Hello bro what sies it mean by Ac grid outrange... The inverter still red leaf although the output of inverter is within the ac grid
ปีที่แล้ว
Hi, do you know if a three phase inverter (MOD 3000 TL3-XH) is capable to push all it's capacity to one phase only if there is a high load on one phase, but no load on the other two phases?
@@suninhouse6988 at 5:30 timestamp of your video you talk about the Nline setting which you can enable or disable. What does this function do? Thanks for your help.
1.What is the correct voltage for the inverter to operate . Should it be above or below 230? 2. Which range should the inverter be set ? Should it be 0, 1, or 2 ?
Hellp, thank you for the video but can I ask aditional questions? I have to set parameters such as U > 1,1 pu; 30s (253 V, 30s) U >> 1,14 pu; 0,2s (262 V, 0,2s) U < 0,9 pu; 1,5s (207 V, 1,5s) U 51,5 Hz; 0,1s f < 47,5 Hz; 0,1s Any idea where I could do something like that? I installed growatt dongle (ShineWiFi-X module) but i cannot find such settings. Thank you in advance!
These parameters are an integral part of the standard on the basis of which power generators are connected to the grid. These parameters are changed when the standard is changed. From the prosumer's point of view, higher limits give better independence of the system with fluctuations in network parameters (fewer shutdowns due to exceeding the parameters). In Europe, each country has its standards, which are very similar, the main difference is the voltage limits. In this respect, the largest permissible ranges apply in Germany and Italy, and choosing the standards of these countries gives the greatest independence of the system from fluctuations in network parameters. Other parameters of the standards, such as frequency, phase shift, harmonic content coefficient, etc., are not subject to separate branches of the inverter firmware algorithms.
What is the difference between the level 0, 1 and 2 setting in Europe (in terms of actual voltage levels)?
Hello bro what sies it mean by
Ac grid outrange... The inverter still red leaf although the output of inverter is within the ac grid
Hi, do you know if a three phase inverter (MOD 3000 TL3-XH) is capable to push all it's capacity to one phase only if there is a high load on one phase, but no load on the other two phases?
no
Can I choose the output as 230v according to the datasheet?
Hello, what does enabling Nline does? There is no explanation about it anywhere.
What exatly do you mean? What Signal? What Connector? What Pin? Or other?
@@suninhouse6988 at 5:30 timestamp of your video you talk about the Nline setting which you can enable or disable. What does this function do? Thanks for your help.
This is enabling relays by enabling GND signails of its coils
@@suninhouse6988 do you have an example? I didn't understand what you mean well. Thanks again
There are digital outputc potential free contacts No&Nc driven by coils
1.What is the correct voltage for the inverter to operate . Should it be above or below 230?
2. Which range should the inverter be set ? Should it be 0, 1, or 2 ?
Range should be increased if over or under voltage occurs. Different countries have different low and up limits.
How to set date & time correctly on it 🙏
Hellp, thank you for the video but can I ask aditional questions? I have to set parameters such as
U > 1,1 pu; 30s (253 V, 30s)
U >> 1,14 pu; 0,2s (262 V, 0,2s)
U < 0,9 pu; 1,5s (207 V, 1,5s)
U 51,5 Hz; 0,1s
f < 47,5 Hz; 0,1s
Any idea where I could do something like that? I installed growatt dongle (ShineWiFi-X module) but i cannot find such settings.
Thank you in advance!
These parameters are an integral part of the standard on the basis of which power generators are connected to the grid. These parameters are changed when the standard is changed. From the prosumer's point of view, higher limits give better independence of the system with fluctuations in network parameters (fewer shutdowns due to exceeding the parameters). In Europe, each country has its standards, which are very similar, the main difference is the voltage limits. In this respect, the largest permissible ranges apply in Germany and Italy, and choosing the standards of these countries gives the greatest independence of the system from fluctuations in network parameters. Other parameters of the standards, such as frequency, phase shift, harmonic content coefficient, etc., are not subject to separate branches of the inverter firmware algorithms.
Hi, My inverter is on standby, help, please
What do you mean in standbay? If you bought from SunInHouse contact by phone or Messenger in working day.
IsGrowatt MIN 3000 TL-XH compatiple with APX-battery
Hello again I need for unitit Emirates
it is outside of the European Union so shipping costs are custom and you would probably pay some export duty fees.