FM 200 FIRE EXTINGUISHANT AND SUPRESSION SYSTEM

THE USE OF THE EXTINGUISHANT PANEL,HOCHIKI,VES,AVENGER WITH KIDDIE CYLINDER

[@bruce254]

This is amazing...now i understood everything.Thanks big🙏

[@ManjeshKumar-qy7zh]

Sir you are good video make video it video is very helpful for us

[@amarjeetravidas6466]

Excellent 👌

[@edwaynemago2633]

to reset the solenoid use the proper resetting tool and use the fm200 preventive maintenance checklist

[@makofficialvlog2676]

Nice❤

[@Dime_Bar]

Very good video thanks 👍🏻👍🏻👍🏻

[@michelmambueni4289]

Les explications sont claires malgré vous ne parlez pas français, étant expert.je comprend parfaitement...

[@engineersguide4249]

BON À ENTENDRE ET MERCI POUR LE COMPLÉMENT

[@engineersguide4249]

VA FAIRE DES SOUS-TITRES FRANÇAIS QUAND IL Y A PLUS D'ABONNÉS FRANÇAIS LOL

[@RolandOrapa-dr6hl]

what is the comnon trouble of this panel . sir
gobless po

[@gelovlog9361]

Its possible to remove the supply or signal from c. Panel to solenoid so no need to rmove solenoid valve thanks

[@engineersguide4249]

it is possible but to check the activation of the solenoid wont be applicable, and you have to get another EOL to normalize the panel..

[@Matrickz]

where is the link you said in the part of your video on how connect or wiring that panel can you please share with me

[@yasararafath3184]

If i torn the manual side that time alarm activated time FM-200 will be released or not!! Can you tell me about please

[@engineersguide4249]

if what you saying is activating the manual release then its yes it will release in zero secs

[@samsumaila8654]

From the cylinder

[@mdsahinalam9537]

Friends what's your company name ? Plz

[@samsumaila8654]

Please which spanner size can be used to remove the solenoid

[@engineersguide4249]

solenoid is supposed to be hand tightened not with a spanner

[@erickm6781]

Hi plz
How to do if I need training for automatic fire suppression system ?

[@engineersguide4249]

you can message us directly

[@twahashearer8302]

​@@engineersguide4249please share your email, very helpful demonstration

[@falcond214]

Can you share how you cleared the fire zone lights on the panel please?

[@engineersguide4249]

You need to reset it by pressing the processor reset button below the key enable switch ... Just give me a feed back after it's done ✅ TNx

[@falcond214]

@@engineersguide4249 press reset when the alarm sound is working? Or first I clean the detector and then press reset?

[@engineersguide4249]

You can only reset when the system is not in discharged mode ..but if it discharges u need to hard reset by resetting through the pressing of processor reset

[@engineersguide4249]

@@falcond214 you can silent the system, clean it then do the reset to avoid continuous alarming

[@dadabhai5854]

😆😆😆😄😄 very easy this system

[@yathi262]

Where & how to connect Manifold Discharg Pressure Switch?

[@engineersguide4249]

any where just above the union at the cylinder and for the panel side tell me the kind of panel you are using

[@shafiqmughal1115]

I need information abort switch said termintion

[@engineersguide4249]

NO WORRIES JUST TELL ME THE ISSUE AND WOULD BE GLAD TO HELP YOU OUT ..FOR THE TERMINATION ITS JUST CONNECTING IT TO NORMALLY OPEN WITH YOUR END OF LINE RESISTOR FIXED

[@azazulahmad8693]

How to connection with hvsc fan

[@engineersguide4249]

It's always advisable to get a relay when u want to connect any fan or damper