You can build a water level much cheaper. All you need is the same clear tubing, but you can use an empty plastic milk jug for your "base station." Just loop it through the handle a couple times before putting it down into the jug so it won't come out. The hole does not have to be in the bottom of the container. It will work just as well bringing it up and out the top of the jug, and you don't have to use a fitting that may or may not leak. Just set your jug on a kitchen chair, or the paint can shelf of your ladder. . . . you don't need to build a fancy contraption unless you want to. Remember, you will have to store it when your pool leveling needs are finished. You have a kink in the bottom of your story pole? Don't drill a hole for your tubing. Just put the lowest attachment point about 6" up from the bottom and leave the tubing free from there....it will not kink. If you put a wooden disk onto the bottom of your story pole, you can probably get it to stand un-aided.
I've been surfing TH-cam , trying to find an easy one-man way to measure for leveling my pool. There is nothing like this anywhere. This makes so much sense and you've helped me immensely. Thank you very much for the video. .
Thank you for being so detailed. I probably watched 15 videos before I finally found someone who would show me exactly how the water level works. I have a 60 foot span I am building a retaining wall and for the life of me cannot figure out how I was going to do this. My son suggested I use a water level I have no clue really how they worked but your video detailed it extremely well.
@@garrettscott9427 I guess the only thing I did wrong was use a 1/4 in tube. I think 1/2 would be better. The liquid move so slow and it’s really affected by the temperature
The best easiest perfect way!! I have planned to do this for my 16x32 Bestway (Intex). This will insure all 24 support bricks (or blocks) have the exact same PLANE. The poles are all the exact same length. If done this way the top edge of the pool will be PERFECT. Same pole length plus same pad horizon for all pads equals success. The rectangular edge on all four sides depend on this to be perfect. relatively speaking it is not as important for the bottom of the pool to be exact , just smooth and close. It is the outer edge that matters. Of course if you have a basketball under the center then the material will be shorter side to side in that area causing those supports to stand more upright. Good job Garret, this is the most under and never talked about technique for making a pool level. Your is the only one. I did this search because my brother asked me to do a video for my pool. FLAT is not the same as level. Water does not lie. :)
Ideas: Have a patio tile near the base station that does not move outside the pool area for 'calibration'. Good tip about temperature expansion. Be sure you get the soft vinyl tubing with a large diameter like yours; our local ACE has vinyl, but it is very stiff (so get the cheaper stuff). I am using a longer 1x2 and have my base station higher so I can read at chest level. Also, my 18'x4' AGP has 13 legs, so I started by digging recesses for (13) 12" round pavers that are 1.8125" thick, and calculating in SolidWorks the distance between centers, and scribed a line 18' diameter in the dirt.
You are the only person I have seen with a hilly yard like mine. We have had a pool for 2 years and it is always not leveled. I will use your techniques to level my yard this year. Thank you so much for this video!!!
Hey Garrett im wanting to use the water level to level a pier an beam cabin an was wanting to measure from the bottom of the floor joists underneath the house at each pad supporting the joists. I can see how it works on the ground elevations but i would be bringing my stick up to the bottom of the floor joists an trying to read the difference. Question is will it work backwards by using the top of the stick instead of the bottom ?
I’m getting ready to level our spot for the pool now. Thanks for this video! Later this year we’ll be doing a 10x8 shed and yours looks great! How’d did you do yours?
You are welcome! I used concrete deck blocks for the foundation of the shed. Here is an unlisted video that covers the process somewhat. th-cam.com/video/wJCJGDj_N2Y/w-d-xo.html
Materials used to build the water level: Bucket: www.lowes.com/pd/United-Solutions-2-Gallon-Residential-Bucket/1000462837 Lid: www.lowes.com/pd/Letica-9-6-in-White-Plastic-Bucket-Lid/50434790 Tubing 35ft: www.lowes.com/pd/B-K-1-2-in-x-1-ft-PVC-Clear-Vinyl-Tubing/1000115993 Fitting: www.lowes.com/pd/B-K-3-8-in-Barbed-Barb-x-MIP-Elbow-Fitting/1000505073 2x4: www.lowes.com/pd/Top-Choice-2-x-4-x-8-ft-Whitewood-Stud-Common-1-5-in-x-3-5-in-x-8-ft-Actual/1000051161 Black Food Coloring: Amazon Affiliate Link: amzn.to/2VgwdbL or www.walmart.com/ip/McCormick-Black-Food-Color-1-fl-oz/10309022?selected=true Gardner Bender Plastic Cable Staples - Around 1/2" : No link Drill Bit: www.harborfreight.com/3-piece-titanium-nitride-coated-high-speed-steel-step-drills-91616.html
I disabled an I’m trying to fix this old moble home it’s a small single wide no blocks under it yet I want to do it myself can’t pay anybody to go it could you tell me how I would use this method an where would my starting point be on the moble home I really need to understand this method if you can help please thank you
I have an Intex 18'x52" round, and I am on my third attempt at leveling the pool. This time, I am going to use a water level, and I like your video the best. I will be putting my level together today, using your video as a guide. Thanks for a great video...and wish me luck! :)
I hate the wind, 2 times i had to start completely over. I hate this design of this pool, and the harware is on the cheap side. That must be the difference between a 2000 dollar pool and a 7000 dollar pool.
![[TH] 2024 PMWC x EWC Group Stage Day 3 | PUBG MOBILE WORLD CUP x ESPORTS WORLD CUP](http://i.ytimg.com/vi/VnOqutfqWqU/mqdefault.jpg)
You can build a water level much cheaper. All you need is the same clear tubing, but you can use an empty plastic milk jug for your "base station." Just loop it through the handle a couple times before putting it down into the jug so it won't come out. The hole does not have to be in the bottom of the container. It will work just as well bringing it up and out the top of the jug, and you don't have to use a fitting that may or may not leak. Just set your jug on a kitchen chair, or the paint can shelf of your ladder. . . . you don't need to build a fancy contraption unless you want to. Remember, you will have to store it when your pool leveling needs are finished.
You have a kink in the bottom of your story pole? Don't drill a hole for your tubing. Just put the lowest attachment point about 6" up from the bottom and leave the tubing free from there....it will not kink. If you put a wooden disk onto the bottom of your story pole, you can probably get it to stand un-aided.
I've been surfing TH-cam , trying to find an easy one-man way to measure for leveling my pool. There is nothing like this anywhere. This makes so much sense and you've helped me immensely. Thank you very much for the video. .
you are welcome!
Thank you for being so detailed. I probably watched 15 videos before I finally found someone who would show me exactly how the water level works. I have a 60 foot span I am building a retaining wall and for the life of me cannot figure out how I was going to do this. My son suggested I use a water level I have no clue really how they worked but your video detailed it extremely well.
thanks for the feedback! I actually just made a 100ft version of this 2 weeks ago that I used to map out the topography of a poorly graded backyard.
@@garrettscott9427 I guess the only thing I did wrong was use a 1/4 in tube. I think 1/2 would be better. The liquid move so slow and it’s really affected by the temperature
@@annastanfield5473 are you letting the end of the tube vent?
The best easiest perfect way!! I have planned to do this for my 16x32 Bestway (Intex). This will insure all 24 support bricks (or blocks) have the exact same PLANE. The poles are all the exact same length. If done this way the top edge of the pool will be PERFECT. Same pole length plus same pad horizon for all pads equals success. The rectangular edge on all four sides depend on this to be perfect. relatively speaking it is not as important for the bottom of the pool to be exact , just smooth and close. It is the outer edge that matters. Of course if you have a basketball under the center then the material will be shorter side to side in that area causing those supports to stand more upright. Good job Garret, this is the most under and never talked about technique for making a pool level. Your is the only one. I did this search because my brother asked me to do a video for my pool. FLAT is not the same as level. Water does not lie. :)
thank for the feedback!
Ingenious, really awesome man! Thanks
you are welcome!
Ideas: Have a patio tile near the base station that does not move outside the pool area for 'calibration'. Good tip about temperature expansion. Be sure you get the soft vinyl tubing with a large diameter like yours; our local ACE has vinyl, but it is very stiff (so get the cheaper stuff). I am using a longer 1x2 and have my base station higher so I can read at chest level. Also, my 18'x4' AGP has 13 legs, so I started by digging recesses for (13) 12" round pavers that are 1.8125" thick, and calculating in SolidWorks the distance between centers, and scribed a line 18' diameter in the dirt.
You are the only person I have seen with a hilly yard like mine. We have had a pool for 2 years and it is always not leveled. I will use your techniques to level my yard this year. Thank you so much for this video!!!
yeah we have a very oddly graded yard lol
And you are welcome!
Garrett Scott your technique definitely helped THANK YOU !
Hey man, thanks for the video!
What kind of fitting did you use for the tubing on the bucket?
That is amazing. Thanks
Well explained.
Brilliant !
Awesome! Thanks mate! :)
Hey Garrett im wanting to use the water level to level a pier an beam cabin an was wanting to measure from the bottom of the floor joists underneath the house at each pad supporting the joists. I can see how it works on the ground elevations but i would be bringing my stick up to the bottom of the floor joists an trying to read the difference. Question is will it work backwards by using the top of the stick instead of the bottom ?
If the story pole is long enough then it should work. How many feet difference would you estimate between the top and bottom measurement?
I’m getting ready to level our spot for the pool now. Thanks for this video! Later this year we’ll be doing a 10x8 shed and yours looks great! How’d did you do yours?
You are welcome! I used concrete deck blocks for the foundation of the shed. Here is an unlisted video that covers the process somewhat. th-cam.com/video/wJCJGDj_N2Y/w-d-xo.html
wooooooooow! I am so doing this thank you
Thank you!
you are welcome!
hi, what did you use to dig up your area? A tiller?
a shovel and pickaxe. Very tire some. I would recommend machinery!
Materials used to build the water level:
Bucket:
www.lowes.com/pd/United-Solutions-2-Gallon-Residential-Bucket/1000462837
Lid:
www.lowes.com/pd/Letica-9-6-in-White-Plastic-Bucket-Lid/50434790
Tubing 35ft:
www.lowes.com/pd/B-K-1-2-in-x-1-ft-PVC-Clear-Vinyl-Tubing/1000115993
Fitting:
www.lowes.com/pd/B-K-3-8-in-Barbed-Barb-x-MIP-Elbow-Fitting/1000505073
2x4:
www.lowes.com/pd/Top-Choice-2-x-4-x-8-ft-Whitewood-Stud-Common-1-5-in-x-3-5-in-x-8-ft-Actual/1000051161
Black Food Coloring:
Amazon Affiliate Link:
amzn.to/2VgwdbL
or
www.walmart.com/ip/McCormick-Black-Food-Color-1-fl-oz/10309022?selected=true
Gardner Bender Plastic Cable Staples - Around 1/2" :
No link
Drill Bit:
www.harborfreight.com/3-piece-titanium-nitride-coated-high-speed-steel-step-drills-91616.html
Good concept and brilliant tool but it’s much easier to level sand and it will compact
Sand isn't advisable unless a hole is dug first. Otherwise the sand will wash out.
Sand isn't advisable unless a hole is dug first. Otherwise the sand will wash out.
After use, how do u empty the water from the tubing?
No need to empty the water, it won't stain the tubing
I disabled an I’m trying to fix this old moble home it’s a small single wide no blocks under it yet I want to do it myself can’t pay anybody to go it could you tell me how I would use this method an where would my starting point be on the moble home I really need to understand this method if you can help please thank you
Starting point would probably be your lowest point.
What is the diameter of the tubing?
I used 1/2-in x 35-ft PVC Clear Vinyl Tubing
Do air bubs go in tube using this method ?
Only initially. Very easy to bleed them out after constructing it.
Could turn the tape upside down also. Make it dummy proof
I have an Intex 18'x52" round, and I am on my third attempt at leveling the pool. This time, I am going to use a water level, and I like your video the best. I will be putting my level together today, using your video as a guide. Thanks for a great video...and wish me luck! :)
I hope it works out this time!
👍🏽👍🏽👍🏽
Place the zero of the tape measure on the top, so you won't have to read measurements in reverse.
ah, so just read it upside down.
i think string and droppers would be easier but good idea
That's only gonna give you vertical plumb line not horizontal level over long distance
I hate the wind, 2 times i had to start completely over. I hate this design of this pool, and the harware is on the cheap side. That must be the difference between a 2000 dollar pool and a 7000 dollar pool.
This also proves that the earth is flat 👍