Buffers vs Burnishers - Differences Explained

Compares and contrasts high speed floor burnishers (www.floorbuffers.com/high-spee...) and low speed rotary floor buffers (www.floorbuffers.com/low-speed.... Discusses appearance, operation, and uses of each.

[@RUready4DTruth]

Should have mentioned that a burnisher turns at a much higher rate of speed and "burnishes" the finish and should be kept in motion to prevent possible damage to tile. I don't recall ever making a "buffer burn" with electric but it is quite easy and common with propane. Great video though. Have a blessed day.

[@kaileighcullen2489]

RUready4DTruth of

[@cwootan80]

I need suggestions on a machine for a high gloss finish on urethane coated basketball court.

[@jeffreyk9743]

I need some advice on stripping , how do you strip 8 yrs of wax from a fake wood floor

[@reiniersacerio9334]

Can I use a 3000 grit pad with a burnisher and spray buff? Or just fo it with water?

[@sairaayala8506]

Where can I buy those machines?

[@alyisa12]

Is there a single machine that takes the place of a high speed and low speed?

[@sbud456789]

Question. Why am I getting Shine lines? Do you know what I'm talking about?

[@JaySirRoyal]

Too much buffer

[@ahammedshafi6809]

Very good

[@Thunderdad974]

When I burnish a floor with a battery operated walk behind burnisher, there are black "chips" in the pad and my wax is scratched. Do you know what is happening?

[@arod1391]

What pad were you using?

[@TheFloorBuffer]

No, a brush can not be used on a high speed (over 1000 RPM) machine. You can, however, use a brush on a low speed (175 RPM) rotary machine.

[@shellyth5700]

I would add that you should NEVER put any kind of scrubbing, or stripping pad on a burnishing machine. The friction of the pad and the floor will cause it's motor to overheat from lack of torque(turning strength)power, and the pad will possibly tear apart from turning so fast, with the overly high friction. I have seen and experienced this first-hand. I wish I had been taught that beforehand.

[@princekunle9650]

what is the price and how can i get it in Nigeria (Lagos)

[@bowserfrom9826]

are the both machine s good for stripping

[@lamontmitchell2988]

Take

[@TheFloorBuffer]

As a general rule of thumb, high speed burnishers generally cost more than low speed rotary machines.

[@TheFloorBuffer]

No, a high speed machine can NOT be used for wet stripping. High speed burnishers have a single purpose which is to achieve a high gloss/shine or "wet look" appearance on flooring surfaces. A low speed buffer machine can be used for wet stripping applications.

[@paulwang2604]

TheFloorBuffer thanks

[@TheFloorBuffer]

No, a low speed (175 RPM) would be the machine to use for wet stripping applications.

[@popeyesh8790]

What's the difference between burnishing&buffing.these does the same job?in the floor ,thanks.

[@jeffreyk9743]

I know this may be off the subject here, does anyone know how to go about getting certified as a floor tech

[@codymclean9733]

I would check out APPA or Bruco. Some janitorial suppliers should be able to direct you to some places.

[@jeffreyk9743]

Cody McLean Thank s Cody , I love what I do, would love to do it outside of retail though

[@markfurrer190]

+Jeffrey K your certified ,,,,good luck

[@TheFloorBuffer]

At this time, there is not one single machine that can operate at both low (175 rpm) and high speeds (over 1000 RPM).

[@janilinknashville613]

Wow. good video thanks

[@Michael_78]

Sorry but I was kinda hoping the trigger was locked in the "on" position when you plugged em in.

[@TheFloorBuffer]

No, a brush can not be used on a high speed machine. It can, however, be used on a low speed or dual speed rotary machine.

[@charleslennonbaker]

You never place the cord on your shoulder!

[@GhostGrind]

why?

[@handyman7297]

This is a no reply guy