There is a one problem 😉 you can't of the light from another switch 😉 it's mean if you get one the light from a switch . you can't get off from another switch
No matter how many switches you use, only the two switches at both ends can be " 2-way switches". All the middle ones must be " 3-way switches ". Then you can turn on the lamp from any switch and turn it off from any other switch randomly and vise versa. There is a simple logic of the function of a " 3-way switch " which is to reverse the two input wires signal to the two output wires from 0 to 1 and from 1 to 0 correspondingly. Therefore the logic of any one of the segment pair of the middle two wires are either in a (0,1) or a (1,0) status. This guarantees the on going lines always have one and only one with line voltage while another line always has 0 volt dynamically. ( FYI : In North America, they call the 2-way switch in Europe as " 3-way " while the 3-way switch in Europe as "4-way ". Make sure to get the correct switches in your country. )
Logically there must be some fallacy in the wiring shown. When two adjacent input switches are in the same state, bulb will always glow no matter the position of the third switch connected to output.
У Европи , за ово постоји много једноставније , сигурније решење . И то бесконачно за укључивање . Овај млади момак је паметан , али не мора да измишља " топлу воду " . Неко је то већ одавно решио , много боље .
This is really an interesting thing. It needs today. I remember while climbing to first floor our place was climb up 4 or 5 steps turn left the the corner angular stairs then a 5 feet square landing then climb up again a long flat area climb up next then climb up fully to first floor. Now at bottom square the wall facing up a tube light. There is a switch also. At the bottom on your also there is a switch. Now our boss said the bottom switch and the first 5 feet square landing should be connected that we switch on and off at both levels. If we forget to switch off we switch off from the bottom. While climbing if we need light we switch on at the landing. But the safely is if we switch off at the entrance this switch doesn't work.
No. This is for amateur technicians. You need two SPDT switches(3 terminals) and one DPDT switch(6 terminals, connected crossover) for a single load to be operated independent of the other two switch positions. Truth table valid and ON/OFF possible from any switches.
Bhai connection thik hai switch ka par blu wire switch me bulp ka read wire lagega aur bich ka switch me khali hai usme men phase lagega niutal direct jaiga
Dependendo da posição das 3 teclas , será necessário apertar mais de uma tecla para desligar ou acender a lâmpadas. O objetivo deste circuito seria não se deslocar de um ambiente da casa para outro para acender ou apagar uma lâmpada , porem, neste projeto será necessário.
Sem contar que os interruptores são paralelos. Não há necessidade nenhuma de cruzar fios dos circuitos. Dá no mesmo e não confundiria. É só pra parecer mais complexo.
its not applicable for stair case ,no option for one switch on and off from another one .for that system you want to use a intermediate switch in between two 2 way switches,then it will be any switch on and from any switch off.
mr. Asokan, i was trying to control one light bulb from three switches. two switches are on either side of our bed and one is on the board near the door. can you send a diagram incorporating your suggestion which appears feasible.
It can be done using a contractor having one NO and one NC contacts (230v coil supply) . If using this way, the wiring become more neat and beautiful. If we use an intermediate switch,it be different look than other two. If follows the circuit in the video it will not give indipendent control.
In hotels once you enter you switch on the bed room control switch. Later alternative switches. But either side switched are independent. But the same bulbs have independent control at the opposite mirror side. Suppose you get you can still switch on the bulb at the dressing mirror area. Next thing is regulated lighting. The passage light blow could be reduced by regulator, and it helps to increase when needed at night again reduced to low light then in the morning you are either switch off by regulator or by switch. Today many many inventions has come.
Eso no funciona como debería, si te das cuenta. El interruptor que recibe la corriente siempre debe estar en una posición específica para que los otros 2 funcionen. Si el primer interruptor cambia de posición, los otros 2 dejarían de funcionar
هناك ادوات كتيرة موجودة وسهلة ولا تتطلب تعقيدات مثل cruze y conmutador suficiente para hacer cualquiera aparte los telereptores y ascensores del movimiento y muchas cosas
Eu não achei correto: em um corredor longo o certo é colocar interrupitor paralelo em cada ponta e varios interrupitor inverssor de faze sendo um em cada porta exemplo corredor de apartamentos
lakin apne yeh nai bataya k konsi wire apne kiske saath Q jori .. why cross wiring .. I click on your video but stopped watching because you didn't explain what are you doing and why are you doing? next time when you upload video do please answer WHY?
Basta mettere tutti gli gli invertitori che vuoi al centro dei due deviatori è accendi e spegni da tutte le posizioni che vuoi. Altrimenti con un relè passo passo e dei semplici pulsanti con due fili accendi e spegni tutto quello che vuoi
El circuito no sirve. Siguiendo la línea de corriente, el primer y segundo interruptor siempre tendrían que estar apuntando a la misma línea de cable, si el primer y segundo interruptor apuntan hacia arriba, el foco nunca se apagará. Así de simple. Pará ese tipo de circuitos se fabrico el interruptor de 4 vías, ya que es la única solución para que el circuito funcione con 3 o más interruptores.
Guru ji ko koi batye ki 1 se on to 2 se off hota hai, paglu ekhi switch se on off kar raha hai, pol tab khule jab sahi se bataye do switch ek jaise hi joda hai
یہ صرف 2 وے سوئچ ٹھیک کام کرتا ہے ۔۔۔۔ یعنی آپ نمبر 1 سوئچ کے ذریعے اگر بلب آن کرتے ہیں تو نمبر 2 سوئچ سے آف کر سکتے ہیں اسی طرح اگر نمبر 2 سوئچ سے آن کیا ہے تو نمبر 1 سوئچ سے آف ہو سکتا ہے ۔۔۔۔۔ لیکن اس میں یہ ہے کہ جس سوئچ نمبر سے کیا اسی سے آف کرنا پڑے گا
This is wrong Bulb ko aik switch sey on karo aur doosrey switch sey off karo phir pata chaley ga Is main aik switch Intermidiat use ho ga phir sai kaam ho ga
There is a one problem 😉 you can't of the light from another switch 😉 it's mean if you get one the light from a switch . you can't get off from another switch
you are right
دارة خاطءة..تمعن في المفتاح 1انه لا يتحكم
Indeed! He did not show changing two switches.
At the end of video yes the right switch cant turn off the light 😂
111
110
100
101
011
010
001
000
Kon kon 2024 me dhekh raha hai
Hmm dekh rhe h 😂😂😂
भार्या, बहुत आसान तरीके समझाया है। थन्यावाद जी ।😂
এই সারা পাগল
साइड साइड के दोनों स्विच को ऑन पोजीशन पर रखो और बीच वाले स्विच से लाइट ऑफ करो ऑफ नहीं होगा
Bahot Bahot Dhnya Vaad Maine Waise Jankari Magithi Par Kisine Mujhe Bataya Nahi Waise Esi Hai Par Jankari Hona Jaruri Hai Thanks
Ye to thik hai par ek jagah se on karo or dusri jagah se off karne se nahi hoga jo
Right
Its not three way connection😇 its just a simple one way connection and bulb 💡 glow with three switches from three different locations
Jhantu blam mla kro mind less 😁😜😁😜😁😜😜😁😁😜
ஒரு சுச்சில் ஆண் செய்து இன்னொரு சுச்சில் ஆப் செய்ய வேண்டும் அப்போது தானே சாதநை ஆகும்.
முயற்சிக்கு வாழ்த்துக்கள்.
நன்றி
merci pour cet ajout très simple.🎉🎉❤
Aduri jaankari hai apki
No matter how many switches you use, only the two switches at both ends can be " 2-way switches".
All the middle ones must be " 3-way switches ". Then you can turn on the lamp from any switch and turn it off from any other switch randomly and vise versa.
There is a simple logic of the function of a " 3-way switch " which is to reverse the two input wires signal to the two output wires from 0 to 1 and from 1 to 0 correspondingly. Therefore the logic of any one of the segment pair of the middle two wires are either in a (0,1) or a (1,0) status. This guarantees the on going lines always have one and only one with line voltage while another line always has 0 volt dynamically.
( FYI : In North America, they call the 2-way switch in Europe as " 3-way " while the 3-way switch in Europe as "4-way ".
Make sure to get the correct switches in your country. )
Logically there must be some fallacy in the wiring shown. When two adjacent input switches are in the same state, bulb will always glow no matter the position of the third switch connected to output.
@Vikas Kumar
Using 2-way switches can only have a maximum of two INDEPENDENT switches control. Other than that, we need to introduce 3-way switches.
The fallacy is shown at the end.
3 way or intermediate switches
Right. This is literally not perfect. You need an intermediate switch probably . So do not bother about any Tension.Thanks .
Line conection kaha se kiya mere bhai adhura hai vdo🤗🤗😝😝😝🙏🙏🙏
У Европи , за ово постоји много једноставније , сигурније решење . И то бесконачно за укључивање . Овај млади момак је паметан , али не мора да измишља " топлу воду " . Неко је то већ одавно решио , много боље .
Water moter ko is tarah connect kar sakte hain kya?
Yes
This is really an interesting thing. It needs today. I remember while climbing to first floor our place was climb up 4 or 5 steps turn left the the corner angular stairs then a 5 feet square landing then climb up again a long flat area climb up next then climb up fully to first floor.
Now at bottom square the wall facing up a tube light. There is a switch also. At the bottom on your also there is a switch. Now our boss said the bottom switch and the first 5 feet square landing should be connected that we switch on and off at both levels. If we forget to switch off we switch off from the bottom. While climbing if we need light we switch on at the landing. But the safely is if we switch off at the entrance this switch doesn't work.
You can what? 🤦🏻♂️
Dear friend. Selam From Türkiye. İt is very fine proje. Thanks very much.
No. This is for amateur technicians. You need two SPDT switches(3 terminals) and one DPDT switch(6 terminals, connected crossover) for a single load to be operated independent of the other two switch positions. Truth table valid and ON/OFF possible from any switches.
Hlw ist switch on rkho
Aur 2nd switch off kro fr pta laga thk hai ki nhi 😂😂😂
1ကိုင်း3ဝေးဆိုရင်ဟိုဘက်ဒီဘက်ကစားပြရမှာခလုတ်တစ်ခုတည်းကိုဖွင့်လိုက်ပိတ်လိုက်..နောက်တစ်ခုကိုဖွင့်လိုက်လုပ်လို့မရပါဘူး😅
Last walay Ulta. On off wallay switch ko outer wires ko replace. KR dain to 3rd wala switch bhi theek on off kre ga plz
Thanks nice tutorial Vedio❤️🙃
Bhai connection thik hai switch ka par blu wire switch me bulp ka read wire lagega aur bich ka switch me khali hai usme men phase lagega niutal direct jaiga
😅😅😅😅😅😅😅😅😅😅😅
बोर्ड में line का connection तो दिखाया ही नही है। बिना supply के bulb कैसे on हो रहे हैं?
Arhe Bhai line connection Diya aap samaj nahi pa rahe ho
Sahi bat he
o
In lhdb
Ue AA awà
बल्बवाली न्यूट्रल और निलेमे रेड पाँझीटीव कनेक्शनदी
भाई पहले टेस्टर पकडना सीखो 😅😅😂
Sir ap kitni bar yesi viedeo dalenge?
2nd wala suich koi kamka nahi ❌.iski jaga 4 pin wala suich lagaiye Jo × = connection hota hai.✅
Is tarh to one way switch se bhi on off ho jayega 😅😅😅
3 button ulta kaam kyo kar Raha hai kya ise sidha nahi laga sakte hai
Dependendo da posição das 3 teclas , será necessário apertar mais de uma tecla para desligar ou acender a lâmpadas. O objetivo deste circuito seria não se deslocar de um ambiente da casa para outro para acender ou apagar uma lâmpada , porem, neste projeto será necessário.
pois é, foi o que percebi
8iiihighiiii
Sem contar que os interruptores são paralelos. Não há necessidade nenhuma de cruzar fios dos circuitos. Dá no mesmo e não confundiria. É só pra parecer mais complexo.
its not applicable for stair case ,no option for one switch on and off from another one .for that system you want to use a intermediate switch in between two 2 way switches,then it will be any switch on and from any switch off.
mr. Asokan, i was trying to control one light bulb from three switches. two switches are on either side of our bed and one is on the board near the door. can you send a diagram incorporating your suggestion which appears feasible.
Right
Thanks so much my God bless you
It can be done using a contractor having one NO and one NC contacts (230v coil supply) . If using this way, the wiring become more neat and beautiful. If we use an intermediate switch,it be different look than other two. If follows the circuit in the video it will not give indipendent control.
In hotels once you enter you switch on the bed room control switch. Later alternative switches. But either side switched are independent. But the same bulbs have independent control at the opposite mirror side. Suppose you get you can still switch on the bulb at the dressing mirror area. Next thing is regulated lighting. The passage light blow could be reduced by regulator, and it helps to increase when needed at night again reduced to low light then in the morning you are either switch off by regulator or by switch. Today many many inventions has come.
ਗਲਤ ਹੈ
ਇਹ ਸਰਕਟ ਠੀਕ ਨਹੀਂ
▀▄▀▄3 way ਕੰਟਰੋਲ ਨਹੀਂ ਹੈ ▄▀▄▀
According to circuit shown we can control infinite switch for one bulb and to off the bulb you should cut the fuse of building 😂😂😂
Newton kidhar Diya bhai
so beautiful job can you favour meconnection serial board testerok cereal wall tester making
Ek switch se on kro ar duse switch se off karke bato khas krke bich wala switch se
Muy bueno yo lo hacía utilizando un interruptor de cuatro vías en el tercer conmutable ,gracias aprendí algo nuevo.
Eso no funciona como debería, si te das cuenta. El interruptor que recibe la corriente siempre debe estar en una posición específica para que los otros 2 funcionen. Si el primer interruptor cambia de posición, los otros 2 dejarían de funcionar
@@xxcristhopherxx Exacto uno de los interruptores debe ser de doble vía para poder encender de uno y apagar del resto y viceversa...
Wow very good video
Informative video
Thanks for sharing
Parabéns pela demonstração desse sistema four way de interruptores,vou fazer um teste aqui em casa.gostei muito e é seguro e eficiente.
هذا الرباعي توجد به أخطاء في اعتقادي أنه ليس بكهربائي لانه توجد أجهزة سهلة ومتوفرة ليست بها تعقيدات .
Não é four way.
Dho double-pole switches kaafi haiñ
Your vidio is very supper, my langeg
Very good information 👍 Thank you
Sar ek number se shuru karke do ya teen number se band karo bahar se shuru karke andar jakar band hona chahie
Intermediate switch ka avishkaar nhi hua tha kya jab aapne ye wali video banai thi
3 switche ka faida kya hai? 🤔🤔
Bhai ek Jagah se on karna Ek Jagah se off karna Aisa dikhao
Está bien él vídeo pero él idioma no lo entiendo gracias muy bueno
1 switch on another off good you makeing same switch on same off no good all people have malum okay😂😂😂😂😂
Nice information for electrician
Ise Stair-case switch kahaa jaathaa he.
This circuit is from a true ghamad
supply के तारों को स्पष्ट तौर पर नही दिखाया गया है।
Very good idea
You can't off with ather switch
Should be on from one then off from 2nd or 3rd
Center main intermediate switch chahy
jahase on kiya ohise hi off hotahe ya jis sw se on karke koi vi sw se off kar sakte kya.
First view sir
ek se on dusre se off aur tisre se on kar k dikhao
Birinde kapat digerinde ac sonra digerinde kapat 3 cusunde bakalim olacak mi
Ager Tino switch on krde to kya hoga
هناك ادوات كتيرة موجودة وسهلة ولا تتطلب تعقيدات مثل cruze y conmutador suficiente para hacer cualquiera aparte los telereptores y ascensores del movimiento y muchas cosas
On off to kar dakte ha sabhi switch se but 1no. Se on karke 2 no. Se off krke dikhao
2 ki jagah 3 wire kyon liye 1 switch badha dete
Muito bom .3 comandos sem fazer uso do interruptor intermediário (four way).very Nice.
Phely 2 switches ma cross kr ky Q lagaye ha wire??? Stair case ki tarh sedhi wire nahi laga sakty?
Eu não achei correto: em um corredor longo o certo é colocar interrupitor paralelo em cada ponta e varios interrupitor inverssor de faze sendo um em cada porta exemplo corredor de apartamentos
Ele montou errado enganou ele mesmo
टूवै सै तीनो जगह सै कन्टोल सम्भव नही
1चालू 2 सै बन्द 3सै चालू 1सै बन्द कर दिखाये
Yeh toh one way switch se bhi kya ja shakta thaa😑
Water pump ko iss tarah connect kar sakte he kya
Tullu pump ke Aise connection kar sakte hain
Debarias prender con un botón y luego apagar con el siguiente y luego prender con el último botón
Por éso el video no me convense.
lakin apne yeh nai bataya k konsi wire apne kiske saath Q jori .. why cross wiring .. I click on your video but stopped watching because you didn't explain what are you doing and why are you doing? next time when you upload video do please answer WHY?
bhai kya hum 1 kamra jisme 3 bulb or 1 fan lagana hai toh usmein 1.5 mm phase or 1 mm neutral wire ka use kar sakte hai
Basta mettere tutti gli gli invertitori che vuoi al centro dei due deviatori è accendi e spegni da tutte le posizioni che vuoi. Altrimenti con un relè passo passo e dei semplici pulsanti con due fili accendi e spegni tutto quello che vuoi
El circuito no sirve. Siguiendo la línea de corriente, el primer y segundo interruptor siempre tendrían que estar apuntando a la misma línea de cable, si el primer y segundo interruptor apuntan hacia arriba, el foco nunca se apagará. Así de simple. Pará ese tipo de circuitos se fabrico el interruptor de 4 vías, ya que es la única solución para que el circuito funcione con 3 o más interruptores.
wrong connection hai, akk se on huto dusre se off nehi hota haii, ase video banake mot bhejiye,
totali useless work
❤❤❤❤
Não dá certo se acender a luz pela tecla do meio a terceira tecla não apagará a luz em qualquer posição
Bhai newtrall kaha sa lagaee plz btao ga
Dono ko on kijiye
Essa coisa em português já não é fácil imagina em grego, fala português poxa.
Ele tentou fazer um four way , mais não funciona . O mais fácil e correto é usar o interruptor intermediário correto e não ter fadiga. kkk...
Switch ko sedha karlo
Như vậy bật chổ này tắt chổ khác được không
Guru ji ko koi batye ki 1 se on to 2 se off hota hai, paglu ekhi switch se on off kar raha hai, pol tab khule jab sahi se bataye do switch ek jaise hi joda hai
Kya bhai.isme twoway switchka jaruret kyakeliye one way switchese banavo.verybad
Good
सभी को एक साथ चालू कर सकते है क्या
buon lavoro. bravo
Nice Explain Brother 👍 tq so much Brother 💐
Mcb board conesion kiya jata hai
पहले बिजली कनेक्शन की अच्छी जानकारी लो फिर विडिओ बनाओ, इस तरह लोगो को बेवकुफ मत समझो।
😂😂😂😂😂
Ek switch se light bulb jalawo doosri jagah se of karo hota hai kiya
yes
There are many better and easy methods.
like?
Best
یہ صرف 2 وے سوئچ ٹھیک کام کرتا ہے ۔۔۔۔
یعنی آپ نمبر 1 سوئچ کے ذریعے اگر بلب آن کرتے ہیں تو نمبر 2 سوئچ سے آف کر سکتے ہیں اسی طرح اگر نمبر 2 سوئچ سے آن کیا ہے تو نمبر 1 سوئچ سے آف ہو سکتا ہے ۔۔۔۔۔
لیکن اس میں یہ ہے کہ جس سوئچ نمبر سے کیا اسی سے آف کرنا پڑے گا
Olá muito bom seu vídeo parabens mêsmo amigo muito legal valeu
Aa
3 jagah ke liye 4 switch chahiye sir
Aese krna hoto 2 pin ka h swich hi kam kr leta h
Hello sir
This is wrong
Bulb ko aik switch sey on karo aur doosrey switch sey off karo phir pata chaley ga
Is main aik switch Intermidiat use ho ga phir sai kaam ho ga
very cool video
Kya aek hi switch se on off ho Ga, jaise ki aek switch bulb ko on krna, Aur dusre switch Se off krna, aisa ho Ga ki nahi,
hoga