Simply one of the best educational videos on TH-cam with very clear explanation anyone can understand. Really good professional, and an excellent teacher. Thanks Doc!
I loved how the way you exlpaned to us on how to renistall a head gasket seal on this corolla engine. Can you please make more videos like this. Thanks.
Hey Peter, thank you for your awesome video. I just replaced my head gasket this week also. But I noticed the new head gasket is missing a coulant hole closed to timing chain area, lower left. Is that going to cause a heating problem, or was that a design fix from toyota?
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket between the cylinders. When I looked down the cylinders and saw no cross hatching, do I need to hone them? Can I hone without taking out the pistons? I wasn't burning oil. Thanks
Peter your video was very informing. I would like your advice. I had an overheating issue and i replaced my thermostat and then everything ok till now. My coolant is running low iam missing 300 ml in 200 km. Could it be a bad radiator cap or a bad head gasket? Also i placed my hand on the exhaust pipe and there was steam. Is it normal?
Hay, i broke my spark plugs wrench (key) inside the tube how can i take it out My engine looks similar to this one The spark plugs tube like this one in the video
Your sequence of head bolt removal is different from toyota manual. Not sure if it's significant, but they have specific sequence in which head bolts should be removed.
Hi peter, my head gas kit has been burned and now machanic is asking to change it. I need to confirm if i need to fully change the assembly or only gasket. As in Pakistan i heard vitz piston are available but can not fit as original. Please advise.
Hi Peter. I have a E110 Corolla wagon and my rear smog light isn't working. The fuse is good, the bulb is fine and the switch and relay is working also. I think that there is no power coming to a connector for the bulb. Any ideas what could cause this problem. Terve Peter. Minulla on E110 Corolla wagon. Takasumuvalo ei toimi. Sulake, kytin, rele ja polttimo ovat kunnossa. Polttimon liittimelle ei tule jännitettä mikäli olen mitannut oikein. Veikkaisin että johdot ovat poikki jostain. Mitään ajatusta, että mistä kannattaisi katsoa? Kiitos.
The timing chain marks when they line up on the 1NR-FE will be at 12 o'clock on both camshafts. You can't miss it because both coloured links on the timing chain and the little holes on the camshaft timing gear will be centred at the noon position ( I presume you're talking about setting cylinder one to top dead centre, compression stroke).
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket between the cylinders. When I looked down the cylinders and saw no cross hatching, do I need to hone them? Can I hone without taking out the pistons? I wasn't burning oil. Thanks
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket between the cylinders. When I looked down the cylinders and saw no cross hatching, do I need to hone them? Can I hone without taking out the pistons? I wasn't burning oil. Thanks
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket between the cylinders. When I looked down the cylinders and saw no cross hatching, do I need to hone them? Can I hone without taking out the pistons? I wasn't burning oil. Thanks
![โอ้เธอช่าง... - บี้เดอะสกา ft. ต๋อง เทวัญ (Prod. by ป๋าเพชร) [Official MV]](http://i.ytimg.com/vi/zbWhiLFmVL0/mqdefault.jpg)
Simply one of the best educational videos on TH-cam with very clear explanation anyone can understand. Really good professional, and an excellent teacher. Thanks Doc!
Wow, thanks!
I loved how the way you exlpaned to us on how to renistall a head gasket seal on this corolla engine. Can you please make more videos like this. Thanks.
👍
Hey Peter, thank you for your awesome video. I just replaced my head gasket this week also. But I noticed the new head gasket is missing a coulant hole closed to timing chain area, lower left. Is that going to cause a heating problem, or was that a design fix from toyota?
Yes it will
Did you have overheating ssues with tbis car because the gasket and cylinder head I have are the same , just the one in your video?.
agree, but if it broke in the first place the original can't be too good to begin with.
Noted 👍
Useful imformation Peter!
Thanks again. :-)
Every time I search my car problem, I see peter show up.
Good comment and Thanks ! 😀👍
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket
between the cylinders. When I looked down the cylinders and saw no cross
hatching, do I need to hone them? Can I hone without taking out the
pistons? I wasn't burning oil. Thanks
Peter your video was very informing. I would like your advice. I had an overheating issue and i replaced my thermostat and then everything ok till now. My coolant is running low iam missing 300 ml in 200 km. Could it be a bad radiator cap or a bad head gasket? Also i placed my hand on the exhaust pipe and there was steam. Is it normal?
what about the smoke coming out from the exhaust pipe is it white ?? if yes then your gasket is blown if not check your waterpump
@@ironpatriot6053 its not white. I just refill my radiator with coolant for the meanwhile
@@Gijerboo ok ... check if there's any leak in your radiator or check the engine oil level and the color too !
Ok and Thanks 👍
Hi is it safe to add additives to the engine to stop cylinderhead gasket for leaks
Hay, i broke my spark plugs wrench (key) inside the tube how can i take it out
My engine looks similar to this one
The spark plugs tube like this one in the video
Thanks for comment. 👍😀
Hey peter my Toyota Corolla be throwing a lot of smoke out of the exhaust do you think it’s the head gasket ???
it's probably just running rich
Your sequence of head bolt removal is different from toyota manual. Not sure if it's significant, but they have specific sequence in which head bolts should be removed.
it does matter which order you take them off and put them on
Thanks for comment 😀👍
Thanks my friend i am Muammar from Libya 🌹👍
👍
Is it necessary to remove the engine ?
no
Thank you idol for always sharing your skills,I always following your videos
Always welcome Thanks 👍😀
i realize it's kind of off topic but do anyone know a good place to stream new series online ?
@Simon Gage flixportal xD
@Zakai Benson thanks, signed up and it seems like a nice service :) Appreciate it !!
@Simon Gage no problem =)
Great video
Glad you enjoyed it
@@PeterFinnTheCarDoctor u are just the best but I did not see the video to replace the gasket
Hi peter, my head gas kit has been burned and now machanic is asking to change it. I need to confirm if i need to fully change the assembly or only gasket. As in Pakistan i heard vitz piston are available but can not fit as original. Please advise.
What happened
In this case cylinder head don't need to be resurface?
Yes
Thanx Peter
Right 👍
Hi Peter. I have a E110 Corolla wagon and my rear smog light isn't working. The fuse is good, the bulb is fine and the switch and relay is working also. I think that there is no power coming to a connector for the bulb. Any ideas what could cause this problem. Terve Peter. Minulla on E110 Corolla wagon. Takasumuvalo ei toimi. Sulake, kytin, rele ja polttimo ovat kunnossa. Polttimon liittimelle ei tule jännitettä mikäli olen mitannut oikein. Veikkaisin että johdot ovat poikki jostain. Mitään ajatusta, että mistä kannattaisi katsoa? Kiitos.
Hi, please add new cable and wire
Very helpful information thank you very much God bless you
Glad it was helpful!😃
thanks Peter ...
Thank You Sir. :-)
Please what is the number of the allen key you used to open it?
Noted 👍
Great man I'm from Pakistan
Very good
Thanks 😀👍
U are total outstanding
👍👍👍
Hey do you have a video for 1nr fe timing chain marks?
Thanks for comment. 👍😀
The timing chain marks when they line up on the 1NR-FE will be at 12 o'clock on both camshafts. You can't miss it because both coloured links on the timing chain and the little holes on the camshaft timing gear will be centred at the noon position ( I presume you're talking about setting cylinder one to top dead centre, compression stroke).
Brilliant
Thank You Sir 👍😀
Excellent.
Thanks !
Badass mechanic 👍
No way. Pro man here.
Noniin! Kiitos
You're welcome!👍😃
Thanks😊😊😊😊
No problem 😊
Please speak in hindi language
Thanks! 😃
What's up peter
Great Thanks Sir
dear Peter; you know your stuff but it is very hard to understand you due to your primary language background. Sorry
👍
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket
between the cylinders. When I looked down the cylinders and saw no cross
hatching, do I need to hone them? Can I hone without taking out the
pistons? I wasn't burning oil. Thanks
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket
between the cylinders. When I looked down the cylinders and saw no cross
hatching, do I need to hone them? Can I hone without taking out the
pistons? I wasn't burning oil. Thanks
Hay Peter, I pulled my cylinder head off and found a gap/burn in the gasket
between the cylinders. When I looked down the cylinders and saw no cross
hatching, do I need to hone them? Can I hone without taking out the
pistons? I wasn't burning oil. Thanks