You have been a life saver both of these videos have helped me keep peace of mind in installing my flywheel, clutch plate and pressure plate. No where else internet wide has been able to help me as much as these videos😅
Hello sir , did the transmission go all the way on the motor without any pressure resisting it once the spine shaft was aligned to the clutch. I am having a problem with my transmission not resisting me about a half of inch on the motor once I try to install it. Thank You
Did u get it on?? I called it a day. 2 hours trying to line it up today. It was always off just a bit and a half inch gap between the tranny and engine
Hello, I just replaced the clutch and flywheel on an 08 Altima 2.8 s. While I got the input shaft into the pilot bearing, I can't get the two dowel pins on the bellhousing into the appropriate holes on the engine block. Does that mean I did something wrong on the install?
Maybe this helps someone else. I had the same issue. I had to sand down the dowel pins on the engine block to get them to seat. I also used an engine support bar to line it up right. Wasn’t working well with a transmission jack as I’ve done with other vehicles.
Did u have trouble getting the tranny to line back up on the motor?? I got everything replaced. And the damn transmission does not wanna line up, doll pins don't wanna line up and go in. Got about a half of a inch gap. 2 hours now trying to just get the tranny seated onto the engine.
I just did the same job to my '08. Now I can't get it to go into reverse. Any idea what I didn't do. It's seems like it's going into 3rd, 4th, 5th and 6th. It's seems like I'm getting into 1st and 2nd week I pull up the reverse trigger thing but it won't go into reverse.
@Matthew Williams Yes. I forgot to connect the cable the engages reverse. So the two shift linkages I guess you would call them. On the transmission, one shifts gears and the other engages reverse.
@@oneshawnsay mine is connected and is connected on shifter side as well. But some how some way reverse is forward/1st and 1st seems to be 3rd or who knows what gear.
@@partsshooter its about the topic of the clutch driving fine one day then wont start got to put in neutral for the motor to even turn over mine is a 08 6 speed? Thoughts?
2008 just did this and for some reason cannot go into reverse or 1st anymore... Any thoughts on this? did exactly what you have done in videos but obviously something i am missing and can't figure it out.
You have been a life saver both of these videos have helped me keep peace of mind in installing my flywheel, clutch plate and pressure plate. No where else internet wide has been able to help me as much as these videos😅
Doing this now in 2023 on an 09, thank you for this.
whats torque clutch,pressure plate on 2008 3.5 6cilynder nissan altima manual trans mission
Hello sir , did the transmission go all the way on the motor without any pressure resisting it once the spine shaft was aligned to the clutch. I am having a problem with my transmission not resisting me about a half of inch on the motor once I try to install it. Thank You
Having same problem right now
Did u get it on?? I called it a day. 2 hours trying to line it up today. It was always off just a bit and a half inch gap between the tranny and engine
Hello, I just replaced the clutch and flywheel on an 08 Altima 2.8 s. While I got the input shaft into the pilot bearing, I can't get the two dowel pins on the bellhousing into the appropriate holes on the engine block. Does that mean I did something wrong on the install?
Make sure you used a clutch alignment tool and there's nothing around the bell housing during installation.
Maybe this helps someone else. I had the same issue. I had to sand down the dowel pins on the engine block to get them to seat. I also used an engine support bar to line it up right. Wasn’t working well with a transmission jack as I’ve done with other vehicles.
Did u have trouble getting the tranny to line back up on the motor?? I got everything replaced. And the damn transmission does not wanna line up, doll pins don't wanna line up and go in. Got about a half of a inch gap. 2 hours now trying to just get the tranny seated onto the engine.
I just did the same job to my '08. Now I can't get it to go into reverse. Any idea what I didn't do. It's seems like it's going into 3rd, 4th, 5th and 6th. It's seems like I'm getting into 1st and 2nd week I pull up the reverse trigger thing but it won't go into reverse.
Were you able to figure out the issue? i now have this same issue.
@Matthew Williams Yes. I forgot to connect the cable the engages reverse. So the two shift linkages I guess you would call them. On the transmission, one shifts gears and the other engages reverse.
@@oneshawnsay mine is connected and is connected on shifter side as well. But some how some way reverse is forward/1st and 1st seems to be 3rd or who knows what gear.
whats the torque on clutck bolts?
Brother how’d you get the flywheel to stop turning in the wrong direction ? Breaker bar on the crankshaft bolt ?
Lock the the crank shaft pulley with a breaker bar... It'll work just fine
customhonda thank you brother I appreciate the help! Just changed the clutch master cylinder on my 3.5 Altima coupe. Your video was very helpful.
Hey man, what did you torque the bolts down to for the fly wheel and clutch
One last question. What did you use to hold the trans up 2 jacks or a transmission jack ?
Ratchet straps... Looped it around the subframe and back to the transmission.
customhonda thank you! I appreciate it going to tackle my slave cylinder this Friday just got it in the mail.
My Clutch Just Went Out On Me, I Plan To Order a Kit and Do it myself, I only have basic tools, what can i use for impact guns?
i also dont have any Torch Wrenches
Project farm on youtube has a really good video on various impact guns! Id check that out if i was you
@@partsshooter what sizes did you use? to get the trans bolts out and clutch plate bolts?
@@partsshooter and also can you make a list if every single tool you used?
Do you know this motor well ? I have a issue can't figure out lmk
I only be addressing comments related to video topic to aid in helping others. Thanks
@@partsshooter its about the topic of the clutch driving fine one day then wont start got to put in neutral for the motor to even turn over mine is a 08 6 speed? Thoughts?
@@mikehaun6411 is this an automatic transmission you're referring to?
@@partsshooter 6 speed manual 3.5l coupe
@@partsshooter they are rare in the 6speed and alot of people dont know what the deal is hoping you would
2008 just did this and for some reason cannot go into reverse or 1st anymore... Any thoughts on this? did exactly what you have done in videos but obviously something i am missing and can't figure it out.
its like reverse is 1st and 1st is 2nd.
Whats your # I have the same Altima and the same problem
whats your #?
Hi, do you wish to sell your alignment tool? Thanks. @customhonda