Genuinely thanks. It's been a lot of years I've been looking for someone that could speak. The? Variety. Of senses you use timing and wisdom is everything thank you.❤
@@MacGyverK From my point of view I’m grateful to anyone helping me to resolve a problem, secondly your explanation are well done and help me to resolve my problems easily, and the fact that peoples helps each others no matter the frontiers and the languages barrier add fuel to my optimism toward humanity. So that’s a well deserved thank you , and i think we are in a world where complaints travel faster than gratitude so , it’s normal that i express my gratitude toward your work . Again thank you and have a good day =)
To be honest I wasn't sure exactly what the repair was until I read some of the comments. It is the pin that wears down so won't locate in the locking holes in the shaft. Now I understand and will fix mine. Incidentally, mine is a very old 300 model and it has only just failed. Kind regards Paul from 48 Spokes 🇬🇧
You know the most fustrating thing is it is brand new only used 4 times....and can l say barley regarding those 4 times. Thank you for this tutorial l live on a island we really are not getting any mail at this time so to perhaps buy parts if needed would be at keast 4 to 6 months. Will try this to see if l can get it working again. Can l ask is this common? First the drill bit was stuck but than l remember using it at low speed might cause the bit to come out which it did. Thinking after that l could unscrew it but still no luck cannot get it un-tightened. Does exactly this. 😔 thanks again.
Hoping for help. My Dremel 3000 has this issue where those 2 plastic screws on each side that house a copper spring (I don't know what that is), have a strange issue. The Dremel works only if I press hard on one of them. The moment I release pressure from the screw, it stops. What might be the issue and is there a way I can fix it please? Thank you.
Well explained the condition of your Dremel. I understood. It appears that the "carbon brushes" inside both sides of the Dremel are broken. If you have to press it to make it work, try stretching the copper spring a little. If this does not solve the problem, the carbon brushes may need to be replaced.
Thanks very much! I found out I need a new set of carbon brushes. There wasn't much left and the spring had broken off and interfering with the rotary. So happy with you demonstrating how to take it apart. It desperately needed a good clean, I am ashamed to say lol
I have used my Dremel 5 times or so and I got this problem. Now I don't know if I should send it to the warranty or if I should fix it, maybe losing the 3 year warranty. Yes, in Europe we now have 3 years' warranty.
mine has done the exactly same it is ridiculous for the price you pay for the tool compared to the cheaper one. I have a goaxwe or and it is far superior to dremel and cost less than the dremel flex shaft to buy.
it sucks, i used it three times and already the lock button is not locking so I can't change the bit, returning that piece of garbage anmd buying a chinese clone for 1/3rd the price
This is so terrible and deceitful. You show a closeup of the least important part and not the worn out nub that locks the shaft. The proceed to hid it later when you put in on the table. Filing the nub is a bad idea because you remove more material that is needed to drop into the shaft lock hole.
Reeeeeeeeespect. Out of all the videos I just watched regarding do-it-yourself repairs and maintenance on dremels , yours was by far the most comprehensive and you didn't say a single word as well as the subtitles being in a language i can't read. Yet somehow I pulled more from this video than all the other ding dongs 🙇🏻♂️ with the IQ of a cucumber 🥒 , that I'm not sure if they should legally be allowed to operate even the simplest of power tools. 🫨🙃videos taken upside down, out focus and from twenty yards away...🤦🏻♂️🙄 the only for sure thing that ever enters the frame is their bruised, cut up, burnt and neglected wounds on their hands and fingers. Not instilling much confidence in their competency's. Whenever someone spend# more than two seconds talking about safety glasses and masks, that's usually a good sign anything they have to say about the actual mechanism is not going to be very insightful. People will usually talk first and longest about their erudition on a topic. Ohhhhhhhh!!!! And you're the only one who cut the fu***** sticker down the groove , lol everybody else did a freaking sticker removal tutorial. Is this really a variable for the layman? 🥴"well I took all the screws out but the darn thing just wouldn't open. Probably because mine is made in America, we make the greatest dremels" duuuhhhrrrrrr
![เปิดคำทำนาย นอสตราดามุส - บาบา วานก้า ปี 2025 คนทั่วโลกต้องเจออะไรบ้าง? | แฉ 11 ธ.ค. 67 [2/3] |GMM25](http://i.ytimg.com/vi/xmTIKWJUMPM/mqdefault.jpg)
같은 문제가 있었는데, 드레멜 홈페이지에 sparepart 를 판매하고 있네요.. 5천원에 구매 가능합니다.
찾기가 힘든데.. 좌표좀 찍어주세요~
샤프트 어셈블리 맞나요?
고객센터에서 안내받은 분해도 및 파트넘버 링크입니다.
해당 파트넘버 확인 후, 고객센터에 전화 하셔서 주문방법 문의하시면 업체 전화번호 알려줄거에요(업체 정보는 따로 남기지 않겠습니다.)
안내받은 업체에 전화하시면 주문 가능합니다.
링크는 유튜브에서 삭제하나봐요..??
삭제되네요….
링크는 고객센터에 문의하시면 되겠습니다…
아마 삭제되나 봅니다.. 알려주셔서 감사합니다
수리보다 구매 원하시는 분들에게 도움이 되겠네요^^
Genuinely thanks. It's been a lot of years I've been looking for someone that could speak. The? Variety. Of senses you use timing and wisdom is everything thank you.❤
thank you:)
Deep thank you from France , just a look in the comments seems you are helping the whole world !
I was greatly encouraged by your encouragement. thank you
@@MacGyverK From my point of view I’m grateful to anyone helping me to resolve a problem, secondly your explanation are well done and help me to resolve my problems easily, and the fact that peoples helps each others no matter the frontiers and the languages barrier add fuel to my optimism toward humanity.
So that’s a well deserved thank you , and i think we are in a world where complaints travel faster than gratitude so , it’s normal that i express my gratitude toward your work .
Again thank you and have a good day =)
Thankyou so much for your help , even in a different language to mine I was able to follow your step by step instructions , you are a star 😄
Zeer helder weergegeven stappenplan met oog voor detail! Hulde! Ga even verder uw kanaal 'bestuderen'.
Nice Modification. I hate how wimpy the shaft lock button is on Dremel tools. I love the music and production in this video too! Bravo!!!
Your praise has given me new strength. thank you.
To be honest I wasn't sure exactly what the repair was until I read some of the comments. It is the pin that wears down so won't locate in the locking holes in the shaft.
Now I understand and will fix mine. Incidentally, mine is a very old 300 model and it has only just failed.
Kind regards Paul from 48 Spokes 🇬🇧
Mine only just started playing up too. I've had it for 11 years now and use it a lot.
Muchas gracias
Me salvaste
Excelente explicación
Por suerte pude dar una vuelta al cable y me salvé de soldar
Saludos desde Barcelona
Absolutely fantastic tutorial and demonstration, Very well done !
Thank you. Mine failed after about 20 uses so you saved me throwing it in the bin😮
Really great instructions, thank you.
Thank you very much for this great video because of you I was able to get my Dremel back up and running
Just what i needed! Great job and thanks for sharing!!!
You're welcome. I'm glad it was helpful to you.
You know the most fustrating thing is it is brand new only used 4 times....and can l say barley regarding those 4 times. Thank you for this tutorial l live on a island we really are not getting any mail at this time so to perhaps buy parts if needed would be at keast 4 to 6 months. Will try this to see if l can get it working again. Can l ask is this common? First the drill bit was stuck but than l remember using it at low speed might cause the bit to come out which it did. Thinking after that l could unscrew it but still no luck cannot get it un-tightened. Does exactly this. 😔 thanks again.
It cannot be said that it is common.
4-6 months! It's hopeless.
Please fix it carefully as you see in the video.😅
it is common just look at the views of this video
well done explanation of the sequence! Thanks
Thank you Thank you~
Thank you very much ❤ great instructions
Hoy destape el mío y está muy desgastado, pensé en adaptarle un remache pero no sé si quede
fabulous thats exactly whats wrong with my Dremel will give this a go.. thankyou
Hola, desde Argentina excelente video, muchas gracias
Me sirvió perfectamente.. me salvaste de este problema gracias!!! Muy buen video y muy bien interactuado
Gracias. ¡Tus elogios han sido de gran ayuda para mí!
Excelente trabajo amigo!!! Enorme abrazo desde mi humilde canal Uruguayo.
Gracias. Gracias a ti me fortalezco.
¡¡Muchas gracias por tu ayuda!! Un saludo y mucha salud y fortuna pata ti.
도움이 많이 되었습니다 ㅠ 그냥 취미로 유리 에칭하느라 드레멜 쓰는데 락잠금이 안되어서 식겁했어요 따라서 차근차근 분해하고 말씀해주신대로 갈아서 일단 해결했는데 이거 생긴게 딱… 자주 그럴꺼 같은 소모품이라 벌써 열받네요 ㅎㅎㅎ 영상 감사합니다 ~
잘 해결하셨다니 다행입니다ㅎㅎ 많이 사용하실수록 자주 고장날텐데 어쩔 수 없는 부분인 것 같네요ㅜ 완전 마모될때까지 써야겠죠
Wow this is WhatsApp i looks for , thank TH-cam for sharing 🤩
Very good thanks😊
Thanks for this video 👍👍👍👍
Great video, could not be better. I will use my lathe to repair my pin.
nice. It would be perfect with a shelf:)
You’re awesome! Thank you!
Thanks for this video, it helped me fix mine today 👍🏾👍🏾😎
Hoping for help. My Dremel 3000 has this issue where those 2 plastic screws on each side that house a copper spring (I don't know what that is), have a strange issue. The Dremel works only if I press hard on one of them. The moment I release pressure from the screw, it stops.
What might be the issue and is there a way I can fix it please? Thank you.
Well explained the condition of your Dremel. I understood. It appears that the "carbon brushes" inside both sides of the Dremel are broken. If you have to press it to make it work, try stretching the copper spring a little. If this does not solve the problem, the carbon brushes may need to be replaced.
@@MacGyverK Thank you so much. I'll try stretching the copper spring, and if that doesn't help, I'll order new springs.
hola! que herramienta usas para sacar los tornillos del dremel?
Hola. Es una llave hexagonal.
saludos, gracias por el video
Excellent! It worked thank you!!!!
Thank you😄
how to change bearings on dremel
can you please name the screw driver or allen driver to unscrew the dremel? the regular allen does not open it. thanks.
You will need a hex bit driver to loosen the dremel
Try searching for hex bits.
@@MacGyverK thsnk you very much.
2:27 까지 했는데 꽉 조여져 있어서 콜릿이 안 빠져요 ㅠ
Thank you.
Thank you!!
Thanks very much! I found out I need a new set of carbon brushes. There wasn't much left and the spring had broken off and interfering with the rotary. So happy with you demonstrating how to take it apart. It desperately needed a good clean, I am ashamed to say lol
I'm happy to be of help to you too :) I wish you always good things.
@@MacGyverK Thank you 🙂
Happened to me on my second use. I think I tightened it too much but still extremly flimsy design in my opinion.
Same here. Poor engineering...
I have used my Dremel 5 times or so and I got this problem. Now I don't know if I should send it to the warranty or if I should fix it, maybe losing the 3 year warranty. Yes, in Europe we now have 3 years' warranty.
Mi dremer tiene atorada la caja de bolas delantera,no gira
Nice music!
T15 Torx bit
I dont Know what i did wrong... when i close it, it doesnt rotate anymore 😢
Check whether the power cord and connector are properly inserted. Also, make sure the collet is installed correctlyㅜㅜ
TÜRKÇE ALTYAZI EKLER MİSİNİZ
mine has done the exactly same it is ridiculous for the price you pay for the tool compared to the cheaper one. I have a goaxwe or and it is far superior to dremel and cost less than the dremel flex shaft to buy.
it sucks, i used it three times and already the lock button is not locking so I can't change the bit, returning that piece of garbage anmd buying a chinese clone for 1/3rd the price
This is so terrible and deceitful. You show a closeup of the least important part and not the worn out nub that locks the shaft. The proceed to hid it later when you put in on the table. Filing the nub is a bad idea because you remove more material that is needed to drop into the shaft lock hole.
Thank you for your advice.
No talk No watch
Reeeeeeeeespect. Out of all the videos I just watched regarding do-it-yourself repairs and maintenance on dremels , yours was by far the most comprehensive and you didn't say a single word as well as the subtitles being in a language i can't read. Yet somehow I pulled more from this video than all the other ding dongs 🙇🏻♂️ with the IQ of a cucumber 🥒 , that I'm not sure if they should legally be allowed to operate even the simplest of power tools. 🫨🙃videos taken upside down, out focus and from twenty yards away...🤦🏻♂️🙄 the only for sure thing that ever enters the frame is their bruised, cut up, burnt and neglected wounds on their hands and fingers. Not instilling much confidence in their competency's. Whenever someone spend# more than two seconds talking about safety glasses and masks, that's usually a good sign anything they have to say about the actual mechanism is not going to be very insightful. People will usually talk first and longest about their erudition on a topic.
Ohhhhhhhh!!!! And you're the only one who cut the fu***** sticker down the groove , lol everybody else did a freaking sticker removal tutorial. Is this really a variable for the layman? 🥴"well I took all the screws out but the darn thing just wouldn't open. Probably because mine is made in America, we make the greatest dremels" duuuhhhrrrrrr