promised myself I never ever try that again.
What you do takes so much skill, knowledge, and expertise.
Amazing work on the fine details of the maker's mark, and name carving in the handle!
I love that you plan to use the chisel in the workshop 👍
Great work! I love restoring hand-me-down tools by hand. The tool has more meaning when you use it later.
A tip when you have a lot of sanding to do on chisels and the like is to not put excessive force on one side. It's really easy to take off more material from one side and never notice.
Great video! Love the story behind the tools and keeping your heritage alive.
What a lovely heritage to have! I've never heard of BLO being a problem on oak, James Wright aka wood by wright uses it all the time on everything. I've just started using it and it gives a lovely feel. For an initial sharpening I believe axminster still offer a sharpening service or as you suggested a cheap honing guide with 240 grit sandpaper on either a piece of float glass, smooth granite table mat (as long as any reflection looks smooth) or even MDF or ply.
Boiled linseed oil is marvelous stuff. Thinned with turpentine, it is great for cleaning, refinishing, and rejuvenating wood. The rags can combust unless you soak them in water, but it's safe otherwise. It can make oak turn yellow (raw linseed oil is worse for this) but if you rub an old finish with fine steel wool and a 4:1 linseed turpentine mix, the old finish will re-emulsify.
Something I've been wanting to get is a nice chisel set as well as some quality whetstones and a strop. I rely on power tools a lot and have totally neglected my carving abilities, just finished my second bass though and I'm very happy with it.
a chisel made by your gt. grandmother... what a wonderful thing to have! All i have from my gt. grandmother is a washing dolly, which i use as a loo roll holder :)
Hola Daisy!! Sin duda Robin tiene un gran futuro. Quedo como nuevo el cincel, gran trabajó. Saludos desde Argentina.
I usually use a BLO/meths/turps mix a third of each one with 0000 steel wool for restoring old chisel handles, it cleans them without removing any patina or damaging them, that might have saved you some work with the dental tools.
You can use just wet-dry sandpaper at lower grit and work up to your diamond stone. Boiled linseed oil means it has metallic dryers in it to speed up drying. The metal can react with the oak tannins and darken it. Oak and chestnut just happen to have a lager amount of these acids. I suggest using a Pure tung oil. No dryers and will take about a week to fully dry but wont be tacky during that time.
Brilliant and respectful. Be careful of rags with linseed oil on them; they may spontaneously ignite. When linseed oil-soaked rags are left to dry, the oil oxidizes and generates heat. If this heat is trapped, as in a pile of rags, the temperature can rise enough to cause the rags to ignite on their own without any external flame.
@Daisy Tempest - My understanding is that using linseed oil on Oak is not suggested because it soaks way in and then it takes too long to dry which can allow mold to form on the uncured oil. Humidity and moisture would exacerbate the issue. Since the wood in question was already finished once, the new oil probably wasn't able to soak that far in. I would store that handle in a nice warm dry place. Boiled linseed dries faster. I've done 4-5 guitars and necks with the stuff, feels good and is pretty durable. Easy to fix/patch/repair too.
Daisy, thanks to your patience, your Great Grand Parents will be looking down and shining upon you after restoring that beautiful chisel, may it give you long and fruitful service, perfect!
Nicely done! With a little love and periodic maintenance, it should easily last another hundred years.
Lovely stuff. Been a carpenter for over 30 years (mostly site work, but furniture too). I've restored a few things but definitely get impatient and definitely don't get anything like as fine a cutting edge as you do. Been wanting to get into sewing and recently restored a pair of old, battered Wilkinson dress making scissors, which was a love-hate process, but pleasing in the end.
Don't doubt your identification of oak (and being porous I would have thought the boiled linseed oil would just soak in loads so you'd have to do a gazillion coats. Certainly not going to harm it.) but from my understanding, most traditional tool handles were made from ash. Also porous, but less so than oak.
Mark in Scotland.
Yes I think you're right Mark, ash or beech would be my thought, though ash can look like oak in the right light
I ended up doing my own restoration of some u-gouges I bought from a vintage tool dealer. I learned a couple of things in the process. The grey coating is called a "patina" technically its oxidation, but its not the same color or as corrosive as rust. Rust is brown red, and usually a sign that the iron corroded severely. Patina is light to dark grey, it's extremely mild and won't damage your tools compared to rust.
Patina is very common in old tools due to the high carbon content. It's not harmful, and in the long run, it's not worth it to remove all of the patina from the entire tool since it will just turn dark grey again after a number of years. Simply wiping tools down after use, and some light motor oil should be enough to maintain them long term.
You look so much like you great grandmother, great vid and love the chisel :-)
This is a guess about oak and linseed oil, but maybe the concern is that oil which soaks deeply into the pores will never cure since it's cut off from oxygen, and so maybe the piece would continually seep with uncured oil afterwards? But since that piece has been previously finished, I think you're right that the pores are likely to be well sealed already. Any linseed on the surface should cure just fine.
I think the handle is made of ash wood. William Marples and Sons, Ltd. used to put an ash or beech handle.
Yes a lot of people have said ash. I think you might be right. I’m also wondering if this is the handle she turned herself or if I picked the wrong one out the drawer of them. Which would be a shame as it negates the whole point of the video 😂 shame she’s not around to ask which ones she turned new handles for.
@@DaisyTempest google it Wiliam Marples tools catalog and You will fiind which handle is
@@DaisyTempest It's a stock standard Marples ash handle and they had quite a number of different patterns. My favourite is the "London Pattern" octagonal ones. I will often replace my handles with ones made from rosewood (all types)" or ebony. Linseed oil is fine, but yeah, be careful of spontaneous combustion with any used oil or shellac rags. Your dating of the chisel is not too bad - anything from around 1900 to the mid/late 1940's. After that they tended to have round shanks.
Really enjoyed this! Keep em coming Daisy 🙂
Thank you!
Everything you do is interesting and entertaining.
Thanks so kind. Thank you!
This popped up in recommended today and sent me on a spiral down through hours so far of your videos. I am also a woodworker and had a love for the small things, I think I have lost that working in a joinery shop where we pump out white boxes. Detailed white boxes, but white boxes nonetheless. I was wondering in terms of luthiers, how much of a musical background do you think luthiers need?
Very much love the content and was a very fast subscriber!
Great job Daisy. James Wright always uses boiled linseed oil on oak, so i think it's not a problem.
Nice Restoration Daisy - thanks for the video, safe trip stateside - Cheers from Canada
Wouldn't have thought to touch the precious handle that your relatives had held on to. Sharpening the blade absolutely! Using it? 1,000,000%!! But not my channel nor my chisel. I honestly watch most of your videos in the early morning because you're so chill. You bring me peace into an already very peaceful life. Thank you.
If you ever need to clean up, repair, or even create, finely carved details again, look into gunstock carving tools. In particular, checkering tools
Being good with wood runs in the family? Fascinating ❤
For the delicate carvings on the wood, I've found a stiff, nylon bristle brush to be effective and safe. Also, it looks like your diamond stones haven't been cleaned in a while, which will diminish their cutting power. Dishwashing liquid, hot water, and a stiff toothbrush or non-abrasive scotch-brite pad or a sponge with a scouring pad backing.
Where should I begin…
Really great video as always.
I actually dared to try to make a small chisel (about 4 mm in width) once. And after seeing this video I got curious of trying to restore a pocket knife that I found in my family’s old woodshed. - Yes, family is important!
I’m familiar with your sponsor and they really are great. I’ve found that I have sailors and explorers in my family tree, on my mother’s side.
Robin is amazing! I remember seeing a young kid on your channel before. Was that him? Time flies…
Oh, and the music about.. was it 5 minutes in? I think so. I’m in the sofa and thinking I want to play something, and now I got it: Blues! Thanks 😊
And thanks for being here. You’re amazing! 👍
Thanks so much for your lovely comment. I’ll tell Robin he did a great job!
Your words are so poetic. Great video!
09:15 - 09:38 : After listening to that section, I'd definitely love to see you do woodwork ASMR videos with this chisel. Who's with me 😅?
Anyway, great job, Daisy!
You’re amazing! I love old tools and restoring old treasures, bonus you’re a pretty girl with an English accent. Couldn’t make a more perfect video! ❤
It'll be fine. Nice work!
White oak is not porous, that’s why it works so well for whiskey and wine barrels. I believe English and French oak are white oaks.
Love your video from here in Cincinnati!
That's neat that she was a wood worker too. She would be proud of you. Fo Shizzle 😊
Really beautiful work, Daisy! 😊
And don't worry, woodworkers all around the world use BLO on oak.
Anyway, stay safe there with your family! 🖖😊
You did a great job. It was fun and inspiring to watch. And thanks for the scammer warning, I have been pestered with those on other channels.
I use linseed oil on oak all the time, just need to leave time for the coats to dry and then wipe off excess - although on my tiny phone screen the handle looked like ash.
Great video and the finished tool looks lovely. There is no reason you cannot use boiled linseed oil on oak. I’ve used it on picture frames and the like for years, followed by a final coat of wax. No issues whatsoever. I love traditional finishes as they are inexpensive, easy to apply and avoid the dipped in plastic look.
Worth all the work 👍
The red/black oaks are very open pored, which is why you don't see any wine or whiskey barrels made from it. Split a billet of red oak and stick it in a bucket of water, and you can blow bubbles out the end. You can't do this with white oak. Biggest problem I can see with the open pores of some woods would be bleed out where you get little puddles/spots of oil that bleed out as the oil cures. You can use an air hose to blow out the pores before the oil cures, or you can wait till it dries and hit it with steel wool.
As for dental picks, next time you see your dentist, ask them. They do have drawers full of them that they don't/won't/can't use any more.