Thank you!!!! Just adjusted the tension nut and it fixed my problem!!! Would not of know this adjustment if not for your video!!!! It saved me weeks without my machine and travel to and from the closest repair place!!!
At 6:30 "... need to be installed with the CONVEX sides facing each other." For someone following the audio here, this is important. Actually, it's important in simple reality.
Thanks so much, I hadn't used my Longarm in a long time and went to change the tension pads which mine has round felt pads (1999 Gammill Optimum and couldn't remember for certain which way the parts came apart but this helped to make sure I put it back together right.
Hi. This is a great video. I need to fix the tension assembly that I took apart while cleaning it. I do not have the book for the machine. There was no cone spring and there is no tension barrel. The check spring was not moving when I was sewing and the threads would pull out out of the fabric. Do all tension assembly’s have a cone spring? Maybe I have a machine with a missing part. It was purchased used. This is a Brother VX808. I would any insight you can provide.
When looking at a bowl or plate as it sits on a table...the bottom is convex in configuration and the top is concave, anything shaped outwardly is convex, inwardly (as with a cave) is concave. Good video.
I have a brother db2-b755 -3b but the check spring cylinder does not come out the machine even when I pull the set screw. Please can you tell me how to remove it
I thought this was a great video. I would like to see a video demonstrating the proper setting of top tension. Specifically, I would like to see the how the spring behaves with proper tension. Does the thread pull the spring over to the stop completely or should it be balanced between the limiits of the spring movement.?
Is it the 'concave' sides of the 2 tension discs that FACE each other or the 'convex' sides that FACE each other? It looked like the convex sides face each other on the video.
One other thing...some tension assemblies have a small metal pin that is loose inside the assembly..be careful that it does not fall out and get lost (been there, but found it). TinLizzie18 products have this type of pin. It goes into the assembly at the back..same way it came out.
Hi, thanks for the video... i have a Singer 368 and the thread tension regulator isn't held on with a screw... the screw is hidden somewhere. Do you know how i might remove this complete device? i have tried most everything! and its working improperly so i need to replace it. when i thread it, its all good,,, but as soon as i sew, the device pulls the thread out from between the discs. :/
Hi` a nice tutorial thank you,I now own a 132k6 singer that has this type of tension adjustment`but I also have another tension adjustment above the one your showing as well` but with no check spring`it just has two disc`s and a coil spring and a circular nut to place pressure on the spring which puts pressure on the discs . I know thread runs through this first tension then the thread goes to the one you describe,But why do I have the one above as well lower down on my machine .and which one do I adjust to place tension to correct my tension so my thread has the same tension to my bobbin.God how many times have I mentioned tension LOL.
Thank you!!!! Just adjusted the tension nut and it fixed my problem!!! Would not of know this adjustment if not for your video!!!! It saved me weeks without my machine and travel to and from the closest repair place!!!
Excellent presentation ... Thank You ... I for one, appreciate it .
great explanation. thank you so much Jason!
thank you so much I've been struggling with this for months. was very helpful
Thanks man, really helped out my dad and I to fix mom's sewing machine
Good instruction. Easy to follow, thanks. 😊
The best tutorial !
Thank you.
I subscribed just in case .
Thank you.
🙋🏼♀️
Exactly what I was looking for.
maybe, if not, the best video on this subject on youtube!
Congratulations!
really useful for my sewing machine. .. thanks for the wonderful video. .. now my machine stitching very nice. ..
At 6:30 "... need to be installed with the CONVEX sides facing each other." For someone following the audio here, this is important. Actually, it's important in simple reality.
Thanks for this, very clear and easy to understand.
Thanks so much, I hadn't used my Longarm in a long time and went to change the tension pads which mine has round felt pads (1999 Gammill Optimum and couldn't remember for certain which way the parts came apart but this helped to make sure I put it back together right.
Thank you very much for this video, hope I can fix my upper thread tension tonight.
You're the best.
Thank you
You really helped me .
Very helpful
Thank you! Used this to figure out my new (used) industrial juki!!
Hi. This is a great video. I need to fix the tension assembly that I took apart while cleaning it. I do not have the book for the machine. There was no cone spring and there is no tension barrel. The check spring was not moving when I was sewing and the threads would pull out out of the fabric. Do all tension assembly’s have a cone spring? Maybe I have a machine with a missing part. It was purchased used. This is a Brother VX808. I would any insight you can provide.
When looking at a bowl or plate as it sits on a table...the bottom is convex in configuration and the top is concave, anything shaped outwardly is convex, inwardly (as with a cave) is concave. Good video.
You're great sir but how do you fix it back to your machine?
Thanks, I appreciate this simple explanation.
Thank you very much. I appreciate your lesson; just save my old sewing machine. :}
Thanx a million.greatings from surinam
I have a brother db2-b755 -3b but the check spring cylinder does not come out the machine even when I pull the set screw. Please can you tell me how to remove it
I thought this was a great video. I would like to see a video demonstrating the proper setting of top tension. Specifically, I would like to see the how the spring behaves with proper tension. Does the thread pull the spring over to the stop completely or should it be balanced between the limiits of the spring movement.?
Thank you !!
You helped me save money 👍🏼👍🏼👍🏼👍🏼
somehow my 66 tension became way off, I messed with it way too much, your video reminded me the correct way. I'm back in the "tension grove" Thankyou!
An excellent info. Thank you very much
Such an excellent video, thank you
Thank you for sharing
Thank you so much
Is it the 'concave' sides of the 2 tension discs that FACE each other or the 'convex' sides that FACE each other? It looked like the convex sides face each other on the video.
One other thing...some tension assemblies have a small metal pin that is loose inside the assembly..be careful that it does not fall out and get lost (been there, but found it). TinLizzie18 products have this type of pin. It goes into the assembly at the back..same way it came out.
I have a kenmore sewing machine I need to know how to assemble my tension piece by piece, not all tension are alike my machine is a Kenmore
Hi, thanks for the video... i have a Singer 368 and the thread tension regulator isn't held on with a screw... the screw is hidden somewhere. Do you know how i might remove this complete device? i have tried most everything! and its working improperly so i need to replace it. when i thread it, its all good,,, but as soon as i sew, the device pulls the thread out from between the discs. :/
Can you do a video on the tension assembly of an Elna Air Electronic ? thank you
will this tension assembly fit the Consew cp206R thanks...H.Paine
Hi` a nice tutorial thank you,I now own a 132k6 singer that has this type of tension adjustment`but I also have another tension adjustment above the one your showing as well` but with no check spring`it just has two disc`s and a coil spring and a circular nut to place pressure on the spring which puts pressure on the discs . I know thread runs through this first tension then the thread goes to the one you describe,But why do I have the one above as well lower down on my machine .and which one do I adjust to place tension to correct my tension so my thread has the same tension to my bobbin.God how many times have I mentioned tension LOL.
lettherebe piece
Can you fix a viking rose tension knob? its computerized and will only go to 4 and wont move anymore (thread broke and since knob wont move more)
Good sir
Do you know where to buy this tension assembly?
Needle thread tension + pfaff 260 please how are ensambly
I have problem with thread tension .Can you help me
I want to see how he install it to the machine itself
Thanks!
I fix my old Pfaff sewing machine , i follow your instruction.I like your video but video need more loud sound. Thank you so much.
You are great sir ThanQ so much for this vdo
Great video.
Thank you for video it's work
Thanks so much for this information!
thank-you, thank-you, thank-you!!!!
BOM DIA ! Pra mim é uma honra esta aqui te prestigiando, vamos sempre juntos somar e fortalecer nossos trabalhos, eu já estou por aqui,,,
Thank you.
is this why my stitches are not tight enough on my Juki?
GREAT tutorial! my gizmo is different than yours so I'm afraid to try to dissassemble it ... thank you anyway =)
Helpful
Nice
Thanks, very helpful
I have a necchi and need help
you da man
Is that a lite wisp of a mustache shadow
Hi expect
You are great sir ThanQ so much for this vdo