Happened to me today after I cleaned and lubed the chain on 1st gear. Knew I would get a solution in your channel. I was right. Thank you for helping the CB community ❤
@gianchavez2162 Traduciré a través de Google y te compartiré lo que estoy explicando en el video en algunos puntos. 1. Si lubricas la cadena o recientemente has hecho un lavado con agua, la luz del motor brillará 2. Nada de qué preocuparse, la luz se apagará después de recorrer unos pocos kilómetros. 3. O déjalo secar durante la noche y el problema se resolverá Si la luz del motor sigue encendida durante más de un día de conducción, es mejor visitar el centro de servicio Viaja con cuidado :)
@@halfbikr me pasa lo mismo pero no se borró en todo el día y eso manejando 40 kilómetros lo lleve al mecánico honda y no se que hizo y se fue pensé que era algo con el botón de encendido algún truco
Thanks for the clarification. Bought the bike with less than 4k km. I started to lube the chain and didn't noticed about it when i started to ride off and found the engine light up.
Samething happened to me today morning. It happens when you put the bike in centre stand and runs it for lubing at that point rear wheel is spinning but the front wheel isn't thats why its shows that warning. Turn the key on and off for 4-5 times and it turns off but it will be logged in the ECU
it's the ABS or most possibly the Traction sensors. When the engine is running and only the rear wheel spins then the sensors can't get the front reading so the warning light glows up. It goes off after a couple of kms of riding. It's a short term bug. SC guys are not very aware about this. Alert: You are not supposed to lube a running bike on the main stand, it's dangerous, many people got hurt and/or lost their finger.
Yeah i understand its messing up some sensors. But it happens only after lubing or water washing the bike. Also the warning you have shared is 100% true. I don’t do that 👍🏽
PGM-FI light came on after I lubed chain. Riding it a few km didn't put it out. What I did was this: with engine idling in neutral switch off traction control by pressing select button. Then switch off engine with ignition key and then restart it. The light then goes out.
Hey, I experienced this too, I lubed the chain and ran it in 1st gear on center stand. Then I switched it off and started the bike after two days, the light has lit up and not gone even after 20 kms of ride, let's see.
No action needed just drive it for few kms it will go off. Not sure if Honda is going to deal with this small bug which doesnt affect the performance in any sorts
so in my bike this indicator used to turn off once the engine starts. now after i installed extra lights, this engine light stays on. Do i have to worry ? or is it a bug ?
Currently in bigwing. Normally in Adyar, gave it in saidapet once but not satisfied so for nw my services will be in Adyar Bigwing bro. Are you looking for a local mechanic? Or are you asking for the authorised service centres?
Just bought the RS today , and while taking it home i noticed this light was up the entire time , i got a bit worried. I'll go for a ride tonight , hopefully it's nothing serious and will go away.
Facing the same issue now after water wash and chain lube with 1st gear engaged on center stand. Ridden 5 kms still engine check light is on. Hopefully this should disappear within a few more kms.
It will go away bro. And also never lube the chain while the bike is running on gear. Always rotate the tyre with hands and do the spray. It will be mote effective and it is safer also.
I lubed chain 2 weeks before keeping engine off i didn't faced any issue i rode bike few km .. Now nearly today after a week i started bike engine light came and not going rode around 4 km still light is on..😢
@@halfbikr thanks man.. I went out aging rode bike for nearly 10 km but still light was on then i just turned off ignition and started bike again light went off after that rode bike more 4 km light has gone now thanks..
Rs 350 Chain epdi adjust pannarathu slack epdi vaikanum?. Separately oru video poduga bro and aux light podalama ena brand aux light podalam and final PEA honda carbon cleaner nu normal honda showroomlaiyae kuduranga every 3000km ku use pannlamnu atha RS 350 ku use pannalama. Thanku in advance ♥️♥️🤝🤝
Hi bro, 1. Enaku exacta procedure thryathu, i have never adjusted the chain for my bikes, i normally take it to the mechanic.. venumna next time i will record that process and post it! 2. Aux lights podlam bro, many are using. Mad dog nu onnu iruku, thats the best one but it’s costly.. unbranded we can try but wiring elam corecta panirkanum ilen risk… 3. Personally i feel carbon cleaner is not necessary for a new bike, atleast for 50000kms you wouldn’t need it. Honda la vechurnthalum its a 3rd party product only. I wouldn’t recommend using it for now. Anyways i will make a research on that and let you know if it is a genuine product and if it is really useful. Ride safe!
This happened to me today after lubing the chain but after riding for 12 kms atleast the engine light is still not gone. Tried turning off and on plenty of times too.
Bro you don't know about this bike actually its the feature of this bike only, after oning key, before you self start you have to wait for some time until that symbol goes because the sensors will be checking the engine malfunction until then you have to wait and when the symbol goes off then you have to self start and ride
It will make a some electric like sound after sensors checked engine thoroughly and then it will off if no problem and then you have to self start then you can ride but if you do it early self start the symbol will remain until it checked your engine.
Bro that is when i click on the engine kill switch. But this happen when we ride the bike. The sound you say stops in one or two seconds but the light is still on.
@@halfbikr to avoid this problem. Before running the bike for chain lubrication on 1st gear. Turn off the traction control. This is solve the issue, it's due to the traction control. The sensor is probably confused if the traction control is on and the front wheel is stopped and real wheel is running 😅
@@halfbikr BigWing Saharanpur (Uttar Pradesh). Also, I guess rates varies according to different cities. In Delhi it is nealy Rs.200, in Coimbatore it is around Rs. 150. It should be same across all showrooms. One of my friend in Delhi was charged Rs. 1800 for 1st service but I was charged Rs. 1450 then I sent my bill to him and he got refund after a week.
![[DRIP] ‘Woke Up In Tokyo (RUKA & ASA)’ PREVIEW](http://i.ytimg.com/vi/QN44lcR_VkI/mqdefault.jpg)
Happened to me today after I cleaned and lubed the chain on 1st gear. Knew I would get a solution in your channel. I was right. Thank you for helping the CB community ❤
Anytime bro 💪🏼
@@halfbikr Hermano yt no sale la traducción de lo que hablas en el vídeo me puedes escribir por acá para traducirlo y saber cómo hacerlo ?
@gianchavez2162 Traduciré a través de Google y te compartiré lo que estoy explicando en el video en algunos puntos.
1. Si lubricas la cadena o recientemente has hecho un lavado con agua, la luz del motor brillará
2. Nada de qué preocuparse, la luz se apagará después de recorrer unos pocos kilómetros.
3. O déjalo secar durante la noche y el problema se resolverá
Si la luz del motor sigue encendida durante más de un día de conducción, es mejor visitar el centro de servicio
Viaja con cuidado :)
@@halfbikr me pasa lo mismo pero no se borró en todo el día y eso manejando 40 kilómetros lo lleve al mecánico honda y no se que hizo y se fue pensé que era algo con el botón de encendido algún truco
@gianchavez2162 Debe haber algún problema con el sensor. Me alegro de que se haya ido ahora
Thanks for the clarification. Bought the bike with less than 4k km. I started to lube the chain and didn't noticed about it when i started to ride off and found the engine light up.
Samething happened to me today morning.
It happens when you put the bike in centre stand and runs it for lubing at that point rear wheel is spinning but the front wheel isn't thats why its shows that warning. Turn the key on and off for 4-5 times and it turns off but it will be logged in the ECU
Yes. But after riding for less than 2kms also it will go away. Happened to me twice
Same thing happened with me.....On centre stand i have lubed the chain....then after symbol is appeared...but its not going...what should i do
Relax bro it will go off after riding for few kms. Dont worry
Thanks bro. You saved me a trip to the service centre 😂
Glad i was of help 😬
Thanks for the heads up i was worried the light has gone off after chain lube and riding for about 2kms
Hope i helped :)
it's the ABS or most possibly the Traction sensors. When the engine is running and only the rear wheel spins then the sensors can't get the front reading so the warning light glows up. It goes off after a couple of kms of riding. It's a short term bug. SC guys are not very aware about this.
Alert: You are not supposed to lube a running bike on the main stand, it's dangerous, many people got hurt and/or lost their finger.
Yeah i understand its messing up some sensors. But it happens only after lubing or water washing the bike.
Also the warning you have shared is 100% true. I don’t do that 👍🏽
Thnx so much sir, I was also scared and noticed that it happed after i applied the lube….
Just to clarify, it happened in Higness.
Yes yes bro ive seen the same issue in highness also. Hope it is gone now.
Thank you for highlighting this issue brother
🫡🫡
PGM-FI light came on after I lubed chain. Riding it a few km didn't put it out. What I did was this: with engine idling in neutral switch off traction control by pressing select button. Then switch off engine with ignition key and then restart it. The light then goes out.
Noted!
Hey, I experienced this too, I lubed the chain and ran it in 1st gear on center stand. Then I switched it off and started the bike after two days, the light has lit up and not gone even after 20 kms of ride, let's see.
Should wear off bro. The lube is jus messing with the sensor.
Hi, Lube is not messing up, but the rear wheel sensors misreading as the front wheel don't spin when on the main stand.
Any action should the biker take? Is Honda doing anything to fix this bug?
No action needed just drive it for few kms it will go off. Not sure if Honda is going to deal with this small bug which doesnt affect the performance in any sorts
so in my bike this indicator used to turn off once the engine starts. now after i installed extra lights, this engine light stays on. Do i have to worry ? or is it a bug ?
Might be some wiring issue, get it checked with a technician bro
Where do you service your bike bro I’m in Chennai only searching for a good mechanic
Currently in bigwing. Normally in Adyar, gave it in saidapet once but not satisfied so for nw my services will be in Adyar Bigwing bro. Are you looking for a local mechanic? Or are you asking for the authorised service centres?
Bro WD 40 chain lubing panan but i drived 30km but still indication is showing.what to do
Normally it goes off in mostly 4-5kms. Inum varuthu na take it to service center once bro.
Thanks for the video. I was worried after chain lube because engine light turned on. After few kilometres of ride,it disappeared
Glad i was of help ♥️
Same happened with me today.. thankfully it is gone now😅
Just bought the RS today , and while taking it home i noticed this light was up the entire time , i got a bit worried.
I'll go for a ride tonight , hopefully it's nothing serious and will go away.
It will go away bro. Nothing to worry. It it stays up for more than 10kms then check it with the svc
@@halfbikr thank you bro ! That relieved me a bit.
No problem bro. Anytime
@@halfbikr it did go away after riding it for 5kms! , thanks man you saved my time visiting the showroom!
@arjunmishra1050 awesome!
Facing the same issue now after water wash and chain lube with 1st gear engaged on center stand. Ridden 5 kms still engine check light is on. Hopefully this should disappear within a few more kms.
It will go away bro. And also never lube the chain while the bike is running on gear. Always rotate the tyre with hands and do the spray. It will be mote effective and it is safer also.
I lubed chain 2 weeks before keeping engine off i didn't faced any issue i rode bike few km ..
Now nearly today after a week i started bike engine light came and not going rode around 4 km still light is on..😢
Let the lube dry off bro. Its just messing up with a sensor probably. If the problm still is there then do take it tot the service center
@@halfbikr thanks man..
I went out aging rode bike for nearly 10 km but still light was on then i just turned off ignition and started bike again light went off after that rode bike more 4 km light has gone now thanks..
@niksaan100 great!
I just lubed my chain and engine check light is on. Should i take it to service center?
No need bro, ride it for 2-5kms. It will wear off and light will stop glowing. No need to worry
@@halfbikr
Yes, it went away after riding it for 5 km
Super
Thank you, bro. Thank you, thank you, thank you!!!
Anytime bro anytime!
That's a relief!
Yup
Thanks for the video brother. i just got my bike washed for the first time and the yellow icon just went on. i was worried.
Hopefully the warning is gone now!
Thanks bro.. i did a chain lube today.. and same thing happened.. thanks for the video.. it really helped.. first I was really worried..😅
Glad i was of help bro 🤙🏼
Thank you buddy you helped me ❤
🫂🫂
I cleaned my chain today and started the engine with 1st gear on double stand. I also faced the same issue. Hopefully it goes away.
It will go bro.
i think engine light shows only if your bike is on double stand ...right?
No bro. Not related to center stand
Rs 350 Chain epdi adjust pannarathu slack epdi vaikanum?. Separately oru video poduga bro and aux light podalama ena brand aux light podalam and final PEA honda carbon cleaner nu normal honda showroomlaiyae kuduranga every 3000km ku use pannlamnu atha RS 350 ku use pannalama. Thanku in advance ♥️♥️🤝🤝
Hi bro,
1. Enaku exacta procedure thryathu, i have never adjusted the chain for my bikes, i normally take it to the mechanic.. venumna next time i will record that process and post it!
2. Aux lights podlam bro, many are using. Mad dog nu onnu iruku, thats the best one but it’s costly.. unbranded we can try but wiring elam corecta panirkanum ilen risk…
3. Personally i feel carbon cleaner is not necessary for a new bike, atleast for 50000kms you wouldn’t need it. Honda la vechurnthalum its a 3rd party product only. I wouldn’t recommend using it for now. Anyways i will make a research on that and let you know if it is a genuine product and if it is really useful.
Ride safe!
@@halfbikr ♥️♥️♥️ thanku bruh.
How many kms will it take to go off brother?
Roughly 2-3kms bro
@@halfbikr thanks bro, it went off.
Thank you bro, happened right now, will it go away after riding, or overnight?
Ya bro it will stop glowing after riding for few kms.
@@halfbikr okay, thanks 🙏
Ride safe! :) and don’t forget to subscribe 😬
This happened to me today after lubing the chain but after riding for 12 kms atleast the engine light is still not gone. Tried turning off and on plenty of times too.
Let it dry out tonight. If the light is still on tomoro, its better you take it to the service center once..
Thanks 👍
Seriously bro ....i was so worried i git honda rs yesterday today i put some lube and favcing this problem lts see what will happen
It will go away bro. No worries
❤
Bro you don't know about this bike actually its the feature of this bike only, after oning key, before you self start you have to wait for some time until that symbol goes because the sensors will be checking the engine malfunction until then you have to wait and when the symbol goes off then you have to self start and ride
It will make a some electric like sound after sensors checked engine thoroughly and then it will off if no problem and then you have to self start then you can ride but if you do it early self start the symbol will remain until it checked your engine.
Bro that is when i click on the engine kill switch. But this happen when we ride the bike. The sound you say stops in one or two seconds but the light is still on.
@@halfbikr my showroom manager told like that, it may be on if sensors are exposed to water also so have to wait to dry out.
Ya very rarely it is on after a water wash. But after chain lubrication the light is on for few kms.
@@halfbikr to avoid this problem. Before running the bike for chain lubrication on 1st gear. Turn off the traction control. This is solve the issue, it's due to the traction control. The sensor is probably confused if the traction control is on and the front wheel is stopped and real wheel is running 😅
Rs. 250 for chain lube? that's too much bro. Bigwing near me charges only Rs.120 and they are very friendly too.
Ohhh damn. Which city are you from?
@@halfbikr BigWing Saharanpur (Uttar Pradesh). Also, I guess rates varies according to different cities. In Delhi it is nealy Rs.200, in Coimbatore it is around Rs. 150. It should be same across all showrooms. One of my friend in Delhi was charged Rs. 1800 for 1st service but I was charged Rs. 1450 then I sent my bill to him and he got refund after a week.
Something to be concerned about. 😳
😂@@halfbikr
Bro i have a doubt
Yes bro tell me
@@halfbikr tamil tha bro
Ungala contact epadi bro panurathu
Nanu cb rs tha varuchuke iniki engine light glow aga aramichu but bike vangi 4 months tha aguthu...
Find me on Instagram. @halfbikr
Bro console use pathi oru kutty video
Potrukene bro.
th-cam.com/video/gVmBteJugWw/w-d-xo.html
Edhathu specific ah venuma solunga bro
என்ன சார் saree guard கழட்டாமியே 3000 km ஓட்டிட்டீங்களே
Aama sir. Dho ipo nalla veyil adika arambichurchula .. saree guard mudguard elathyu kalatira vendi dhaan
Halfbiker also half knowledge
Yen sar 🥹