As long as overlapping joints of the plastic sheets are facing towards the back of the boat and the seams are sealed with a waterproof silicone adhesive... the boat should last quite a long time.
Now reinforce the outside of the hull with fiberglass for rigidity and sealing all the leaks that will come up when the mechanical resistance of the water roughens up and thins the plastic. The workmanship was good... But there is a best practice to making anything that floats on the water that significantly reduces the potential for accidents and/or failures in the material/construction.
@@RichardLucas I can't imagine using one of these boats in open sea, that leaves bays lakes and rivers, the domain of pontoon boats. The only requirement that would be better served by these is small size. Oh and speed.
Ładny projekt łodzi! Ta, wykonana przez ciebie jest fajna ale wykonana wg. mnie dopiero w połowie. Brakuje przede wszystkim podłogi oraz zabudowy burt od środka. Bez zabudowy podłogi, stanięcie nogą na dnie łodzi grozi po prostu jej rozerwaniem i zatonięciem! Pozdrawiam
The video was incredibly informative and inspiring. Watching the entire process of building a boat from plastic barrels and wood was fascinating. Thank you for sharing such a creative and eco-friendly project. Highly recommended for anyone interested in DIY projects!
On peut faire un bateau avec a peu prés tous type de matériaux, il faut tenir compte de la résistance, du poids et de la facilité a mettre en œuvre. le gars fait avec ce qu'il a sous la main, des barils en plastiques, mais disons-le clairement ce n'est surement pas la meilleure solution, la fibre de verre, le bois ou l'alu seront évidement bien préférable plus durable et fiable! bravo tout de même pour le travail et la patience! Je vois tout de même un inconvénient majeur sur cette réalisation, indépendamment de l’étanchéité qui pourrait être moins bonne a longue échéance, il n'y a aucun fond de sol rigide et si on pose les pieds sur les ptastiques en dehors des longerons de bois, il y a fort a parier qu'on pourrait passer a travers ou affaiblir l'assemblage.
This is pretty cool, not sure how safe these boats are compared to boats created in traditional materials such as various fibber or just wooden boats. I can imagine these are ok on rivers, but how does that plastic handle sea water? Also I think an improvement would be to use a heated wire cutter to cut plastic or a similar tool. And recycle the scraps too. Using a saw creates a lot of plastic dust, which is both bad for environment and everyone else, while also being very bad for the worker(s). Of course, just reusing the barrel for their original purpose would be an even better use.
That's a pretty awesome build. I don't know how we expected that not to leak. I think I put a roll of butyl and some stainless screws in. Let's go fishin!!
It is better to weld the seams using a soldering iron and pieces of plastic. Polyethylene terephthalate should be welded. Or you can seal them with silicone sealant. Well, or spend 5-10 bucks on one or two layers of fiberglass, and also make a deck from the same plastic to make it easier to remove water, and add weight to the bottom to make it harder to turn over while standing on the water..
My neighbor who was a brainiac made a catamaran using oil drums halves back when they didn't have plastic drums. He put them 4ea long ways and brazed them together Then added copper tubing over it. He reinforced the hull by also bridging it with copper tubing. When he was done he sprayed the bottom a lot of coats as he did with the inside. He put an aluminum wave shield in the front. He put a 20hp motor on the starboard side as he operated it on the port side. The first trial checked out but it was completely under powered. So he kept increasing the Hp until the boat balance out. Eventually heard it sank due to an retaliation for stealing someone's girlfriend.
ধন্যবাদ ওস্তাদজীকে আমি ১৯৯৪/৯৫ সাধু যোসেপ কারিগরী শিক্ষা গ্রহণ করেছি লেদ মেশিনে প্রশিক্ষণ নিয়েছি এখও এ কাজে নিয়োযিত আছি আপনার কাজে প্রসংশা করি খুবই চমৎকার হাতের কাজ আপনার।
Excellent travail simple et moins cher je note 20/20 , j'aimerais bien si quelqu'un peut transmettre ça à nos frères en Afrique .Le bois augmente de prix.
Что то грызут меня сомненья что все эти соединения при помощи гвоздей будут достаточно хорошо держать , особенно в полу лодки когда люди начнут туда наступать изнутри давя на пластик рядом с деревом
Мужик молодец, рукастый. Однако инженерная составляющая слабовата- у лодки нет единого жёсткого каркаса, а потому вся конструкция получилась хлипкой, и для нормального использования не пригодной
@@ВладимирДавыденко-ь8ю бочка у нас стоит 200💲еще за доставку 🚚 нужно будет заплатить минимум 400💲 . Чтоб лотку сделать нужно 4 бочки . Теперь сложите четыре раза по двести и плюс четыреста за доставку . Листы ПНД три метра длиной и шириной полтора метра . Цена примерно 300 долларов . Нужно примерно три листа , доставка из магазина до подъезда бесплатно .
Trimakasih kawan videonya sangat bermanfaat,,, proses membuat perahu dari bahan drum plastic yang bagus sekali❤❤❤❤❤❤❤
HDPE can be weded with hot air gun and is guaranteed 100%waterproof. With the nails sooner or later water enters
Great Work. Thanks and Best wishes from North West England.
I think your boat needs an inner shell as a floor cover. In fact, the body should be two layers.
I really don't think that butt jointing the wooden frames and nailing some plastic patches on will last very long.
Как обработать, минимум 10 лет может прослужить
水の抵抗の恐ろしさを知らぬ…愚か者だよ…
Butt joining would then leave you dependent upon the strength of the wood splitting so he likely lapped the panels which would be very strong.
As long as overlapping joints of the plastic sheets are facing towards the back of the boat and the seams are sealed with a waterproof silicone adhesive... the boat should last quite a long time.
Nails? Agreed!
Now reinforce the outside of the hull with fiberglass for rigidity and sealing all the leaks that will come up when the mechanical resistance of the water roughens up and thins the plastic.
The workmanship was good... But there is a best practice to making anything that floats on the water that significantly reduces the potential for accidents and/or failures in the material/construction.
Fibreglass over barrel plastic would delaminate. The barrels with sealant would be monocoque by themselves. Avoid over-engineering
It defeat the purpose of making this a cheap and easy project tho
Good luck making anything stick to polyethylene.
@@peternicholsonu6090 Varela are pvc? Both polyester and resin grab that.....
@@linusgoblinthis is far from cheap. Barrels are pricy and this won't last. So.. pointless
While good work the best use of these barrels is in pontoon boats.
They're great for floating docks too.
@@vertstang123 Good point.
@@RichardLucas Obviously not the best pontoons but best use of these drums in boat form. Sealed cells that for the most part just need mounting.
@@RichardLucas I can't imagine using one of these boats in open sea, that leaves bays lakes and rivers, the domain of pontoon boats. The only requirement that would be better served by these is small size. Oh and speed.
The best: Straw for storing brandy
Oh boy, please collect the micro plastics you create with the saw! Peace and love!
Ładny projekt łodzi! Ta, wykonana przez ciebie jest fajna ale wykonana wg. mnie dopiero w połowie. Brakuje przede wszystkim podłogi oraz zabudowy burt od środka. Bez zabudowy podłogi, stanięcie nogą na dnie łodzi grozi po prostu jej rozerwaniem i zatonięciem!
Pozdrawiam
Creative man and great work
Keep innovating the world
He needs work like this
Economiquement intéressant ,mais le problème c'est que rien ne colle sur le polyéthylène , donc pas facile de faire l'étanchéité !
That's why it welds together. A soldering iron will help. Well, epoxy resin, as well as polyurethane, PUR.
Remember how plastic water pipes are connected)
아주 멋진 배 입니다. 저라면 플라스틱과 목재 사이에 고무 타이어 조각을 넣어 밀봉을 할것 같습니다....
А он так и сделал.
Excellent effort , viewing from Detroit Michigan USA 🇺🇸
Great job, you're a genius ! Where are you located ?
The video was incredibly informative and inspiring. Watching the entire process of building a boat from plastic barrels and wood was fascinating. Thank you for sharing such a creative and eco-friendly project. Highly recommended for anyone interested in DIY projects!
On peut faire un bateau avec a peu prés tous type de matériaux, il faut tenir compte de la résistance, du poids et de la facilité a mettre en œuvre.
le gars fait avec ce qu'il a sous la main, des barils en plastiques, mais disons-le clairement ce n'est surement pas la meilleure solution, la fibre de verre, le bois ou l'alu seront évidement bien préférable plus durable et fiable! bravo tout de même pour le travail et la patience!
Je vois tout de même un inconvénient majeur sur cette réalisation, indépendamment de l’étanchéité qui pourrait être moins bonne a longue échéance,
il n'y a aucun fond de sol rigide et si on pose les pieds sur les ptastiques en dehors des longerons de bois, il y a fort a parier qu'on pourrait passer a travers ou affaiblir l'assemblage.
SUPER IDEA . POZDRAWIAM .
More work than necessary. I would have made a couple of pontoons, built a frame and structure on top. Mounted a motor and been on my way.
He is a true craftsman. Incredible!
Nicely done! The difficulty is all the woodwork to get a solid wooden frame.
This is pretty cool, not sure how safe these boats are compared to boats created in traditional materials such as various fibber or just wooden boats. I can imagine these are ok on rivers, but how does that plastic handle sea water? Also I think an improvement would be to use a heated wire cutter to cut plastic or a similar tool. And recycle the scraps too.
Using a saw creates a lot of plastic dust, which is both bad for environment and everyone else, while also being very bad for the worker(s).
Of course, just reusing the barrel for their original purpose would be an even better use.
Love it . Looks easy enought. Built a few boats out of plywood, this looks great.
That's a pretty awesome build. I don't know how we expected that not to leak. I think I put a roll of butyl and some stainless screws in. Let's go fishin!!
Keep up the good work ...love making...
Hadir nyimak salam kenal dari kisaran city Asahan Sumut Indonesia 🇮🇩🇮🇩
최고 멋진 보트제작영상
잘보고 구독하고 응원하고갑니다
최고십니다
So creative. Fantastic.
HELAL OLSUN. Çök güzel.
It is better to weld the seams using a soldering iron and pieces of plastic. Polyethylene terephthalate should be welded. Or you can seal them with silicone sealant. Well, or spend 5-10 bucks on one or two layers of fiberglass, and also make a deck from the same plastic to make it easier to remove water, and add weight to the bottom to make it harder to turn over while standing on the water..
Greetings coming from Indonesia, healthy greetings and creative greetings
My neighbor who was a brainiac made a catamaran using oil drums halves back when they didn't have plastic drums. He put them 4ea long ways and brazed them together Then added copper tubing over it. He reinforced the hull by also bridging it with copper tubing. When he was done he sprayed the bottom a lot of coats as he did with the inside. He put an aluminum wave shield in the front. He put a 20hp motor on the starboard side as he operated it on the port side. The first trial checked out but it was completely under powered. So he kept increasing the Hp until the boat balance out. Eventually heard it sank due to an retaliation for stealing someone's girlfriend.
Very good job I likeit
I think your boat needs to be another 15 foot longer!
ধন্যবাদ ওস্তাদজীকে আমি ১৯৯৪/৯৫ সাধু যোসেপ কারিগরী শিক্ষা গ্রহণ করেছি লেদ মেশিনে প্রশিক্ষণ নিয়েছি এখও এ কাজে নিয়োযিত আছি আপনার কাজে প্রসংশা করি খুবই চমৎকার হাতের কাজ আপনার।
Excellent travail simple et moins cher je note 20/20 , j'aimerais bien si quelqu'un peut transmettre ça à nos frères en Afrique .Le bois augmente de prix.
👍 excelente y éxitos
Wouldn't take it offshore or out of sight of land. Always wear a life vest.
Very nice!
Amazing very nice boat making
No deck inside? I'd probably step right through the hull... With all those tacks, this would be for calm, fresh water lakes only!
Deffo fit for purpose 😊
👍🏴😁✌️
wow very nice lake
Что то грызут меня сомненья что все эти соединения при помощи гвоздей будут достаточно хорошо держать , особенно в полу лодки когда люди начнут туда наступать изнутри давя на пластик рядом с деревом
Amazing tanks perkonsian nya cukup sempal best k
Araújo caiaque do Brasil
L'idea è buona ma la realizzazione è a tutti gli effetti insufficiente.
Comunque complimenti per l'impegno che hai dimostrato.
Saluti
...and it creates microplastics with the saw blade cutting through the plastic.
Goose wasn't bothered by the guy sawing right next to it.
It was trying to get out of there - 1:33. It was distracting from the boat build.
1:00 I'm glad i'm not the only goose watching this!
ich Liebe auch diese PE Tonnen daraus kann man viel Machen unkaputtbar
Thanks for sharing sir Godbless
Genial!!.😅
слишком легкая, такие манёвры могут привести к перевороту, надо делать тяжелее.
So did you just steal this guy's video and narrate over it?
Did anyone else see a duck in the garage? He was looking on with those wee beady eyes.
whats wrong with screws instead of nails?
Bare minimum is ring shank nails. No way I'm risking my life with 1000 little tacks
Verry nice
Como proceder para ver experiment nav egabilidade de um desses barcos?
Benar berarti bagus😂🎉
wow... good job.
Cool 👍
That barrel he had in the front was full of water, the boat is too light for that motor and was trimming up way too high.
Hay lắm xin cám ơn bạn
Did not see any waterproofing did not see any silicon it would leak water.
Nice boat
how does this not leak?
What about the Kill Cord?
Cheaper to just buy a boat . Here in Tampa used plastic barrels are $100 each
Hahaha 20 here!😂
Just got 6 barrels for 60
A Ship!! Lmfao 😂
It's a canoe! 8hp way over kill for that with a flimsy transom!
Crazy and dangerous!
На коленке, из говна и палок, Человек делает настоящую лодку лодку!
Genio
Recycling isn't using working barrels :D
最多玩幾日,隻船肯定自己解體!成隻船嘅結構只不過比模型船好少少!但模型船吾會坐人!😲😲😲希望佢自己用好啦,吾好害人😐😐😐😐😐😐!
Everyone has not been on a boat at some point in their life. you are extremely privileged.
Yeah yeah, but shop duck! SHOP DUCK!
help the environment by recycling (uses only new barrels) lol
ไม่ทนทานเป็นมลพิษต่อสิ่งแวดล้ม
Need some fiberglass now
В следующий раз сделайте и говна и палок!
Сделать пол.
А так нормальня лодка. Плтхо что пластик недолговечный.
접합부들 틈 사이로 물이 안 세게 하는 방법은 안 나오네. 가장 중요한 과정인데 ㅎ
İskelet sağlam olmazsa bogulursun reis...
Кажется в стыках не совсем герметично , или " все лодки текут - знай себе вычёрпывай " . Не мне плавать на ней .
So how did he really seal that PP?
with spit
Norm for river
I am wonder, where can I get these plastic barrels ?
Intelligent
Jika rumahku dekat pantai pasti kubuat
Мужик молодец, рукастый. Однако инженерная составляющая слабовата- у лодки нет единого жёсткого каркаса, а потому вся конструкция получилась хлипкой, и для нормального использования не пригодной
плюс не раскрыт вопрос водонепроницаемости
الترجمة تحجب المشاهدة
All that chemical leaching off into fresh water ways doesn’t seem ethical
not a ship it's a boat
техника безопасности почти нет . обтекаемость очень слабая.слишком лёгкая на развороте перевернётся.
Дешевле купить ПНД , чем бочку бу .
1 бочка это лист 1.6 Х0.8 цена 10 долл . 1 лист ПНД 8мм в 5 раз дороже
@@ВладимирДавыденко-ь8ю бочка у нас стоит 200💲еще за доставку 🚚 нужно будет заплатить минимум 400💲 . Чтоб лотку сделать нужно 4 бочки . Теперь сложите четыре раза по двести и плюс четыреста за доставку . Листы ПНД три метра длиной и шириной полтора метра . Цена примерно 300 долларов . Нужно примерно три листа , доставка из магазина до подъезда бесплатно .
Super
I think you need to make original content instead of stealing views from other creators.
দাম কত জানাবেন
eso no tiene la categoría de barco. Es un objeto flotante.
Ich sehe nur Mikroplastik
De eenvoudige Indonesiers was al lang begonnen
Out koek.😅En 😅