Container construction - The foundations: pouring concrete, making blocks

แชร์
ฝัง
  • เผยแพร่เมื่อ 4 ธ.ค. 2020
  • Following the foundations of our container construction: we pour the concrete and make the blocks.
    Today we are moving on to the next step: pouring the foundations and making the blocks on which the containers will rest.
    J -21
    The studs: 50 centimeters on each side for single studs and 50 centimeters by 80 centimeters for double studs.
    The quantity of concrete to be poured: 4m3, for this quantity it is easier to order a truck-mixer than to do it on site.
    We put a few centimeters of concrete at the bottom of the excavation and we place the reinforcement then we finish by filling up to the desired height.
    It is a fairly quick operation since the truck stayed barely 1 hour on site. The actual pouring work lasted only 20 minutes.
    It must be left to dry for a week before the next step.
    J -18
    The work begins with the realization of a new and even more precise tracing. This operation must be carried out with great rigor. We check the distances and especially the squareness.
    It is very important to have a perfect tracing because the containers being products made in an industrial way, they have dimensions precise to the millimeter and they are perfectly square. From now on, we trace the markings on the foundations, which is simpler.
    The forms will be held on the foundations by metal rods and adjusted with wooden wedges so that they do not move when the concrete is poured.
    The reinforcement intended to reinforce the concrete is taken in the foundations with chemical sealants.
    Here is what it looks like before the formwork is put in place, here for a single stud and there for a double stud.
    As you will see later, the containers being attached to the existing house, the foundations for the container should be placed as close as possible to the foundations of the house. This is what we are doing here.
    The formwork is made to measure and on site.
    The plates have arrived. Ideally they should be galvanized to protect them from corrosion. But as we are in a period of confinement this operation could not be done. They are protected by anti-rust paint.
    The formworks have been installed. They were planned a little higher than the desired level and markings are made all around with the laser level. These marks will be used to position in height the plates on which the containers will rest.
    J-15
    The concrete is poured and the height of the plates is adjusted with the laser level. This step is very important. It is important to be sure that the levels are right because the slightest significant deviation would put the containers in overhang for example and make the operation complicated or even impractical.
    In theory a container needs to rest on these 4 corners. As far as we are concerned, we started on a much larger number of studs because we are going to make openings inside these containers which will weaken them. So to make sure that we keep the integrity of the containers, we have practically doubled the number of studs.
    Once finished, we have to wait 3 weeks of drying to proceed to the next step, that is to say the long awaited break of the containers.
    While waiting for the drying of the blocks, we finalize the evacuation of rainwater with the construction of a new sump.
    Our house already has one but it will not be sufficient to receive the additional water from the roof of the containers, i.e. almost 90 square meters. We will see in another video the installation of the rainwater network and the manholes.
    The sump: a large deep hole in which we place a concrete well around which we place large gravel. A pipe will bring the rainwater which will be evacuated naturally into the ground. The whole is covered with a layer of earth. Afterwards you can't see anything.
    Note that a sump must be located at least 3 meters from the foundations of your house.
    We meet again for the next video where we will see the lower part of the containers, i.e. the stone work and the insulation.
    TH-cam: / @kerworkshop
    The video: • Construction container...
  • แนวปฏิบัติและการใช้ชีวิต

ความคิดเห็น • 34

  • @memphisscorp6121
    @memphisscorp6121 3 ปีที่แล้ว +11

    Bonjour,
    Je trouve l'initiative de partager votre projet très sympa.
    Nous avons ma femme et moi dans l'idée de construire notre maison entièrement en container, et vos vidéos sont très instructives.
    Bonne continuation.

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว +1

      Merci. N'hésitez pas à vous abonner si ce n'est déjà fait, vous pourrez suivre l'avancement du chantier au fur et à mesure.

  • @renaudhaeckler9448
    @renaudhaeckler9448 3 ปีที่แล้ว +1

    Merci pour les vidéos :)

  • @karimnajah3479
    @karimnajah3479 3 ปีที่แล้ว +1

    Bon travail

  • @samiabadache9572
    @samiabadache9572 2 หลายเดือนก่อน

    Merci,par contre j'aurai souhaité que vous affichez le plan de fondation comme support de votre explication

  • @MRJOYCE
    @MRJOYCE 3 ปีที่แล้ว +5

    Bonjour,
    Pourquoi n'avoir pas coulé les paniers avec du ferraillage d'arrachement directement ?
    pour ainsi éviter de pércer le béton déjà couler et le fragiliser malgré le scellement chimique, gain de temps et d'argent ?
    Merci

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว +1

      Oui, effectivement, mais c'est la méthode choisie par notre maçon. Elle à malgré tout l’intérêt de pouvoir positionner précisément les ferraille "au dernier moment".

  • @madjid8793
    @madjid8793 2 ปีที่แล้ว +1

    Bonjour M.
    Quel est le coût total de cette construction ?
    Je vous remercie

  • @florianbouvet7055
    @florianbouvet7055 3 ปีที่แล้ว +1

    Le fait de tout détailler dans vos vidéos est vraiment top ! J'aimerais aussi construire ma maison en containers, il est nécessaire de faire une dalle ou de mettre des plots ? Merci !

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว +2

      Les deux sont possibles. A notre avis, l’intérêt de mettre des plots est plus économique, ce qui "logique" pour une construction container dont la motivation possible est la recherche d'un faible coût de construction. Lors de mes recherches sur internet d'exemples de maison containers, j'ai vu très peu de construction sur dalle. Par contre il ne faut pas se contenter de poser un container sur 4 plots seulement. 8 nous parait un minimum.

  • @omael6711
    @omael6711 3 ปีที่แล้ว +2

    Un grand merci pour tout !
    Peux-tu me dire combien elle t'a couté cette maison ?

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว

      Merci pour tes encouragements. On fera peut-être une vidéo "bilan" dans quelques temps, on en parlera à ce moment là peut-être.

  • @CharlesDerive
    @CharlesDerive 3 ปีที่แล้ว +2

    Bonjour , combien cela vous a coûté pour réaliser vos plots de fondations svp ? Cordialement

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว +2

      Merci de l'intérêt que vous portez à notre construction. Nous ferons dans quelques vidéos un bilan global de notre chantier. On donnera les chiffres à ce moment là. Il faut savoir que le coût des fondations et des plots varie beaucoup selon l'envergure du projet. Le mieux, lorsqu'on veut le faire faire à un professionnel, est de demander des devis à plusieurs artisans.

  • @meilleurvideotiktokmonde617
    @meilleurvideotiktokmonde617 3 ปีที่แล้ว +1

    Bonjour
    C’est quoi la plaque en béton qu’il met dans les plots ?
    Merci pour ses vidéo

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว +2

      Ce n'est pas une plaque en béton, c'est une plaque de métal qui est ancrée dans le béton. C'est sur ces plaques qu'on soude les containers pour les liaisonner au sol.

  • @karimnajah3479
    @karimnajah3479 3 ปีที่แล้ว +3

    Celui qui coupe le ferraillage à enlever le carter de protection de la Meuleuse. A ne jamais faire

    • @TheLdc38
      @TheLdc38 3 ปีที่แล้ว +1

      Lol, c'est le bâtiment collegues!!

  • @yacinekassa1539
    @yacinekassa1539 2 ปีที่แล้ว

    Bonjour je suis intéressé par se type de construction c'est possible de me mettre en relation avec votre constructeur.
    Cordialement

  • @kelymanda7695
    @kelymanda7695 3 หลายเดือนก่อน +1

    Bonjour, qui vend les platines svp?

    • @Kerworkshop
      @Kerworkshop  3 หลายเดือนก่อน

      je les ai fais faire par une artisan local.

  • @frantzyre7396
    @frantzyre7396 3 ปีที่แล้ว +1

    Bonjour,
    Merci pour votre dernière vidéo.
    avez vous rendu vos fondations étanches ??

    • @roycecoleman8292
      @roycecoleman8292 2 ปีที่แล้ว

      I know im asking randomly but does anybody know of a trick to get back into an instagram account??
      I was dumb forgot the account password. I would love any assistance you can give me.

    • @marcoshepard7850
      @marcoshepard7850 2 ปีที่แล้ว

      @Royce Coleman Instablaster =)

    • @roycecoleman8292
      @roycecoleman8292 2 ปีที่แล้ว

      @Marco Shepard Thanks for your reply. I found the site thru google and I'm trying it out now.
      I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.

    • @roycecoleman8292
      @roycecoleman8292 2 ปีที่แล้ว

      @Marco Shepard it worked and I now got access to my account again. Im so happy!
      Thanks so much, you really help me out !

    • @marcoshepard7850
      @marcoshepard7850 2 ปีที่แล้ว

      @Royce Coleman happy to help =)

  • @loiclebahezre3868
    @loiclebahezre3868 3 ปีที่แล้ว

    C est des fondations pour un immeuble de trois étages

    • @Kerworkshop
      @Kerworkshop  3 ปีที่แล้ว +1

      Non, juste pour nos containers... l'idée est de soutenir les containers à plusieurs endroits pour éviter une certaine souplesse et des éventuelles vibrations.

  • @clementcarbon2147
    @clementcarbon2147 ปีที่แล้ว

    j'ai eu un haut le coeur en voyant comment était fait les semelles de fondations. Vous devriez avoir honte de montré ça aux gens.

  • @tommackels9077
    @tommackels9077 ปีที่แล้ว

    Bonjour je vous ai envoyé un message par messenger pourriez-vous y répondre quand vous avez le temps svp ?