Ingenious Valued Secrets, Tips That Work Extremely Well. Construction Industry Tricks and Hacks ▶50
ฝัง
- เผยแพร่เมื่อ 8 มิ.ย. 2021
- Ingenious Valued Secrets, Tips That Work Extremely Well. Construction Industry Tricks and Hacks - Wood Inventions Videos You Must See
==================================
Thanks for Watching, Subscribe and Share!
==================================
►Subscribe UWOODWORKER - @UWOODWORKER
►Subscribe UWOODWORKINGPROJECTS - @uwoo
►Instagram - / uwoodworker
Cooperation, questions: E-Mail - uwoodworker@gmail.com - แนวปฏิบัติและการใช้ชีวิต
Dear Friends, Support Us for More Videos! Click Thumb UP, Share this Video and Subscribe Us.
After Watching this Video, Watch our New Tips and Tricks Video - th-cam.com/video/7HiTdMhgyFw/w-d-xo.html
I like your sanding block. 👍
When you made that zero-clearance insert on the miter saw, you forgot to put a strip of tape on first to prevent splintering.
Just what I observed. Nice one you. However, I’ve used that method for over 45 years so it’s not hard to observe.
Man, a magnet in a bag. Why the hell didn't I figure that out, about fifty years ago? Great vid, thanks.
I use an elastic band around the shaft of the bit for depth measurements, as it saves wiping off pen marks, can be adjusted to move up or down for other depths and slips off easily, once the bit is removed from the chuck.
Great tips, and one-"reverse drilling"-I never would have thought to try.
Works the same with screws near the edges of wood too, run them backwards for a bit, then send it. Keeps the wood from splitting as easy.
@@mikeregier6376 لقرقثقررر۲لثرقققرررقرقل۲ثررلررقرقرقررررد۲ر۲رقردقررثثرررق۲ب۲ر۲ررثل۲ققبقلل۲ربققلقررقلثرقرلدقثبرلرثررثقرررربللثللقل۲قررلث۲رلثقبثلرثر۲ررقدرثقق۲للق۱قرل۲۲رب۲لقرقلثلثثرثثلقلثبللر۲رثلررقلقرقل۲ثثرقثرققثررققرق۲رثرقررققلررقثثثرثرقلرقثررررلقثرررردثقثر۲رثرل۲بقردیق۲لق۲ریقثل۲ثلبل۲لللثثلقققل۲د۲لقرلقلق۲ب۲لرقب۲بل۲قرققلقبلقثقق۲قلرقق۲ققثللثرققلدقلرثلققللقبثرللرلقلثقللثثرقرللثللللق۲لقلرلقبقرقبقلبقلل۲ثللبق۲برلقثللدبللق۲لل۲ثقب۲لل۲لب۱لرثلقرقلل۲ل۲قلقلثللققلقلقللقبثل۲ثل۲قل۲لقل۲بثلب۲ثلب۲۲لللل۲ق۲لقل۲لر۱۱۲ققللبقثلل۲قققل۲ردلللقف۲لث۲لقل۲بققلبلبق۲قبو۲لق۲لا۲لثللللللل۲لقلثقرب۲۲بثلرلللقثللققلثلرقرثلثلقبقد۲۲یلقلفقل۲۲للقللللللققلثرثف۲لثلقلثلثرقلق۲لل۲ثلقرق۲رل۲ثرقر۲ررققلبقثرقلقلقلل۲قثلقلربقل۲ر۲قل۲لثلبلثللل۲قلققثلقد۲لثلل۲قلبقق۲بلقل۲ل۲۲فقققلدقققرلللرق۲لثر۲ف۲۲بلللقبل۲ق۲لقبلرق۲ل۲للب۲د۲قلب۲قل۲ثلق۲قرقبل۲لقرربلدقق۲بلقلق۲۲ف۲بللقلق۲لق۲لقل۲ل۲لل۲۲ل۲ق۲قلل۲قلللقلق۲۲۲ققققق۲ل۲۲۲ل۲دبقثفد۲۲لف۱بللققل۲لقققب۲ل۲۲لققللبفقل۲لق۲لقبقل۱للبثدققالقلد۲فلب۲۲قل۲ل۱قلقل۲۱۲قترق۲ف۲فق۲بق۲لقل۲ل۲۲بللثل۲ل۲ل۲ققللقفر۲فل۲لققردقق۲۲ف۲قر۲۲فل۲فل۲ق۲۲لقل۲للل۲ل۲للل۲للرل۲ل۲۲قللللق۲رثل۲لل۲لب۲۲بلللفثل۲قدق۲۲ببق۲ر۲ب۲ررل۲بلد۲۲لقل۲۲للبثلدلقب۲رقب۲لق۲لل۲بلب۲لبل۲ل۲۲لل۲ررثقر۲لدق۲قللقل۲بل۲لق۲برلثرلق۲لرل۲ل۲رب۲لدب۲ل۲۲قردل۲ل۲ق۲ب۲رر۲للللق۲۲لثلق۲رقل۲رقرقلق۲ففقل۲۲دلب۲ب۲قلقلققثقببققل۲فبق۲ققلب۲رل۲لق۲ق۲ر۲۲لق۲بلل۲ب۲قل۲لق۲ل۲لر۲لر۲لل۲لل۲۲ا۲ققلثلل۱لقلب۲لل۲لرلدققر۲لبلبقرد۲رقرل۲۲فف۲ل۲لق۲بل۲۱ب۲رر۲لقلللب۲ل۲للبل۲۲لق۲للق۲ببث۲بق۲۲ق۲فلب۲ل۲۲۲۲ق۲۲۲ب۲لقف۲بل۲ل۲قل۲۲لق۲لاراتدللق۲بلق۲۲ل۲لل۲ال۲ففق۱ل۲لل۲قل۲خف۱۲۲للل۲ف۲ال۲ل🎷😜😜🎷ا⬆️⬆️⬆️⬆️🤡🤗⬆️🤾♀️🤗⬆️🤗⬆️⬆️🤗🤗💂🏿♂️🤗🤾♀️💂🏿♂️⬆️💂🏿♂️🤾♀️🤗🤾♀️💂🏿♂️🤾♀️😡💂🏿♂️🥁😡🤾♀️💂🏿♂️😡😡💂🏿♂️🤾♀️⬆️💂🏿♂️🤾♀️😡⚽️💂🏿♂️💂🏿♂️🤾♀️😡🤗💂🏿♂️💂🏿♂️😡💂🏿♂️💂🏿♂️🤾♀️😡💂🏿♂️😡💂🏿♂️🤾♀️💂🏿♂️⬆️🤗😡✋✋🥁✋🙇♂️✋🥁🏦✋🥁🏢🥁🏢🏦✋🏢✋😀🏢🏢⚽️🥁🏦✋🙇♂️✋🥁✋🏢🥁🙇♂️🥁🏢😀🏦🏢🙇♂️🔌⚽️🔌🔌⚽️✋🔌🤡😘⚽️🤡😘🤡🤾♀️⚽️😂⚽️🔌🤡🤡🤾♀️⚽️🔌🤡🤡🤾♀️🔌⚽️😂🤡⚽️🔌🤡⚽️🤾♀️🔌✋🤡⚽️🔌🤾♀️⚽️😂🔌⚽️🤡🤡🔌⚽️🔌🤡🤡🤾♀️⚽️🤡🔌⚽️🤡😡😘😘😡🥁🎻🏦🏢🏢🏢🔌🏫🏢🔌🏫🏫🔌🏢🔌🎷🏫🏫😜🔌🏢🏫🔌🏢🔌🏦🔌🏫🏭🏫🏭🏢🔌🏫🏫🔌🔌🏢🔌🔌🏫🎷🏢🏫🔌🏢🏢🏢🏢🔌🎷🏢🏫🏦🏢🔌🏫🏢⚽️🏫🔌🏫🎷🏫🔌🏢😎😅😐🤐😑😜🙃🤤🙃😛😈🧐🤢🥳🤢😿🧒🧒😹😿😿👦😛🙄😘😮☺️😑🤗😮😮🤗🤐😜😐😐😳😢😺👨⚖👨🔧👩⚕️🙍♂️🤦♂️👱♀️👸👩🦰🧚♂️🧙♂️🤵🙍♂️🧝♂️👯♂️🙋♂️🎅👩🚀🤴👨🦲🕵️♂️👦👧😾👴😾👴🙈👩🏫👩🏭👨✈️👨💻👵👩🏫😹👦👨⚖👨✈️👩🏭👨💻👮♀️😾🎅😹🧚♂️👧🧚♂️😹😾😹😹🧚♂️😹😾😾😹😹🧚♂️😹😹🧚♂️😾🧚♂️👦🧚♂️🧚♂️😾😾🧚♂️😹👩💻👩🏭👮♀️👨🌾👩🔬👨🌾👨✈️👨🌾👱♀️🧜♀️🧙♂️👱♂️💂♂️🦸♂️🧜♀️🧝♂️🚶♂️🛀🙍♀️👨🦲👩🦰👱♀️👩🔧👨💻👨💻👩✈️🤴👮♀️👮♀️👨🦲👱♀️👩🦳👳♀️👱♀️👼👳♀️👩🦳👳♀️🤴🙀👻🙈👴😿😹🧒😹👸👩🦳💂♂️👸💂♂️👩🦰🧙♂️🧙♂️🤵👼👳♀️💂♂️👩🦳👸👱♂️👩✈️🧒💀👨💻👨💻👮♀️👩🏭تفقق👮♀️👩🏭👨💻👩🏭👮♀️👮♀️👩🏭👩✈️👮♀️👨🎤👨💻👨⚖👨⚖👨⚖👨🔧👩⚕️🧑👨⚖👨⚖🕵️♂️👦👩⚕️👩🔬👩⚖👩🔬👩🔬👩⚕️👩⚕️🙈👴👦👦🙈👴🙈👦👨⚖🧑👨💻
Reverse drilling also works well when trying to make a hole bigger with a spade / helical drill bit. Otherwise it can jump around too much.
So simple but so effective, thank you,
thanks for your nice ideas
Can we just acknowledge the fact that he has a log vacuum? 😀
Doesn't everyone? LMAO 🤣 🤣
I will never be worthy from now on , I only have a Kartcher Vac
@@13yearsaprepperr.jtilbury.51 - They always says the first step to fixing a problem is acknowledging it 😆
We MUST!
How else would you vacuum up logs? 😆. And yes, i am the only one who thinks I’m funny , ask my wife.
When cutting some plywood or melamine with a jigsaw I use the downward facing toothed jigsaw blade. Great for cutting out holes in laminate bench tops as well. Just remember to have the blade going straight up and down.
merci beaucoup pour la vidéo
I've been using old microwave magnets for years now,I always wear bibs and I keep them in the breast pockets to hold nails,screws,staples and tools
ЛАЙК!!! УСПІХІВ та ЗДОРОВ`Я.
🤝 взаємно!
Finally tips that are practical and useful. Please more!
Ok🤝
really?
you havent done much working then
@@redwarf8118 your right, thanks for pointing that out
Hola saludos excelente muchas gracias bendiciones
Some were gold; new subscriber. Wedged dowel 👍 Show us the “log” vacuum! Show us that sanding block!
Des travaux ingénieux faits avec soins ! Bravo et Félicitations ! Patrick (France)
excellent, love the drilling wood in reverse before drilling it. thanks for uploading
Oddly satisfying. Thanks for posting.
I love that ✏️ and sand paper trick! I hate trying to line that shit up!!! Just brilliant 😀☺️
If you have to use pencils to line up a small sandpaper disk, you probably should not be using power tools or any sharp objects, including pencils.
Theese are carpenter basics.
But yes, they are absolutely necessary for good quality!
Consejos muy útiles. Gracias.
Thank you for sharing this.
thanks for add great tips
Very straightforward and handy tips. Thank you!!
Thanks
👍🙏
Perfeito...Parabéns...boas dicas
Actual good tips on TH-cam! Thanks so much!
Sincèrement c'est une video très utile ..mieux que des millions de conneries sur TH-cam ...je vous remercie beaucoup ...may God bless You....I watched this video with a big pleasure...I am supporting you from now ...
Pure skills... thanks for sharing. Great and smart job !!
All these tips are awesome! Very knowledgeable! Thanks
Bravo trucs utiles et faciles. Merci.
Seen lots of these videos. This one is the best by far. All practical. New subscriber 👍
Thanks 👍
Exactly! Me too.😇
Hey 👋 great 👍effort 👏 . Keep it up
Muy buenos todos esos tips. Gracias. Saludos desde las sierras de Córdoba Argentina...!! 👍👌💪🇦🇷
Ooh, thanks a lot !!! My greetings to Córdoba Argentina
Can someone explain the last segment with the dowels? What was the purpose is what I’m asking about
Yes, that dowel is now super tight. I will use that tip often!
Legs for tables or benches.
The dowel is split and has a wedge put into it. The wedge makes an extremely tight joint that won't loosen over time. It pulls the materials together and then locks it. This type of joinery is used for kids toys. You avoid nails and screws that can, and eventually do, come out.
If you make one, remember to cut the incision perpendicular to the grain, otherwise you risk splitting the entire dowel/leg/whatever you're trying to fasten :)
When you "fold" a band saw blade step on the open loop, twist twice and push down to the floor.
in this video, this is the second way.
the first one has already done - th-cam.com/video/YjlMHwGdqjo/w-d-xo.html
@@UWOODWORKER Haha, one of the first tasks i had to learn when i was working as a service tech, i got a band saw, i was told to unpack it and then twist it back again ;)
Scary thing when those teeth pass your throat;)
Good, you can pick up your fingers while you’re down there! 😉
@@Schlemiel-schlimazel Hehehe, you can live without fingers. It's way more difficult to live with half of a wind pipe ;)
@@ogi22 depends on which way you cut it!😊
Muy pero muy bueno felicitaciones.
Świetny I niezły pomysł jest stąd podkładką pozdrawiam twórcę tego filmiku 👍👍👍👍
I like your sanding paper block
Amazing tips!!! Thanks!!!
Thanks for watching!
Excelente labor muy útil 👍👍👍👍
Great idea!
3:36 Love the shop vac housing!
Thanks for the great tips! 😍
This dude is very lucky to still have all his fingers . They were way too close to the blade using both mitre saw and table saw .
Thumbs UP for content. These are usable tips for the new and average woodworker. I doubt professional will subscribe. Your tips are valuable to the majority of your viewers. Two of these will be used regularly in my shop. Many thanks!
3:45 Also works for weed spilled onto carpet🙂
I once saw the lady next door vacing the driveway to her house ,, I thought thats anal as !
Then my wife told me she dropped her bag of pot and was trying to save it
Sure the tape helps with the jigsaw but slow down and let the tool do the work and the second half would not look as bad
Very interesting tricks. Thanks, I learned a lot.
Excelente. Gracias!
Kilka bardzo fajnych rozwiązań
Beautiful 👏
If people only take 1 thing away from this video, you have served a purpose. For me, the reverse drill is my take away. Keep those handy tips coming, as they're, err, handy ;-D
Excelente vídeo amigo saludos Colombia
that wire splice is called The Western Union Splice.
How strong is that last joint?
Not very strong, more decorative
At last the tricks are being shown. 😁♥️
А зачем я это смотрю?
Один вопрос, шприц с пластмассовым клапаном где нашли? В наши дни.
Voilà un génie au service des autres .bravo
多くのアイディアに秀樹感激Goodです=3
Thanks for watching our channel!
These sort of videos are really a bit boring. We've seen it all a dozen times.
Then i watched this one. I reckon 80-90% of tips were new to me! Well worth a subscribe I think.
We are trying. Thanks for the support!
i dint understand the filler one? if your sanding the grain it will go smooth anyway without filling and sanding
Thought the same
I didn't get the washer and oil one, really what the point of the washer was
@@CLove511 To keep the oil around the drill bit and not flow away.
Use a piece of masking tape to make a flap for the depth guage of your drill bit, it will clear the dust as well as being easier to see when you are to depth.
I don’t have time for all these time saving tips
Finally somebody with some good useful Tips, instead off the usual often highly dangerous hacks
Thanks!
WOW loved it
Great tips! You should consider getting a flush cut saw. Saves a lot of sanding time on those split plugs.
Bien lo tuyo, Tulio!.
Very clever!
Brilliant brother,thank u for sharing,will be a great help for ignorant people like me.
Some new, some old, at least for me, but I really like the sand paper holding block which you used sand the end of the board to which you applied the wood filler.👍👍👍👍
The reverse drilling made my chin drop.
I've used that when drilling through a floor covered in carpet . Once through the carpet then go back to forward. No snagging.
Если мастер сдувать опилки ртом это не мастер!)
Amazing 👍👍👍👍👏👏👏👏
*very good video, my channel fan greets you, wish you a good week*
wondafull!!!
Some I knew, some were new. But all good tips.
Sou fã disso
These are great tips and hacks that work! Ironically I’m working on something similar but different tips that will roll out soon. This is great and keep up the solid work so we can continue to inspire others to build something awesome! 👍🏼
OK pretty good but are most worth the set up time?
Especial,gran video
ALWAYS AWESOME TIPS!!!
cool stuff
Lụm mấy cây đinh maf phải dùng máy hút bụi KKkk . dư năng Lượng khoan cái lổ phải làm nhiều thứ đến Vậy kK
Niby proste, a świetne porady. Dziękuję... subskrybuję. Pozdrawiam.
Полная хрень... Всё что показано как ноухау, очевидные вещи...
Great works...i subscribe today...
Thanks friend
Great video and tips - but when it comes to safety, if you’re going to cut something so small on the mitre saw, I’d advise to make a jig with sandpaper on top of this ( just a flat wide piece of thin MDF or Plywood that sits on top of the mitre saw surface and held in place with clamps), then also cut a stick of wood with sand paper covering it. Both of these used in conjunction can hold that small piece safely. Your fingers should never be that close to the blade - yup, it may have been okay today, or maybe tomorrow, but at some point your luck will run out. Safety first, my friend.
a normal craftsman would just use a hand tool for such a small piece.
@@BigKelvPark some times when I'm working in the heat I'll grab the biggest tool to cut the smallest piece. If you're gonna be dumb, you better be tough. I need to quit scheduling decks and outdoor kitchens in the summer. Texas heat ain't no joke, c'mon!
Great call on the sandpaper. I'm going into my shop to make a jig right now and I'll try some 300 silicone carbide since it's pretty even in thickness. Aluminum oxide paper is a bit spotty but the difference is probably so miniscule it can't translate into the work under 1/100th
@@roadiejames Is that 'biggest tool' between your legs?
@@BigKelvPark lol I am 6'8"........ So it's probably my feet 😂
Your sanding block looks like it would be a great tip on how you made it
А что нового? Просто плагиат!
Pretty good tips, although I don't understand why he taped the washer to the metal piece before drilling the hole, unless it was just to keep the lube oil from running off. Also, taping wood laminate before sawing helps, but it's better to score it with a sharp knife first, get much cleaner cut.
By this you are helping us, and we are doing new content for you!
Handwerklich Prima Tipps 👍👍👍👍👍
6:54 Damn your hand was SOOOOOOOOO close to the blade I got goose bumps !!!! Take care man !
What kind of tape are you using?
Brilliant
I am very glad you liked it!
05:16 why not use tape when cutting the wood insert of the miter saw, that way you don't have to sand the edges?
Здравствуйте Специалист по дереву,ролик по ремонту ДСП,от 10 мм,сколы,вкрючивание саморезов уже в расшатанные отверстия,с ответом подпишусь😄а так всё гуд 👌!!!
Подписывайтесь 😀
5:22 If the zero clearance insert isn't exactly the same thickness as the groove, you will have accomplished nothing. And that critical step was NOT shown....
Yeah .. I also miss something here.