The brushed ESC can be Lipo compatible I think you’ll need to move them little pegs around on the ESC , This was the Quantum plus . So it is brushless and Lipo ready. Also I changed the pinion gear to a 17 tooth Made it a 50mph truck . On 3s
Hi. Is there any way to factory reset this ESC? I changed something during this programming and I would like to return to the factory settings. thanks and regards.
Hello, that is a good question to which I am not sure I personally do not think so, However I have a link to the Manual if you haven’t got it ? You could try to ring HPI , I’ve generally found them quite helpful in the past. But here is the link to the manual. You want page 10. www.hpiracing.com/assets/documents/maverick/instructions/150244_006_vol01_flx10_3s100_brushless_esc_10112020.pdf
Yes it is sold as being brushless , I’d recommend thicker oil in centre differential , and about a 17t pinion gesr seems to bring into where you’d expect it to be . As it has plenty of torque but Low RPm motor , so higher tooth pinion gear gives it some legs .
@@oldskoolrolla Cool I’d advise putting a washer same inner dia as the axles and an Outter dia close size to the 17mm hex this will help take some pressure from the axle as there’s a small gap between the hub and the 17mm hex . So Eg: if you spin out and bumped the rear wheel into a curb there’s a chance it could bend the axle slightly , if you pad out the gap with washers/shims that is less likely to happen . And the motor can run 17 tooth pinion on road and get around 50mph on 3s mine topped 49moh on 3s with 17tooth pinion and cheap Youmme Lipo .
@@sheldonrose461 Very Strange, I have no Answer other than get into contact with Hpiracing.com tell them the problems your having with your esc. Just clarify it is the 100amp ESC and it’s the Quantum PLUS . ? Reason I’m asking is that the Smaller Maverick MSC BL30WP ESC only goes up to Level 4 on the punch setting .
THANKS SO MUCH for the tips I Never knew you cld set it directly on the car itself but only with an ennoying programing card.. THANKS so much Bro' You're the best
@@mark-1rc502 ya it does, haven't checked my MT flux yet but I will, definitely.. I used to be frustrated not finding the right programing card that I got fed up' 😂 Your video always make me wanna bring my rc's out anyway.. Cheers mate'
Argh I did think of that but I recorded this on my mobile briefly . It is available on Maverick website . I shall download it my self and remake the video and include the chart for All to see .
Wow, that's a very helpful video.
Thanks for sharing :)
So 10 (two long beeps) is for max punch? and we need to set value from 1 do 5? do you have any instrukcions for meanings from 1 to 9 beeps?
Brilliant video mate thanks for the help 👍
I hope it done your job, not the best vid but didn’t have a lot of time 🤗
thank you for this video, it helped me a lot 😁
I’m pleased it has helped some people .
Thank you .
Hi mate, just got one of these trucks,,can i wack a lipo on it ,,and upgrade the pinion by any chance,,? Thanks mate ?
The brushed ESC can be Lipo compatible
I think you’ll need to move them little pegs around on the ESC ,
This was the Quantum plus .
So it is brushless and Lipo ready.
Also I changed the pinion gear to a 17 tooth
Made it a 50mph truck . On 3s
Hi. Is there any way to factory reset this ESC? I changed something during this programming and I would like to return to the factory settings. thanks and regards.
Hello, that is a good question to which I am not sure I personally do not think so,
However I have a link to the Manual if you haven’t got it ?
You could try to ring HPI , I’ve generally found them quite helpful in the past.
But here is the link to the manual. You want page 10.
www.hpiracing.com/assets/documents/maverick/instructions/150244_006_vol01_flx10_3s100_brushless_esc_10112020.pdf
Es el mismo programa para el esc flx 80amp?
How did u find out what the programs settings are. 😁
www.hpiracing.com/assets/documents/maverick/instructions/150244_006_vol01_flx10_3s100_brushless_esc_10112020.pdf
is this brushless ?thanks
Yes it is sold as being brushless ,
I’d recommend thicker oil in centre differential , and about a 17t pinion gesr seems to bring into where you’d expect it to be . As it has plenty of torque but Low RPm motor , so higher tooth pinion gear gives it some legs .
very nice 👍😍👍 🎵
Hope it was of help brother 👍
Nice one bruv 👍👊😎
Geeeeezzzzzaaaaa .
Niiiiiicccccccceeeee one !
Get in there 😂👍👍
Thanks mate 👍
Your welcome brother glad it was of help to you .
P.S. Thanks For subscribing very much Appreciated
@@mark-1rc502 no problems. Just ordered one of these Quantum plus models so hopefully it will be good!
@@oldskoolrolla
Cool I’d advise putting a washer same inner dia as the axles and an Outter dia close size to the 17mm hex this will help take some pressure from the axle as there’s a small gap between the hub and the 17mm hex .
So Eg: if you spin out and bumped the rear wheel into a curb there’s a chance it could bend the axle slightly , if you pad out the gap with washers/shims that is less likely to happen .
And the motor can run 17 tooth pinion on road and get around 50mph on 3s mine topped 49moh on 3s with 17tooth pinion and cheap Youmme Lipo .
@@mark-1rc502 sweet thanks so much for your advise. I will do that. With the 17 tooth does it still have plenty of punch for wheelies and backflips?
Hi what is the pitch gearing on this please
Pretty sure it’s Mod.1
Do you know why mine only has four modes, no long beep
It must do brother . What did you want to change
@@mark-1rc502 well I was just testing out some settings, and noticed the modes just went to 4 and punch mode only went to L4
@@sheldonrose461
Very Strange, I have no Answer other than get into contact with Hpiracing.com tell them the problems your having with your esc.
Just clarify it is the 100amp ESC and it’s the Quantum PLUS . ?
Reason I’m asking is that the Smaller Maverick MSC BL30WP ESC only goes up to Level 4 on the punch setting .
Do you know where to get the setting chart
Yes mate
www.hpiracing.com/assets/documents/maverick/instructions/150244_006_vol01_flx10_3s100_brushless_esc_10112020.pdf
@@mark-1rc502 thanks mate you have helped loads
All I need now is a wheelie bar
@@chrisj3741
Take this From EBay.
Worth it considering wheelie bar £6.99 plus p&p
254811352466
Thanks mate I might go for that 👍
buen videoo!! 😎😎😎+1
☝️👍👍👍👍👍
Just a little video to show how to program the ESC .🙏☺️
THANKS SO MUCH for the tips
I Never knew you cld set it directly on the car itself but only with an ennoying programing card..
THANKS so much Bro'
You're the best
Again I thank you Sir 🫡
I appreciate your feedback good or bad it all helps 🤗 I’m happy that this video has helped you .
@@mark-1rc502 ya it does, haven't checked my MT flux yet but I will, definitely..
I used to be frustrated not finding the right programing card that I got fed up' 😂
Your video always make me wanna bring my rc's out anyway.. Cheers mate'
Any one got a chart ?
Argh I did think of that but I recorded this on my mobile briefly .
It is available on Maverick website .
I shall download it my self and remake the video and include the chart for All to see .
I found a better way to get max punch. I bought a Kraton 6S.
I added more punch to my Kraton with a Max 8 combo