Mr Chad. Love watching your videos. I have a question for you sir. Im going to be restoring my truck. Im looking at purchasing a good but budget friendly Corded DA Sander. What are your thoughts and what would you recommend.
Happy birthday Doug!! The floor looks awesome Chad. Nate did an awesome job helping you bead roll them panels. This car deserves to be painted to be honest. Awesome video Jolene!!!
My husband and I bought the exact same model and year coupe about 33 years ago. It had a few more parts, but looked much the same. We always wondered whether we should chop it, but hesitated because we didn't know what it would like like, but now we know we will chop it because we can see exactly how it will look. We have loved every episode of the build on this car, because we can use this as a guideline to do the rebuild on our car. Hopefully we can retire out soon so we can get the time! GREAT JOB on this, Chad and Jolene.
Don't listen to idiots like Stephen. It will be fine. Some people just like to pretend they know everything. If it's what you would like, chop away and enjoy
@@stephenk79-rc1il A typical wannabe who's mad because he can't make people think he knows everything and actually has experience and knowledge about this stuff. It's just sad really but maybe someday you'll grow out of it. We all mature at some point you'll get there too.
For me watching your Bad Chad channel and Jolene’s jolene channel is like going to automotive school I can learn lots of techniques watching you(Bad Chad), Nathan, and Douglas
To be clear, love the channel, content is awesome, love Chad, the Queen and the crew. But when Chad stops welding to inspect every single individual spot weld when clearly the panel is flat it seriously screws my ocd..🤣 just weld the sucker !!! 🤣 you are good sir !! You tack well sir !!! Pull the mutha effin trigger son !!!!! 🤣 love your work. 💯💯💯
You could cut a 2 inch strip of that steel sheet, brake it at a 90 and half a 1” flange on each side. Plug weld em together and no need for square stock along that bottom between the “studs” or leave a bit of excess on that flat panel next time and bend a flange on it.
Motor and trans should have been lower in the frame that drive shaft tunnel would have been lot smaller more room for seats and better drive shaft angle
Your honestly one of the only channels that actually shares and shows us what to do. I would like to see the last couple cars finished, like the hot wheels car and i definitely wantvto see this done
I didn’t realize that your square tube skeleton wasn’t fully welded to the frame. That it will be cut free from frame and floor will go with the body. It’s not ingenious, simply the RIGHT way to do it !!! Great job Chad 👍🏽
I'm watching the bonus episode with Chad welding to nice music. Iust say that I'm enjoying it so much more than the tutorial and constant cutting and grinding. It's actually relaxing. I'm still watching instead of fast forwarding.😊
Eyeballing cuts is one of my favorite activities to do. I’m a tinner by trade but not hvac. Architectural sheet metal copper roofs and such. Dabbled in bodywork for a short while and enjoyed the shit out of. Would love to get back into it slowly building up my tool supply so when I do work on my truck I can go full send. Like how ya work man. Good stuff.
Bad Chad, the fabrication of the square stock and then floor panels is absolutely brilliant. You get a vision in your head and you are able to build what your vision is !! That’s remarkable in my book….🤟🏼✌️😎🥇🥇
Chad & Jolene, I hope you enjoy your Saturday evening! Chad I noticed that Rooster said the same thing as I was thinking. Which is that I would screw the top down on the console in case you need to get at the shifter without getting under the car. Also, I have already said that for Jolene's safety you should make a drive shaft hoop! It is easy for you to make in 15-20 minutes and it is made of heavier metal than the floor and it will stop the driveshaft from coming through the floor and hurting someone racing the car! Jolene great work as always, you do such a good job with the camera, the video, and the production of it all!
I cant say I fully understand this concept but I see it as a great learning opportunity and look foward to seeing the progression, rooting for your success.👍👍🇺🇲
Enjoyed this sunday programming over breakfast! Great job chad! Keep on truckin'! Jolene's camera work is impeccable!❤❤ keep up the excellent content! Many blessings!❤❤❤😊
Makes total sense why you are building it the way you are, people just love making negative comments. Trying to bring you down is easier than trying to build themselves up.
G'day Bad Chad, I think this build is really coming together nicely. The only thing that concerns me is the top console panel and the gear leaver. Fixing the panel could cause problems removing the gearbox. Thanks for sharing the knowledge man ✌️ Peace from Melbourne Australia.
🎬 WATCH the bonus episode here: th-cam.com/video/9OfW85KUpWE/w-d-xo.html
Mr Chad. Love watching your videos. I have a question for you sir. Im going to be restoring my truck. Im looking at purchasing a good but budget friendly Corded DA Sander. What are your thoughts and what would you recommend.
Thank you, Chad and Jolene for the continent. I sure appreciate watching it.
Happy birthday Doug!! The floor looks awesome Chad. Nate did an awesome job helping you bead roll them panels. This car deserves to be painted to be honest. Awesome video Jolene!!!
Chad you are so right. You are a great teacher!
You are a good teacher, step by step and the reason for each step.
My husband and I bought the exact same model and year coupe about 33 years ago. It had a few more parts, but looked much the same. We always wondered whether we should chop it, but hesitated because we didn't know what it would like like, but now we know we will chop it because we can see exactly how it will look. We have loved every episode of the build on this car, because we can use this as a guideline to do the rebuild on our car. Hopefully we can retire out soon so we can get the time! GREAT JOB on this, Chad and Jolene.
Don't listen to idiots like Stephen. It will be fine. Some people just like to pretend they know everything. If it's what you would like, chop away and enjoy
@@stephenk79-rc1il A typical wannabe who's mad because he can't make people think he knows everything and actually has experience and knowledge about this stuff. It's just sad really but maybe someday you'll grow out of it. We all mature at some point you'll get there too.
@@stephenk79-rc1il We'll have our professional welder nephew do it and it will work.
The floor is looking really great
Love the show! I watch it all the time.😊
What a transformation it looks awesome
I'm always amazed at how much work you get done in a short period of time.
Looks really good Chad! Cheers
Thanks for sharing with us
Watch every night , enjoying the show , you guys work so hard but produce a quality show 👌👍
It really is a very smart way of doing it fast simple, and gets the job done
Another great video! Thanks for sharing!
Thanks for bringing us along Bad Chad, this floor and suspension work has taught me a ton!!🤩
Great work.
For me watching your Bad Chad channel and Jolene’s jolene channel is like going to automotive school I can learn lots of techniques watching you(Bad Chad), Nathan, and Douglas
To be clear, love the channel, content is awesome, love Chad, the Queen and the crew. But when Chad stops welding to inspect every single individual spot weld when clearly the panel is flat it seriously screws my ocd..🤣 just weld the sucker !!! 🤣 you are good sir !! You tack well sir !!! Pull the mutha effin trigger son !!!!! 🤣 love your work. 💯💯💯
The Floor looks awesome. Great Job.
You could cut a 2 inch strip of that steel sheet, brake it at a 90 and half a 1” flange on each side. Plug weld em together and no need for square stock along that bottom between the “studs” or leave a bit of excess on that flat panel next time and bend a flange on it.
Happy birthday Doug!!!!
Floorboard looks great.
You make it look so easy. Love it!!
Happy Birthday, Doug. And many, many more!
Looks awesome,good job Chad and Joline
Looks amazing. You have helped me so much with my project. Thank you
Crazy angle on the driveshaft
needs to drop the rear of the gearbox down
It will change after the body weight and rest of parts are put on
Motor and trans should have been lower in the frame that drive shaft tunnel would have been lot smaller more room for seats and better drive shaft angle
Its being made for Jolene to drag race it. I’ll be fine!
@@tommywilliams5135 I've said the same thing all along for different reasons
Floor looks awesome
Thank you for showing us the process.. it helps me so much while fabricating at work ❤❤❤❤❤
The floor is looking beautiful guys I'm really impressed 👏 👌
Good job, Chad and Jolene!
Best show. I never miss an episode
🤔I think I would screw the top drive shaft panel for easy access & add a driveshaft LOOP for Safety
I watch you every day, love it , I also watch Vice Grip garage, plus DD speed shop ! Love all three !
Said the same thing rooster
Great idea rooster!!!
You think ?
Great idea Rooster!!
Your honestly one of the only channels that actually shares and shows us what to do. I would like to see the last couple cars finished, like the hot wheels car and i definitely wantvto see this done
I didn’t realize that your square tube skeleton wasn’t fully welded to the frame. That it will be cut free from frame and floor will go with the body. It’s not ingenious, simply the RIGHT way to do it !!! Great job Chad 👍🏽
Happy Birthday Doug!!🎉
The floor pans look great!! ✌️❤️
Great job Chad the fluid looks good
Happy birthday, Doug !!
I'm watching the bonus episode with Chad welding to nice music. Iust say that I'm enjoying it so much more than the tutorial and constant cutting and grinding. It's actually relaxing. I'm still watching instead of fast forwarding.😊
Looking good!!!
Great job on floor pan fab and install looks clean
Happy Birthday Doug I hope you have a great day
Looks good all bead rolled out...really coming together...cya tomorrow
Awesome job 🎉🎉❤❤❤
Chad if you clamp a piece of square stock behind those panels you could just push it up tight weld it then take out the square stock
Floor panels look great😊 nice work!
I like ur simplicity and efficiency good sir.
If Chad did it like everyone else you could watch everyone else.... I like the way Chad does his work..😊
Happy Birthday 🎂 Doug 🥳 No Problem for a man of your caliber Chad Go for it Team Hiltz 👁 🐅 👌
HAPPY BORNTDAY DOUGLES!!!!
Eyeballing cuts is one of my favorite activities to do. I’m a tinner by trade but not hvac. Architectural sheet metal copper roofs and such. Dabbled in bodywork for a short while and enjoyed the shit out of. Would love to get back into it slowly building up my tool supply so when I do work on my truck I can go full send. Like how ya work man. Good stuff.
Thanks for everything Chad and Jolene we appreciate the content. The car is looking great so far, that floor is A+
Would the driver line tunnel be strong enough to hold up if the drive line was to break?
Happy birthday Doug !
woww beautiful floor PANEL GREAT JOB
The floor looking good chad
Go for it Team Hiltz
You could sell the grinder sound as a ringtone! Good filming Jolene..
Bad Chad, the fabrication of the square stock and then floor panels is absolutely brilliant. You get a vision in your head and you are able to build what your vision is !! That’s remarkable in my book….🤟🏼✌️😎🥇🥇
i just love watching , maybe 2/3 days behind as i'm D I Y working in my garden .keeping the boss lady happy LOL
Maybe try doing a curved trans tunnel?
Get well soon Fina!
Top work 👏 👌 👍
Chad & Jolene, I hope you enjoy your Saturday evening! Chad I noticed that Rooster said the same thing as I was thinking. Which is that I would screw the top down on the console in case you need to get at the shifter without getting under the car. Also, I have already said that for Jolene's safety you should make a drive shaft hoop! It is easy for you to make in 15-20 minutes and it is made of heavier metal than the floor and it will stop the driveshaft from coming through the floor and hurting someone racing the car! Jolene great work as always, you do such a good job with the camera, the video, and the production of it all!
Yes make a driveshaft loop, sanctioned tracks say it is a must with slicks.
@@FrankKunkel The driveshaft loop issue is an important discussion Chad will probably discuss with Nate
Good & tight, looks almost water tight 😊
Great work!
You putting driveshaft loop in for safety?
Looking good - you're getting there day by day for sure.
Another great job Chad keep up the good work 😊
Hello everyone hope you’re all having a great weekend
“There’s worse things going on for people. That’s for sure.” -Bad Chad
Love your stuff man, and your attitude!!
Good job boys!
I cant say I fully understand this concept but I see it as a great learning opportunity and look foward to seeing the progression, rooting for your success.👍👍🇺🇲
Happy birthday GUYS
Happy Birthday to Doug and Nate
I would get that drive line balanced
Looking good!
I'm learning a lot from you Chad and Jolene by that good camera work thanks for doing this for us
Enjoyed this sunday programming over breakfast! Great job chad! Keep on truckin'! Jolene's camera work is impeccable!❤❤ keep up the excellent content! Many blessings!❤❤❤😊
Chad your floor panels look great,like a pro.
Makes total sense why you are building it the way you are, people just love making negative comments. Trying to bring you down is easier than trying to build themselves up.
hi Chad Jolene & Fina Happy Birthday Doug & Nate hope you had a great day 🥳🥳🥳🥳😎
Happy birthday, Dougles!! 😁
Love it! So awesome!!
love this build
It's always interesting to see you do car floors.
Great work guys 😎👍
I recently tried the edge notch on a metal patch panel on my Jeep Cherokee… worked pretty good. Thanks!
Happy Birthday to Doug. The floor looks great.
G'day Bad Chad,
I think this build is really coming together nicely. The only thing that concerns me is the top console panel and the gear leaver. Fixing the panel could cause problems removing the gearbox.
Thanks for sharing the knowledge man ✌️ Peace from Melbourne Australia.
Awesome, Thanks
I think Rooster 🐔 has a good idea about driveshaft tunnel…..👍🇨🇦
Nice work keep up the good videos
Happy Birthday Douglas.
Happy Birthday Doug from one birthday boy to another!
Looks great , keep it up 👍
Drill holes in hockey pucks, make body mounts !!
He uses boat trailer rollers, no drilling required.
ONly problem with this "bad" job is now it can only be painted on one side looks good on TV and here comes the rust
Awesome job!
Bad Chad and there is nothing wrong with that. Working hard!