MY TRANGIA TRIANGLE SETUP.
ฝัง
- เผยแพร่เมื่อ 14 ต.ค. 2024
- My Trangia triangle setup. The full setup was used for moto camping but it is adaptable for backpacking as well when stripped down.
The use of the spare burner stand as a mug mod is shown in full in this video:
• Trangia Triangle mug mod
Thanks for watching.
Link in the description to the video showing the burner stand mug mod.
Thanks for sharing.
Apologies if this is not clear.
Y pot support.
If the Triangle side supports are at the correct height then your extra ring sits too low.
Get a stainless steel spoke 305mm nip off the J end and the threads the other end. Bend in half, allowing the bend to be open.
Open out the two top sections to 120° to form a Y, (the vertical being double ), allow about 15mm overlap of the Triangle sides, on the 2 parted ends, these will rest in the furthest of the 2 scalloped pot supports of the side plates. Open the vertical of the Y to rest in the 2 scallops. = A pot support for all smaller pots than the Triangle at present accommodates.
If you do want it (the Y pot support) at the lower side wall height, you can do that too.
Add a u notch in the side walls to locate the Y if positive locating is desired.
@@taber247 I have another video that explains the pot support and it works fine with a titanium mug. The video is called the trangia triangle mug mod. Check it out😄
There are lots of different solutions for smaller pots for the triangle and all work. Thanks for sharing yours. I used to use something similar.
Thanks for sharing.
Even Trangia's gas appliances's fuel line touches underside of the base slot.
In one of the side plates, I have drilled a, same diameter hole, in the centre of the upper line of holes, on the same centre line. Then, from the existing fuel line slot snipped up to form an inverted T slot for the fuel line, also generously rounded off corners. This allows the fuel line to take a natural unstrained path out of the Triangle.
@@taber247 Yeah, that is what I'm going to do. I don't like putting strain on the fuel hose. One of the people I follow on Insta did the same. Quite an elegant solution. I take it you used snips, not a Dremel. I would probably do the same.
I don't have the same problem when using my edelrid hexon with the tradapter in the Triangle. It sits lower and the hose is more flexible. I've still to try the Robens fire tick in the triangle. I've only used it in the T27. It also sits lower below the burner stand so probably threads through easier.
I never used the older Trangia gas insert but it seemed to fit fine in pictures. Strange that they didn't quite get it right with the new one. Maybe there is a Mk3 triangle in the pipe line.
Is that the soto long spoon ??? . I was going to get one, but it was out of stock, then I forgot about it. Good video, thanks for sharing. Take care out there.
As always, thanks for watching.
It is the UCO switch spork. Quite handy as it snaps together to make a long spork. I've got a vid scheduled about sporks, of all things, but have acquired a jetboil sporks set since then which is really nice. I haven't seen the Soto long spoon. Might have a Google.
@@BrokenBackMountains you know !!!? I do believe it was the uco. No wonder I forgot , then couldn't find it.... cheers pal.
@@littlegrandadoutdoors They sell em on Amazon.
Why are you sending me this. I don't want it and I haven't subscribed.
@@TheBikerDodgeSorry, I'm not sending you anything.
You tube presents it to people and it is outside my control. If you don't want it, click on don't recommend channel. You won't see anything from my channel again.
That is the way TH-cam works, you have previously commented on the channel so it presents to you again.