Hi Justin, tx for the video, very helpful, I have a question, After drying out my phantom 3 standard, from a fall on a fountain, and starting it up, and seen that camera and gimbals are working correctly, I need to test the motors, one by the looks of the coppers wires it looks likes it overheat, and I was wondering if I should replace it first, just in case It is damage, or should i try it first???? I just don't want to damage the main board. What is your advice?? Sorry for my english. Joaquin From Argentina.
Good evening, I have a Phantom 3 ADV and my control (RC) is indicating the battery charging up to the third light. I noticed that there is an electronic component that is responsible for the indication of the fourth light (components - 4407A and P2664). Do you know what it would be?
my RC does not fully charge the battery. I have reviewed several TH-cam videos of people with the same problem, but no one has indicated which electronic component needs to be replaced on the Phantom 3 ADV RC mainboard. Can you help me?
nice video justin, nice solder joints as well, i found that the gimbal has 2 tabs on it that people say house the antenna connectors for the video (2.4gig) and they go up to the side of the battery bay, my antennas seem a little covered and im constantly loosing video in the city and other areas that are noisy, my local rc shop sells this connector that supposably allows me to unplug the standard antennas, leave them there and add wifi boosters and a high gain antenna, does this do anything and thanks justin for the demo
I know this is a old video. But im having a issue. You probly wont reply but worth a shot. So i new to this but smart i bought a used p3 s. Ass guy left guard screws in and bam so on motor didt soi. Really rest did so i followed you vid. Sober is shiney and i turned on the drone before closing and the motor was spinning fine made a little noise but i couldnt tel from where. But closed up tossed on props. Amd now when it starts it fires up all spinning great but if i it up right away it goes but you can tel that the motor isnt insync or putting out the same amount of power i hit left right yaw fine but once i make a moove up it turns over.????? I dont understand its not wrong motor same exzact one not wrong direction cause it will go up butit shakes and basicly wants to fall .. Ita ust not in tune with tw other motors??is it tje esc?? Am i screwex and have to buy a mother board .. I hope you give a answer thanks
Hello guys! Yesterday my Phantom 3 ADVANCED had a fall due to a momentary "imbalance" during takeoff. I noticed that he was NOT fixing his position (not stabilizing via GPS) and did not want to take flight ... I was watching because he presented some movements that are not common to him (rapid twitches). When I was close to the ground, he PLAYED sideways, very fast, and fell with the propellers to the ground, without being able to turn it off by the remote control. I had to PULL and TAKE his battery. After that, the messages on the DJI GO screen appear WARNING: MOTOR OBSTRUCTED. Does anyone know what it's all about? Well I called him again and he seemed to be "normal" but I'm afraid to get him up again ... Thank you if anyone knows how to report. EDU!
![KRK - ชนิสรา Ft.WanMai , N/A [Official MV] Prod. By Sakarin](http://i.ytimg.com/vi/C-WMwwYobcU/mqdefault.jpg)
Yep, I did the long screw thing! Thank you for a very thorough guidance of how to do this yourself.
Omg this guy should be a teacher!!! He explains everything so well!! Lots of great tips!!
Thanks for this video and detailed walkthrough. You saved us a lot of trouble/headache by doing this. Very grateful.
Yw Geoff!
thanks for the video...very good details...thanks Justin
Hi Justin, tx for the video, very helpful, I have a question, After drying out my phantom 3 standard, from a fall on a fountain, and starting it up, and seen that camera and gimbals are working correctly, I need to test the motors, one by the looks of the coppers wires it looks likes it overheat, and I was wondering if I should replace it first, just in case It is damage, or should i try it first????
I just don't want to damage the main board. What is your advice??
Sorry for my english. Joaquin From Argentina.
Excellent review Justin!!
Very thorough video. Thanks.
nicely done brother
where can i purchase Phantom 3 standard CCW orig motor?
Very detail video JD. Thanks bro
Yw Ted!
Nice Job bro.. your the man
Good evening, I have a Phantom 3 ADV and my control (RC) is indicating the battery charging up to the third light. I noticed that there is an electronic component that is responsible for the indication of the fourth light (components - 4407A and P2664). Do you know what it would be?
my RC does not fully charge the battery. I have reviewed several TH-cam videos of people with the same problem, but no one has indicated which electronic component needs to be replaced on the Phantom 3 ADV RC mainboard. Can you help me?
Thanks.
My motors are good but they make a very loud noises. Not sure if they need to be replaced or if they have a life limits???
They shouldn't make any noises at all.
nice video justin, nice solder joints as well, i found that the gimbal has 2 tabs on it that people say house the antenna connectors for the video (2.4gig) and they go up to the side of the battery bay, my antennas seem a little covered and im constantly loosing video in the city and other areas that are noisy, my local rc shop sells this connector that supposably allows me to unplug the standard antennas, leave them there and add wifi boosters and a high gain antenna, does this do anything and thanks justin for the demo
thank you so much. i dont know if i will do this right tho
awwwww i thought you'd be opening up some brushless motors for repairs not just replacements
I know this is a old video. But im having a issue. You probly wont reply but worth a shot. So i new to this but smart i bought a used p3 s. Ass guy left guard screws in and bam so on motor didt soi. Really rest did so i followed you vid. Sober is shiney and i turned on the drone before closing and the motor was spinning fine made a little noise but i couldnt tel from where. But closed up tossed on props. Amd now when it starts it fires up all spinning great but if i it up right away it goes but you can tel that the motor isnt insync or putting out the same amount of power i hit left right yaw fine but once i make a moove up it turns over.????? I dont understand its not wrong motor same exzact one not wrong direction cause it will go up butit shakes and basicly wants to fall .. Ita ust not in tune with tw other motors??is it tje esc?? Am i screwex and have to buy a mother board .. I hope you give a answer thanks
peace be upon u , if one of the motorr damaged could the drone keep working !! i have one motor damaged but it wont turn any one of them ?
How do you like that hakko ?
Love it so much I have a second for back up
Sweet
When it comes to maintenance, is it a pain on the phantom? I ask cause I'm still deciding between the phantom and the maverick
Phantom will be easier than the Mavic.
Thanks for the input. Gonna make shopping easier
after disassembly the magnets began to touch the rotor. What? I did everything as on the video.
Hello guys!
Yesterday my Phantom 3 ADVANCED had a fall due to a momentary "imbalance" during takeoff.
I noticed that he was NOT fixing his position (not stabilizing via GPS) and did not want to take flight ... I was watching because he presented some movements that are not common to him (rapid twitches).
When I was close to the ground, he PLAYED sideways, very fast, and fell with the propellers to the ground, without being able to turn it off by the remote control. I had to PULL and TAKE his battery.
After that, the messages on the DJI GO screen appear WARNING: MOTOR OBSTRUCTED.
Does anyone know what it's all about?
Well I called him again and he seemed to be "normal" but I'm afraid to get him up again ...
Thank you if anyone knows how to report.
EDU!
thanks for info! need a better soldering gun!😁
gun?
i thought dji used esc's but they used all in one fc
After the P2 they stopped :/
??????
It still uses ECS's. They just happen to be soldered on the motherboard now, that's all.
I just did that... it sucks!
Rookie error:)
Haha. ⚡️🌿