The first 3 minutes where you explain Left/Right Bank 1/Bank 2 - YOU are a hero man. So many people don't understand this. My first V6 car was a FWD Mazda 626, and being somewhat dyslexic it took me years to wrap my brain around that.
What a life saver bud ! Just about to take on my first 3.5 v6 timing chain bank 1 cam sensor pickup has broken and I didn’t have any data so thank you 🙏
you shoulf he getting more subs. you’re doing a good job making these videos. i hope you keep doing these. one note though, if my 2gr-fe already out, i would have asked you to change the head gasket as well as the water pump and go on for another 200k miles
The number one idler sprocket you spent time on does go bad especially if a little sludge gets into the oil feed, I would recommend if you go to the trouble of replacing the belts you should really do all bearings now while your there.
I have a 2012 rav4 v6 with 107k miles. Bought it in February with 95k miles. Should I do the transmission flush? When is the spark plus due? Should I be worried about engine/transmission failure? I like watching your video and it’s very educational.
The spark plugs are due at 120k miles. Yes, I would replace the transmission fluid every 60k miles. I wouldn’t be concerned with engine failure because by the year 2012 most of these VVT issues were fixed. They mostly had issues on the earlier years. A lot of these engines have water pump failures which can be a pain to replace but one you replace it, you’re good. The 2GR-FE is pretty much bulletproof. And these Toyota transmissions are some of the best in the world. Just change your ATF every 60k and you should be fine. You chose a good car to buy. Some people say never change your ATF if it’s gone over 100k and never been changed, but I’ve spoken to local transmission rebuilders who say that’s a lie and it needs to be changed. It would be like someone telling you not to change your engine oil. I understand the reasoning why people say don’t change it, but I would still replace it.
This was a very interesting video. I feel like I can try this with someone to overlook what I'm doing. I have a 2016 Pilot, and I just did the timing belt on it, but this Is way more moving parts. Very good job. Thank you for sharing.
Hey Awesome video, I exactly followed & installed the chain. All lined up. Once you do few rounds of hand cranking the crank bolt Is it normal for the primary chain to be at different places ie out of alignment (between the two cam shaft & lower sprocket). Thanks
hi great video. I am in the middle of replacing exhaust cam, however the little clocking nub (dowel pin?) on the camshaft does not fit into the hole of the new gear. I have tried both OEM and rockauto replacements. would I have to buy a whole new camshaft? File down tehe inside hole? kind of at a loss
It should fit when timed correctly, especially if you’re using a Toyota gear. Are you sure you’re lining everything up properly? It will be hard to tell anything without seeing what you’re doing.
Great video with clear presentation. How many miles were on that engine? Were there any noises that pointed to the exhaust VVT gear coming loose and walking towards the timing cover? I have a 2007 Camry with same engine at 250,000 miles. Runs great, no noises, oil changes by me every 5000 miles. Keep the videos coming
It has 132,000 miles. So here’s the thing: the customer towed the vehicle in because the oil cooler lines ruptured. He claims he never heard any weird noises, but when I was disassembling the engine, I noticed that the water pump bearing was so bad that the pulley was about to fall off! There’s no way that wasn’t making noise! The VVT gear wasn’t quite touching on the valve cover yet (I checked and there were no marks on the timing cover). But it would have eventually started touching and making a ticking sound.
I have questions.... How many miles were on this vehicle? And was it making that tell-tale clackity clack of the VVTi pin at cold startups? Our Highlander has been doing that for years... And is that exhaust timing gear with the failed collar ring redesigned? Is the collar connection different? I looked that part up (Toy/Lex - 13080-31030) and noticed it supersedes 2 part numbers. It looks the same though, so I'm just curious if they've devised a better way of assembling the collar part so it doesn't fall apart now.
Hi Jack. I got a 2GR-FE that came out of a Lexus RX350 2007 for a head gasket replacement and exhaust cam gear replacement. Got a brand new exhaust cam gear replacement and after coupling things back with the right valve timing, starting the vehicle there was so much clattering sound within the engine and engine wouldn’t idle again. Brought down engine back and discovered the exhaust cam gear for both banks, the new ones while turning the engine were making a knocking noise. Pulled them off and got a used one from a known good engine. Since then noise continued and engine starts but refuses to idle. Did a compression check on bank2 and had 175, 180 and 185psi respectively on cylinder 2,4 and 6. I watched your video and you spoke about the round o-ring at the engine block which the timing cover protects. Could it be I lost oil pressure somehow. Is there any idea as to what’s going on. Thanks in anticipation
I’m redoing this job after a shop did heads, had timing codes after. I’m finding the guides and main oil pressure oring behind timing cover was not replaced (was it bad shape). Also cam tensioners and chains were reused. Only thing replaced there was main chain, tensioner and center sprocket. So my question is is all this enough to cause timing codes? Also is there a way to check if cam gears are bad, and can they be put on wrong? Had some popping out of intake when turning by hand. Thank you.
BRO - At 15:18 you mention the idler gear and to leave it alone. Dear God no! 😲 DEFINITELY replace that!! That small gear is called the Idler Sprocket Assembly, part # 13530-31021 on both Lexus and Toyota parts sites (common part in the 2GR family in a dozen or more diff Toy/Lex vehicles), and is about $19 before shipping. It'll be prob. $24 MSRP (or higher with markup) at your local greedy Lexus or Toyota dealer - I say greedy as my local Toyota dealer in Hanover, MA is greedy AF when it comes to parts pricing. Also can't hurt to drop another $30 on a new crankshaft timing gear while you're right there - Lex/Toy - 13521-31041. I'm at least glad that at 29:28 you address this gear and discuss the importance of aligning the existing wear marks with the chain. I am not sure you'll have engine timing warnings on the dash but I am 100% certain you'll have the noise problem I brought up. So, that little f**ker is making SO much "winding" noise in my '15 Lexus GS 350 and it's annoying as FK. Lexus already replaced it once under warranty (around 45K miles or so) and it's back to being noisy as hell. The noise started to return within a year, and at 99K miles it's an omnipresent sound I even hear inside the car with the windows up. Our 2008 Toyota Highlander has the same noise from the same exact part in that car's earlier version of the 2GR 3.5 V6. Poor design and I don't trust it's durability, though I can say that the Highlander has made it to 254,000 miles with no timing issues. (knock wood!) But the noise it produces makes the car sound like a shyt box.
hey man i have big questions and i really need help on my 2008 honda accord is there any way i can contact you to get help …im having trouble with the timing on a 2008 honda accord…i know you did a video which i been referring to the whole time but my camshafts pulleys are turning but eventually it stops at a point and resists please help man
Mr. Jack, Have you changed con rod bearings on these 2gr v6 motors? If so and if you know how, can you explain how to purchase an OEM sized bearing for con rods. Apparently there can be different sized bearings from journal to journal and engine to engine straight from the factory. I called the dealer and they told me i needed to look for number stamps on the block and/or number stamps on the bearings themselves. Thx where on the block would the stamps be and how would they be interpreted to be able to order oem sized bearings? Thanks!
I am at the tail end of this job right now but I am second guessing myself as to whether cylinder 1 is at top dead center on the compression stroke- all my cam gear timing marks are lined up, and my yellow chain link is on the crank sprocket tooth will the small timing dot. Would this be possible if cylinder 1 wasn’t on TDC compression stroke? Thanks for any help
In the beginning of this video I show you how to know for sure that you’re on #1 TDC compression stroke using a glove and a long screwdriver. But to answer your question, no, it would not be possible for all the marks to line up if you’re not on #1 TDC compression. So as long as all your marks are good, then you should be fine.
@@jackhfletcher thanks a lot! Yeah I should have paid more attention in that stage- when i was rotating the engine around with my hand, a glove, long screwdriver in cylinder 1 I was feeling the pressure on the exhaust and compression stroke to an extent so I didn’t pay enough mind
Hey man good job. Please can you help with possible solution to a rattling sound on back 1 after i change tensioner and timing chain on a 2gr fe engine on a 2009 es 350. After completing the job the engine rattles and will not stop rattling. Any help will be appreciated, thank you
Did you use OEM parts? That would be my first question. Unfortunately, you’re probably gonna have to pull everything back apart and take a look. If you used OEM parts and it still rattles then something wasn’t installed correctly.
dude i exactly have the same problem, is it rattling at the idler gear in the middle? i had to take everything apart and now just replaced chain, idler gear, and tensioner, putting the case and everything else back together for the 2nd time, @jackhfletcher could i send my timing marks to your email make sure
You turn the engine downward I mean rolling the engine and I can see is not causing anything pictures that the piston is not turning when you rule the engine a little bit confused I do save your videos you're good boss
I changed the exhaust cam gears because they were coming apart as you can see in the video. I decided to change the intake cam gears also because the vehicle was towed into the shop not running, and I didn’t know the history of the vehicle so I wanted to change them to be safe. But no, it’s not necessary unless there is a problem with them.
man after doing this job i didnt set the correct position on the idler gear, now i hear a rattle from it and getting P0017 and misfire codes, gonna have to re do it huh :/
Great video. But the 1 thing i came here for, you skipped. Im going to be getting my block cleaned, and i want to remove my idler spocket. I know the service manual says its only 44ftlbs, but ive tried as hard as i can and it wont budge. Anyone know if its reverse threaded?
The first 3 minutes where you explain Left/Right Bank 1/Bank 2 - YOU are a hero man. So many people don't understand this. My first V6 car was a FWD Mazda 626, and being somewhat dyslexic it took me years to wrap my brain around that.
This is the Best 2Gr video on TH-cam. So stop searching
This is one of the best explanation videos I’ve seen in a while👍
This is actually better explanation than school class
Whatever TH-cam pays you is not enough. Thank you so much for this video.
Great video. Good details. And thank you for adding the torque specs. Keep up the good work.
What a life saver bud ! Just about to take on my first 3.5 v6 timing chain bank 1 cam sensor pickup has broken and I didn’t have any data so thank you 🙏
after watching this tutorial I'm more than confident to do the job myself, many thanks. Awesome Tutorial 💯
Very well made video. You have given me enough confidence to just sell the vehicle if I ever have this issue on my Sienna 🤣
You are good lecture I enjoyed your video great job Sir I wish I was near you
you shoulf he getting more subs. you’re doing a good job making these videos. i hope you keep doing these.
one note though, if my 2gr-fe already out, i would have asked you to change the head gasket as well as the water pump and go on for another 200k miles
The number one idler sprocket you spent time on does go bad especially if a little sludge gets into the oil feed, I would recommend if you go to the trouble of replacing the belts you should really do all bearings now while your there.
Wow Excellent video you explain things very Clearly great video keep up the good work
I have a 2012 rav4 v6 with 107k miles. Bought it in February with 95k miles. Should I do the transmission flush? When is the spark plus due? Should I be worried about engine/transmission failure? I like watching your video and it’s very educational.
The spark plugs are due at 120k miles. Yes, I would replace the transmission fluid every 60k miles. I wouldn’t be concerned with engine failure because by the year 2012 most of these VVT issues were fixed. They mostly had issues on the earlier years. A lot of these engines have water pump failures which can be a pain to replace but one you replace it, you’re good. The 2GR-FE is pretty much bulletproof. And these Toyota transmissions are some of the best in the world. Just change your ATF every 60k and you should be fine. You chose a good car to buy.
Some people say never change your ATF if it’s gone over 100k and never been changed, but I’ve spoken to local transmission rebuilders who say that’s a lie and it needs to be changed. It would be like someone telling you not to change your engine oil. I understand the reasoning why people say don’t change it, but I would still replace it.
@@jackhfletcher thank you for your response. I will change the transmission fluid and plugs.
Best Video ever done on U Tube. Great Job and explanation!!
Litterally the best explanation video. 👍 perfect
Thank you!
This was a very interesting video. I feel like I can try this with someone to overlook what I'm doing. I have a 2016 Pilot, and I just did the timing belt on it, but this Is way more moving parts. Very good job. Thank you for sharing.
Hey Awesome video, I exactly followed & installed the chain. All lined up. Once you do few rounds of hand cranking the crank bolt Is it normal for the primary chain to be at different places ie out of alignment (between the two cam shaft & lower sprocket). Thanks
So the client agreed to spending 2000$ on vvt gears ???😮
This some car care nut skills you have sir 🎉
Thanks
If you're trying to find TDC and don't have a long screwdriver you could also use the oil dipstick
You are doing a great job sir
hi great video. I am in the middle of replacing exhaust cam, however the little clocking nub (dowel pin?) on the camshaft does not fit into the hole of the new gear. I have tried both OEM and rockauto replacements. would I have to buy a whole new camshaft? File down tehe inside hole? kind of at a loss
It should fit when timed correctly, especially if you’re using a Toyota gear. Are you sure you’re lining everything up properly? It will be hard to tell anything without seeing what you’re doing.
Good explication .good job
Thanks!
Thank you. Just in time. I got to do my aunts Lexus is250 next week. Blown head gasket.
Oooh that’s a fun one!
did u get it
Great video with clear presentation. How many miles were on that engine? Were there any noises that pointed to the exhaust VVT gear coming loose and walking towards the timing cover? I have a 2007 Camry with same engine at 250,000 miles. Runs great, no noises, oil changes by me every 5000 miles.
Keep the videos coming
It has 132,000 miles. So here’s the thing: the customer towed the vehicle in because the oil cooler lines ruptured. He claims he never heard any weird noises, but when I was disassembling the engine, I noticed that the water pump bearing was so bad that the pulley was about to fall off! There’s no way that wasn’t making noise! The VVT gear wasn’t quite touching on the valve cover yet (I checked and there were no marks on the timing cover). But it would have eventually started touching and making a ticking sound.
You are great for explication may be i need this job and i try it with my father 😊
Thank you so much for the video. You're indeed a good man. I love your video so much. 👍
Thanks for watching! I’m glad you liked it!
Very informative video. Thanks
I have questions.... How many miles were on this vehicle? And was it making that tell-tale clackity clack of the VVTi pin at cold startups? Our Highlander has been doing that for years... And is that exhaust timing gear with the failed collar ring redesigned? Is the collar connection different? I looked that part up (Toy/Lex - 13080-31030) and noticed it supersedes 2 part numbers. It looks the same though, so I'm just curious if they've devised a better way of assembling the collar part so it doesn't fall apart now.
it's really explainable.i love diz video.😊
Thanks!! For share the knowledge
Hi Jack. I got a 2GR-FE that came out of a Lexus RX350 2007 for a head gasket replacement and exhaust cam gear replacement. Got a brand new exhaust cam gear replacement and after coupling things back with the right valve timing, starting the vehicle there was so much clattering sound within the engine and engine wouldn’t idle again. Brought down engine back and discovered the exhaust cam gear for both banks, the new ones while turning the engine were making a knocking noise. Pulled them off and got a used one from a known good engine. Since then noise continued and engine starts but refuses to idle. Did a compression check on bank2 and had 175, 180 and 185psi respectively on cylinder 2,4 and 6. I watched your video and you spoke about the round o-ring at the engine block which the timing cover protects. Could it be I lost oil pressure somehow. Is there any idea as to what’s going on. Thanks in anticipation
Great video! Where did you get the parts from ? OEM or aftermarket online ?
I got the parts directly from our local Toyota dealership.
I really love the explanation
thanks for sharing the video.is it possibility doing this job with engine in the car?
No, you have to remove the engine.
I’m redoing this job after a shop did heads, had timing codes after. I’m finding the guides and main oil pressure oring behind timing cover was not replaced (was it bad shape). Also cam tensioners and chains were reused. Only thing replaced there was main chain, tensioner and center sprocket. So my question is is all this enough to cause timing codes? Also is there a way to check if cam gears are bad, and can they be put on wrong? Had some popping out of intake when turning by hand. Thank you.
Nice work and I have add another experience
Is it possible to replace the tensioner on bank 1 without dropping the entire engine, from the top of the valve covers
I need to replace bank 1 exhaust cam gears. Is that doable in a home garage, or does the engine need to be taken out
BRO - At 15:18 you mention the idler gear and to leave it alone. Dear God no! 😲 DEFINITELY replace that!! That small gear is called the Idler Sprocket Assembly, part # 13530-31021 on both Lexus and Toyota parts sites (common part in the 2GR family in a dozen or more diff Toy/Lex vehicles), and is about $19 before shipping. It'll be prob. $24 MSRP (or higher with markup) at your local greedy Lexus or Toyota dealer - I say greedy as my local Toyota dealer in Hanover, MA is greedy AF when it comes to parts pricing. Also can't hurt to drop another $30 on a new crankshaft timing gear while you're right there - Lex/Toy - 13521-31041. I'm at least glad that at 29:28 you address this gear and discuss the importance of aligning the existing wear marks with the chain. I am not sure you'll have engine timing warnings on the dash but I am 100% certain you'll have the noise problem I brought up.
So, that little f**ker is making SO much "winding" noise in my '15 Lexus GS 350 and it's annoying as FK. Lexus already replaced it once under warranty (around 45K miles or so) and it's back to being noisy as hell. The noise started to return within a year, and at 99K miles it's an omnipresent sound I even hear inside the car with the windows up. Our 2008 Toyota Highlander has the same noise from the same exact part in that car's earlier version of the 2GR 3.5 V6. Poor design and I don't trust it's durability, though I can say that the Highlander has made it to 254,000 miles with no timing issues. (knock wood!) But the noise it produces makes the car sound like a shyt box.
Good teacher ❤ explanation
Good job , I lean from it
I love your work, and I will like to know more from you
bro thanks for video. can you tell me what spec torque for upper oil pan please )
The best. Thank you so much.
My engine rattles for a few seconds on cold starts and throughs random misfire codes. How much does the job like that cost?
Do you have to put all the slack on the left ?
Wow thanks have really got a lot
Great teaching
Very good video 😊
Nice job good explanation 👍
approximately how many hours did the job take?
how much for it
Chnaged my timing chain and now i got a low oil pressure on my dash any idea what it is?
What if i got a little slack on the left and right side of the idler gear?
How to replace timing chain Toyota Tacoma 2009 v6 -4.0 and timing chain cover bolts torque diagram
How much did the labor for that cost ?
Good job.
God bless you brother.
hey man i have big questions and i really need help on my 2008 honda accord is there any way i can contact you to get help …im having trouble with the timing on a 2008 honda accord…i know you did a video which i been referring to the whole time but my camshafts pulleys are turning but eventually it stops at a point and resists please help man
Send me an email to doctorjfletcher@gmail.com
and in the email give me your name and number and I’ll call you tomorrow.
Mr. Jack, Have you changed con rod bearings on these 2gr v6 motors? If so and if you know how, can you explain how to purchase an OEM sized bearing for con rods. Apparently there can be different sized bearings from journal to journal and engine to engine straight from the factory. I called the dealer and they told me i needed to look for number stamps on the block and/or number stamps on the bearings themselves. Thx where on the block would the stamps be and how would they be interpreted to be able to order oem sized bearings? Thanks!
I’ll be honest, I’ve never changed bearings on this motor and I really wouldn’t know how to help you with that. Sorry!
Pull a bearing cap and check they will either be standard or oversize they should be marked as such and have a part number
I am at the tail end of this job right now but I am second guessing myself as to whether cylinder 1 is at top dead center on the compression stroke- all my cam gear timing marks are lined up, and my yellow chain link is on the crank sprocket tooth will the small timing dot. Would this be possible if cylinder 1 wasn’t on TDC compression stroke? Thanks for any help
In the beginning of this video I show you how to know for sure that you’re on #1 TDC compression stroke using a glove and a long screwdriver. But to answer your question, no, it would not be possible for all the marks to line up if you’re not on #1 TDC compression. So as long as all your marks are good, then you should be fine.
@@jackhfletcher thanks a lot! Yeah I should have paid more attention in that stage- when i was rotating the engine around with my hand, a glove, long screwdriver in cylinder 1 I was feeling the pressure on the exhaust and compression stroke to an extent so I didn’t pay enough mind
Have good experience and knowledge ❤ like it ❤
same for 2grfks?
Hey man good job.
Please can you help with possible solution to a rattling sound on back 1 after i change tensioner and timing chain on a 2gr fe engine on a 2009 es 350.
After completing the job the engine rattles and will not stop rattling.
Any help will be appreciated, thank you
Did you use OEM parts? That would be my first question. Unfortunately, you’re probably gonna have to pull everything back apart and take a look. If you used OEM parts and it still rattles then something wasn’t installed correctly.
dude i exactly have the same problem, is it rattling at the idler gear in the middle? i had to take everything apart and now just replaced chain, idler gear, and tensioner, putting the case and everything else back together for the 2nd time, @jackhfletcher could i send my timing marks to your email make sure
Very detailed
I learn more🤝🤝
Where did you get the vvt gears from ?
I got them from my local Toyota dealership.
You turn the engine downward I mean rolling the engine and I can see is not causing anything pictures that the piston is not turning when you rule the engine a little bit confused I do save your videos you're good boss
Good evening
How to timing fourtener Toyota engine
ما السبب تتبديل cam gear ،هل هناك ضرورة؟
I changed the exhaust cam gears because they were coming apart as you can see in the video. I decided to change the intake cam gears also because the vehicle was towed into the shop not running, and I didn’t know the history of the vehicle so I wanted to change them to be safe. But no, it’s not necessary unless there is a problem with them.
you are really good sir
Thank you very much
How can I get your contact because I have many question to ask please
where are you located
Katy, TX
man after doing this job i didnt set the correct position on the idler gear, now i hear a rattle from it and getting P0017 and misfire codes, gonna have to re do it huh :/
Man, that sucks! Yeah, you’re gonna have to go back in there and double check your work.
Great video. But the 1 thing i came here for, you skipped. Im going to be getting my block cleaned, and i want to remove my idler spocket. I know the service manual says its only 44ftlbs, but ive tried as hard as i can and it wont budge. Anyone know if its reverse threaded?
Awh man! Now I wish I would have shown it. That bolt is regular thread (right hand thread). Put a long breaker bar on it and it should break loose.
عمل جيد
Now doa a Nissan!
I have that eng…😢DAMN TOYOTAA???😡
😢.
спасибо большое за грамотное видео! очень благодарен за подробное описание технологии замены грм!
I love your work, and I will like to know more from you