Home made sheet metal brake (sheet metal bender)

แชร์
ฝัง
  • เผยแพร่เมื่อ 29 ต.ค. 2024

ความคิดเห็น • 274

  • @TheBlueCollarPreacher
    @TheBlueCollarPreacher  9 ปีที่แล้ว +19

    Angles = 2 @ 50”x 3x3x¼, 2 @ 26”x 1x1x3/16, 2 @ 5”x3x3x¼, 2 @ 6”x2x2x¼.
    Pipes = 4 @ 3”x1”ID (handle inserts), 1 @ 3”x¾”ID, (truss), 2@ 2”x3/4ID (bench clamps),
    2 @ 3”x1/2ID, (hinges), 2 @ 6”x½” round stock (hinges), 1 @ 36” (handle). 5 bolts and nuts 4”x 5/8” 2 springs 1x4, Flat stock 56”x6x½.

    • @FixAllFixer62
      @FixAllFixer62 9 ปีที่แล้ว

      your souther preacher man

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว +2

      donald laisure I'm hick from Wyoming. Preachin in Utah.

    • @FixAllFixer62
      @FixAllFixer62 9 ปีที่แล้ว

      Sweet i love man of GOD that use hands not use there voice

    • @FixAllFixer62
      @FixAllFixer62 9 ปีที่แล้ว

      Looking powder coating stuff

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว

      +donald laisure (73SuperGlide62) Man of all trades, I use my voice as well.

  • @rickhettwer854
    @rickhettwer854 2 ปีที่แล้ว +1

    Great video Preacher, I like your design of this bender, one of the simplest, and yet efficient builds i've seen on Utube. I'm also going to build one in the very near future but i actually am going to make it 5' in length as i need to make running boards, along with other body pieces for my 39 buick coupe project. Thank you for sharing with us.

  • @matt49x
    @matt49x 7 ปีที่แล้ว +12

    that's probably the best one I've seen yet. going on the hunt to find materials to build mine identical to yours. been going through videos trying to find a good and believe this is it.. THANK YOU

  • @shawnellsworth7623
    @shawnellsworth7623 4 ปีที่แล้ว

    Very well built
    Simple yet effective
    The added center down pressure very much needed
    By far the best I’ve seen on here
    Thanks preacher

  • @charlestorruella6140
    @charlestorruella6140 7 ปีที่แล้ว +1

    back in the day you made your tools that you need to make a living and thus guy did a great job on a break it did 14g pretty easy and it looks better then the cheap ones i see at the flea market thanks for the video loved it

  • @PaulDGreen
    @PaulDGreen 5 ปีที่แล้ว +2

    Nice! Best example of what I would need. I was getting worried everyone was making these smaller breaks. I need one 45” so your 50” looks perfect. I’m glad, it looks like it should work!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  5 ปีที่แล้ว

      Yes most sheet metal is 48'' wide so I made sure I could get a piece in it, works great. Thanks for watching

  • @chalemi
    @chalemi 5 ปีที่แล้ว +1

    FINALLY... someone demonstrating the bending of something thicker than sheet metal! Thanks.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  5 ปีที่แล้ว

      THANKS, I get a lot of comments on why I didn't put rods on the lock down bolts so I don't need the wrench, Well the reason is I need more leverage to crank down on this thing to bind heavier gauge material. Thanks for watching.

  • @telberwelding1365
    @telberwelding1365 5 ปีที่แล้ว +1

    Thank you brother I myself is working on a bender and yours give me good ideas may God continue to bless you preaching the word and fabricating metal works

  • @bradpage8967
    @bradpage8967 2 ปีที่แล้ว +1

    The pipe holes in two locations is a great idea! The springs to raise the clamp is a help, maybe need a quicker way of loosening/tightening though.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  2 ปีที่แล้ว

      I don't use this as much as some, it makes it easier for me to store away when I'm not using it. Thanks for watching.

  • @chuckreny2715
    @chuckreny2715 8 ปีที่แล้ว

    There is nothing like American ingenuity. I hope mine comes out as good as this. Well Done.

  • @saneauto
    @saneauto หลายเดือนก่อน +1

    Great job on the build!

  • @tigerseye73
    @tigerseye73 9 ปีที่แล้ว +6

    Very nice job. I have done my share of bending with industrial benders. No matter how heavily built, someone will find a way to bend and distort the bending beams. You may wish to consider adding truss's to the movable angle beam. Angle iron is a good structural unit, but it will distort with enough applied force. Your video is appreciated.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว +2

      +Robert Beck I will most likely only use this bender 2-3 times a year. And nothing more than 16g. anything heavier than that I will buy angle and weld to it. Thanks.

  • @user-ny4ig9qh2e
    @user-ny4ig9qh2e 7 ปีที่แล้ว

    When you aren't preaching you are bending metal. Great Job Preacher, you have built a very nice break and it looks like you have put a lot of thought into it. I like the bull nose edge instead of a sharp edge which can hurt people.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  7 ปีที่แล้ว

      Actually I only use this about twice a year, but I do a lot of other things. Thanks.

  • @ardoinvideos
    @ardoinvideos 8 ปีที่แล้ว

    one of the best basic brakes on the internet! nice Job! Great views of how it was made and used. Props!

  • @austinanson8357
    @austinanson8357 4 ปีที่แล้ว +1

    Going to build one of these on my channel and like you was searching for ideas. Nice job!!!!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  4 ปีที่แล้ว +1

      I say the more the better; that way people can get more ideas. Thanks for watching

    • @austinanson8357
      @austinanson8357 4 ปีที่แล้ว +1

      The Blue Collar Preacher started building mine today, went 80” long with a 75” bend capacity. Yes I agree more is better. I thinking to someday put some pneumatic air rams on mine so I don’t have to manually do it. I’ll give your channel a shout out on my review video of the build. That way some of my followers who don’t know you can check you out!!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  4 ปีที่แล้ว +1

      @@austinanson8357 Looking forward to watching it. I will do the same.

  • @patrickgrow8273
    @patrickgrow8273 7 ปีที่แล้ว +1

    Dear BCP-- FANTASTIC job. You've inspired me to buy a band saw (instead of the brake) and build one myself!

  • @tommy11101
    @tommy11101 7 ปีที่แล้ว

    Good design and video. Like a lot of other people i have wanted to build one of these myself but most videos do not explain there rig . This looks like a very easy break to build and use .Thanks for the material list. I will be on the watch for the teardown video also. Thanks again and keep up the work.

  • @jeffjohnson2792
    @jeffjohnson2792 6 ปีที่แล้ว +1

    Best one I've seen. Great ideas. Love the springs.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  6 ปีที่แล้ว

      Thanks for watching, I also made a nice sandblasting cabinet you might want to check out.

  • @johnjenkins1489
    @johnjenkins1489 7 ปีที่แล้ว

    Great idea to be able to apply some centre force. Much appreciated.

  • @gregfarley5737
    @gregfarley5737 5 ปีที่แล้ว +2

    Very well done!

  • @andrewmarais235
    @andrewmarais235 7 ปีที่แล้ว

    Thank you, a great piece of work you make the world go forward with your publicity.

  • @joelongstaff7601
    @joelongstaff7601 7 ปีที่แล้ว +1

    Preacher I changed up your plans a little.On the ends where you welded the bolts to hold the angle iron die I widened it to hold two bolts so I could move the die back and clamp down some half inch plate so I could use it as a box brake. Cool post thanks for sharing.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  7 ปีที่แล้ว +1

      That is why I love TH-cam, we can learn how to and how not to do things, or even improve on them. Thanks.

  • @garyschriner3926
    @garyschriner3926 8 ปีที่แล้ว +1

    List of material is a big help. We can change or add to based on what you used. Thanks!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  8 ปีที่แล้ว

      +Gary Schriner Thats the good part about TH-cam, get ideas and improve on them.

  • @petertyrrell6690
    @petertyrrell6690 7 ปีที่แล้ว +3

    That looks like a very workable design. Nice work!

  • @joeestes8114
    @joeestes8114 5 ปีที่แล้ว +1

    Very nice! The one i got works great! Thanks for sharing!

  • @ronaldsanchez1341
    @ronaldsanchez1341 7 ปีที่แล้ว

    Humility is this mans virtue; great job!

  • @notwrkn2mch
    @notwrkn2mch 8 ปีที่แล้ว

    Nice..... I saved this one to make in the future. I like the tightening bolt in the center

  • @Rudderify
    @Rudderify 9 ปีที่แล้ว +2

    Thank you for the explanation and the walk-through. Great vid and I have another project to add to the list. 😄

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว

      +Rudderify Thanks. working on oven now. will be posting shortly.

  • @kevinashby3784
    @kevinashby3784 8 ปีที่แล้ว +1

    Very nice. Simple but useful design.

  • @joracer1
    @joracer1 4 ปีที่แล้ว

    Best out of the way brake when not in use I've seen.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  4 ปีที่แล้ว

      Thanks. Yes I have only used it a hand full of times since I made it, but when I need it I can get it out. Thanks for watching.

  • @dionedean7918
    @dionedean7918 8 ปีที่แล้ว +1

    great job guy , loads of info keep up the good work

  • @lloydcisco3027
    @lloydcisco3027 7 ปีที่แล้ว

    Great idea on the truss to keep the angle. From bowing nice build

  • @thefeedwelder9083
    @thefeedwelder9083 6 ปีที่แล้ว +1

    To make bend less muscle put a diagonal pipe on the ends and put a counter weight at the bottom. Do not try to make the bemd all at once, but do the bend 3 to 4 smaller bends. Now I got to build one for my shop, great job !

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  6 ปีที่แล้ว

      Thanks for watching, I only use my bender about once a year, and need to store when not in use.

    • @thefeedwelder9083
      @thefeedwelder9083 6 ปีที่แล้ว +1

      I will be building mine in the next week to build stainless tool boxes. Trying to come up with a way to add fingers.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  6 ปีที่แล้ว

      Cool, I just subscribed to your channel can't wait to see some stuff welded up.

    • @thefeedwelder9083
      @thefeedwelder9083 6 ปีที่แล้ว

      Just opening up my channel, just got electric in my 2 car metal garage so I'm off and running. First project is getting my garage organized ( been the families storage for the last 2 years) and fix my trailer so I can haul some metal. This week I have some long restaurant stainless serving tables coming in which will become tool boxes. For that I got to make a break for the stainless. I think If I just a couple short 1/2 "plate, and put a shim between them on the ends. Bevel the top edge, I can use that for the short bends instead of needing to use fingers.

  • @camilohernandez2202
    @camilohernandez2202 5 ปีที่แล้ว +1

    That is a awesome ! Video . I liked what you said , giving the credit to the instructors you had in the past . well I want to thank you for sharing your idead . If God's will I'll buildone my self see how it'll come out . God bless you!

  • @samuelclark4525
    @samuelclark4525 6 ปีที่แล้ว +1

    Thanks for the video. I need to weld up one of these for myself with my powerimig.

  • @orlandocardosa2306
    @orlandocardosa2306 8 ปีที่แล้ว

    Gracias Sr Termine de fabricar mi Dobladora Guiándome de su Tutorial Saludos Cordiales des Perú.

  • @getoutofCanadaB4its2late
    @getoutofCanadaB4its2late 9 ปีที่แล้ว

    Weld a couple bars on opposite sides of the nut so you don't have to fumble around with a wrench. Or weld one of those Chinese wrenches to the nut! Great build. Thanks for posting!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว

      +Mark W I use this thing maybe once a year. If I had to use it more often that might be a good idea.

  • @ryansherwood7351
    @ryansherwood7351 7 ปีที่แล้ว

    You should weld some levers onto the bolts to speed up tightening/loosening. Good job ... going to steal your idea. Thanks!

  • @3dsingh992
    @3dsingh992 8 ปีที่แล้ว

    love all the details!

  • @boatanchors6652
    @boatanchors6652 6 ปีที่แล้ว

    Great Job Blue Collar Preacher.. Thanks so much for doing the video and all the tips, I to have been wanting to make a break and have watched a lot of the other TH-cam video's on DIY breaks.. Great Job..

  • @amscout1156
    @amscout1156 6 ปีที่แล้ว

    That is a very clean design and well made project. I want to use my everlast and weld up a sheet brake. I hope it turns out as nice as yours did.

  • @georgespangler1517
    @georgespangler1517 2 ปีที่แล้ว

    Well made same design as mine I've had for 20 years l made 3 different size pipe diameter top jigs for radious bends

  • @lloydcisco3027
    @lloydcisco3027 7 ปีที่แล้ว

    I was going to make a stationary truss you have the idea glad I watched your vid

  • @carpenter7072
    @carpenter7072 6 ปีที่แล้ว

    I do like it and thanks for shared. I'll build my I need it for my food cart project.

  • @danradusinovich332
    @danradusinovich332 7 ปีที่แล้ว

    Thank you for the video, I will be working on mine this weekend

  • @garygerard4290
    @garygerard4290 4 ปีที่แล้ว +1

    nice build

  • @hootinouts
    @hootinouts 7 ปีที่แล้ว +1

    Nice job preacher! I built one from scratch as well but mine can't handle anything thicker than 26 gauge steel sheet like they use in HVAC duct work. I was going to add a truss but put it off until I tested it out. If I try to bend 14 gauge, I get bowing in the clamp. After looking at your fine job, I'm going to add the top truss to mine. God willing, I'd like to post mine once I get it refined. for clamping the stock down, I have an eccentric cam mechanism that draws the top clamp down using a single lever.

  • @robegerton2497
    @robegerton2497 9 ปีที่แล้ว +1

    Very nice!! thanks for sharing and some good idea's

  • @omarfarsha5886
    @omarfarsha5886 4 ปีที่แล้ว

    Wow that is really nice. That is something I want to make with my everlast welder when I've got a bit more space.

  • @jthode1
    @jthode1 7 ปีที่แล้ว

    Nice looking break! Unless you are counting on the strength and stiffness of the table it is mounted on, it looks like the bottom 1/2" x 6" base could use a truss or vertical plate stiffener. The 1/2" x 6" steel base is quite flexible in the vertical direction and this would not allow the material to be clamped in well.

  • @michaelstreete26
    @michaelstreete26 9 ปีที่แล้ว +1

    Out of all the metal breaks I've seen on TH-cam, yours the best. If you don't mind can you share your plans? The materials, measurements, etc.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว

      Michael streete I will get those soon thanks.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว +1

      Michael streete Angles = 2 @ 50”x 3x3x¼, 2 @ 26”x 1x1x3/16, 2 @ 5”x3x3x¼, 2 @ 6”x2x2x¼.
      Pipes = 4 @ 3”x1”ID (handle inserts), 1 @ 3”x¾”ID, (truss), 2@ 2”x3/4ID (bench clamps),
      2 @ 3”x1/2ID, (hinges), 2 @ 6”x½” round stock (hinges), 1 @ 36” (handle). 5 bolts and nuts 4”x 5/8” 2 springs 1x4, Flat stock 56”x6x½.

  • @Max_R_MaMint
    @Max_R_MaMint 6 ปีที่แล้ว

    Weld the hold down nuts to the end of a 3" or 4" long piece of 3/4" or 1" pipe, weld a cross handle on the other end of the pipe - no more finding wrenches! For the truss adjustment, a 4" or 5" stick of steel welded to the flat of the adjustment nut.

  • @toddweller
    @toddweller 7 ปีที่แล้ว +2

    Excellent job! Well done!

  • @watahyahknow
    @watahyahknow 8 ปีที่แล้ว

    i think if you cut vertical slits in the front half of the clamp part with a thin disk on an angle grinder at uneven intervals you can actually use those when youre bending a (1 inch high) box from sheetmetal , the sides allready bend need to fall in the slots when you bend the next then you can bend beyond the angle of the clamp itself

  • @garryfisher5512
    @garryfisher5512 7 ปีที่แล้ว

    Looks great.

  • @inthelandofmilkandhoney457
    @inthelandofmilkandhoney457 8 ปีที่แล้ว

    Nice Job...Looks good too....

  • @luckydubeinrc5165
    @luckydubeinrc5165 8 ปีที่แล้ว

    Good job, now add some roundbar handles on the nuts, so u won't need the wrench to tighten,150mm x 10mm bend at 50mm 45 degrees, to form a handle , weld to nut's. the centre nut add a T handle, 2 100mm pieces off roundbar welded to nuts, round the ends off so as not to hurt your hands.
    We are not old just have some miles on us :)

  • @rooikatza
    @rooikatza 6 ปีที่แล้ว

    I defnitly will thanks for the wonderfull tips

  • @thorthunder3227
    @thorthunder3227 5 ปีที่แล้ว +1

    Real nice unit.

  • @MrHappycyber
    @MrHappycyber 8 ปีที่แล้ว

    I would like to do this bending but in a smaller scale, to a feeder that stores about 22 pounds of food to feed stray dogs. Thank you for your idea Greetings from Venezuela. Excuse my English

  • @electricos3
    @electricos3 9 ปีที่แล้ว +3

    muy buen video gracias por subirlo

  • @RosaStringWorks
    @RosaStringWorks 7 ปีที่แล้ว

    nice job.

  • @irgski
    @irgski 6 ปีที่แล้ว

    nice job! Looks like it has the best of all features for a brake.
    One suggestion - I think it would be better if you can fold the edge a little past 90degrees due to metal property’s when bending...you may want to go to 45degrees in order to do a hem edge.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  6 ปีที่แล้ว

      Thanks I just use a ball pein hammer and tap it down to the edge of the angle iron, then re clamp it down in the brake to flatten it down, when I get my new shop up and running I will have to demonstrate.

    • @irgski
      @irgski 6 ปีที่แล้ว

      The Blue Collar Preacher Great! Can’t wait to see it.

  • @alzathoth
    @alzathoth 8 ปีที่แล้ว +1

    it would be cool if you could add 'fingers' to the brake for box/pan bends. also if you welded a few pieces of rod to your bolts, you wouldn't need a wrench to insert/remove pieces from the brake. :)

  • @louiemalaon1833
    @louiemalaon1833 9 ปีที่แล้ว +2

    thank you for the idea sir... i hope u do a lot more videos

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว +1

      +louie malaon I have added a few more since this one. Thanks.

  • @jamesdickson3616
    @jamesdickson3616 5 ปีที่แล้ว

    Good job mate come in handy for you .old jimmy west australia

  • @73turbos
    @73turbos 7 ปีที่แล้ว

    Great job!

  • @JaiUneGuruDeja
    @JaiUneGuruDeja 7 ปีที่แล้ว +1

    You dah man! Gotta learn to weld so that I can be all-powerful like you.

  • @tubester4567
    @tubester4567 8 ปีที่แล้ว +2

    One of the better home made benders. You could make handles for the adjusting nuts so you dont have to rely on a shifter. Also, the centre truss bolt should not need to be tightened for every job, once its adjusted, it should not need to be moved. I can see a small problem thats causing your bends to be not very sharp. You have a gap and too much space between the top blade and the bottom one. Otherwise it looks ok.

  • @alexiicon
    @alexiicon 8 ปีที่แล้ว

    Good solution!

  • @dibrardodorarbid
    @dibrardodorarbid 7 ปีที่แล้ว

    Good job 👍

  • @Redpitdog
    @Redpitdog 7 ปีที่แล้ว

    very nice thank you for posting !

  • @harbhajankhalsa
    @harbhajankhalsa 8 ปีที่แล้ว

    Great video! Thank you

  • @e210dall3
    @e210dall3 7 ปีที่แล้ว +1

    Thanks buddy. Just copied part of your design. Turned out sweet. I now have a Lean Green Bending Machine

  • @rexwilson6598
    @rexwilson6598 7 ปีที่แล้ว +1

    Great Job Preacher looks and works great !

  • @walkertongdee
    @walkertongdee 9 ปีที่แล้ว +2

    I have thought about making one but figured it would take up too much space in the shop but looking at yours I see it can be easily stored in the corner on the floor next to a wall..

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว

      +Walkertongdee Yes I actually store mine on the bottom shelf of my work table that I made out of an old door (the one in the video).

  • @chuymartinez5942
    @chuymartinez5942 8 ปีที่แล้ว

    EXCELENTE VIDEO!!! GRACIAS POR COMPARTIR

    • @robertocelular7420
      @robertocelular7420 8 ปีที่แล้ว

      como sereparrau con geladrco matraca. sankey

  • @RickRose
    @RickRose 8 ปีที่แล้ว

    Well done--thanks for sharing.

  • @surasitchitchumnong5762
    @surasitchitchumnong5762 7 ปีที่แล้ว

    very good

  • @maikelpereiraferreira2833
    @maikelpereiraferreira2833 8 ปีที่แล้ว +1

    finily I've got what I needed, thanks fellow you very smart, I'll bild one just coples inchs bigger then yours for gotters y know

  • @jorgecabrera2589
    @jorgecabrera2589 8 ปีที่แล้ว

    Good video I like

  • @sergioolivares4593
    @sergioolivares4593 3 ปีที่แล้ว

    Cuanto mide de largo excelente maquina

  • @23adammrmr
    @23adammrmr 6 ปีที่แล้ว +1

    This is the way better benders I seen on TH-cam great job can you tell me the dimensions of the angle iron that you have used to make this Bender

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  6 ปีที่แล้ว +1

      I pined all the dimensions and material needed, should show up at the top of the comments. Thanks for watching.

    • @23adammrmr
      @23adammrmr 6 ปีที่แล้ว

      @@TheBlueCollarPreacher thank you sir have a bless day be well be blessed

  • @AntonioHernandez-pc1iq
    @AntonioHernandez-pc1iq 8 ปีที่แล้ว

    nice machine

  • @keithkrueger1609
    @keithkrueger1609 9 ปีที่แล้ว +1

    nice job

  • @walkertongdee
    @walkertongdee 9 ปีที่แล้ว

    Cool, I used to set up them in a factory, always wondered why they call them a brake when they bend not break, if they broke the metal that wouldn't be good......

  • @gasparoochie
    @gasparoochie 4 ปีที่แล้ว

    I liked your Sheet Metal Brake so much that I'm in the process of making one. Any chance of being able to see some pictures of the section where you have welded the bolt to the truss at the top as I'm a bit unsure how you have put it in place there. Thanks

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  4 ปีที่แล้ว

      I used a 6" 5/8" bolt cut the head off, and welded the truss section to it, and welded a 3/4" pipe at the top of the angle at the bottom (Be sure you thread your nut on first, when you tighten down on the nut it pushes the truss against the angle forcing it down. Hope this helps, I have super busy lately doing like 4 jobs a week at this time, also we relocated to Wyoming from Utah about 2 years ago, and still have most the shop packed up; We are in the process of building new house and shop. Thanks for watching.

  • @derek876544
    @derek876544 7 ปีที่แล้ว

    smart job

  • @amtpdb1
    @amtpdb1 3 ปีที่แล้ว +1

    Can you change the bend radius on this? If you can, how would or do you do it? Thanks

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  3 ปีที่แล้ว +1

      I'm not sure what mean by radius? if you are talking about the angle degrees, it can only go slightly less than 45 degrees. If you are talking about the radius of the bend itself, I've used pipes clamped down to it and used hammers to bend it. I think my truck floor board video shows how I did that. Thanks for watching.

    • @amtpdb1
      @amtpdb1 3 ปีที่แล้ว

      @@TheBlueCollarPreacher
      Thanks for the information. Stay well

  • @devinhaury4912
    @devinhaury4912 8 ปีที่แล้ว

    Hey that's a good idea thanks for sharing this, but I wanted to give you an idea put crank wheels at the end and middle so you don't have to keep dropping that damn crescent wrench lol good luck bro

  • @kessgr
    @kessgr 9 ปีที่แล้ว +3

    Good job, and thanks alot for your credits to me and the other people, you are very kind.
    To solve the stuck problem when releasing the brake, you must turning the locking bolts up side down . Your brake, find it difficult to slide over the threads of the bolts so stuck.
    Also your hinges, the internal diameter of bushing is too big for this pivot (as I can see, on video, the gap must be at least about 2.5 mm).
    Good luck at your next projects.
    Bill

  • @scottsawyer2222
    @scottsawyer2222 8 ปีที่แล้ว

    Gosh I looked everywhere here can" find anything but one that is 3.5". Couldn't find that size on line either. Another question, started welding the pieces today, for the hinges, the solid tube pieces, did you weld them to the inside of the angle iron? The picture almost looks like maybe you removed some material to fit the piece in?Thanks again!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  8 ปีที่แล้ว

      +Scott Sawyer I used regular 3/8 black plumbing pipe for that, and 3/8 round stock.

  • @imysteryman
    @imysteryman 7 ปีที่แล้ว

    The edge of the top clamp should be set back 1.5 times the thickness of the metal. I have scene several commercial benders messed up because the operator did not set the top back far enough.

  • @Lonewolf3165
    @Lonewolf3165 9 ปีที่แล้ว +1

    Real nice job, both on the brake & the video! Nice & clear so we could see what you did. Some of the other guy's aren't so clear.What did you use to weld it together? MIG or stick?Thank you!

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว +1

      +Lonewolf3165 I have a mig 220V 40amp. took a while for me to dail it in, but I think I am better welder now.

  • @benking4292
    @benking4292 8 ปีที่แล้ว

    I'm impressed, what's the max Gage thickness you can bend? and to do away with the "Bull Nose " have you given thought to perhaps putting a bevel on the forward or leading edge of the pinch/bridge bar ?

  • @brotherricksafety
    @brotherricksafety 9 ปีที่แล้ว

    i like that

  • @DDEENY
    @DDEENY 9 ปีที่แล้ว

    All of the TH-cam homemade brake videos that I've seen show the operator's need to continually loosen, then tighten the lock-down nuts at each end (and in this case, the center). It seems to be more time-consuming than desirable. I'm thinking cam levers with handles that are quicker and more user-friendly.

    • @TheBlueCollarPreacher
      @TheBlueCollarPreacher  9 ปีที่แล้ว

      DDEENY If you need to use it like on a daily basis, you might just invest in one. I only use mine on occasions, like once or twice a year.

  • @baronbaronov760
    @baronbaronov760 8 ปีที่แล้ว

    thanks for the video .you could further explain how the bolt is tightened average?

  • @jiml9944
    @jiml9944 7 ปีที่แล้ว

    The hinge has me baffled. Can't see how the 5/8 axle is attached to the angle iron. The pipe appears continuous.
    What man I missing ? I'm finishing one that uses 3 part hinges, which is difficult to align. Thanks !

  • @521farmer
    @521farmer 7 ปีที่แล้ว +1

    Say what they want ya did Fine Job Goin to Build Mine Like Your,s just goin to change the color to Yellow Thks again Preacher