.. Ryt then.. This valve opens and pushes into this one, this popper opens and pushes into the big one which pushes a lever into the small one then the initial boost is multiplied by the quad-core processor on the small one which then adjusts the big one which is crucial hsnnsnjdjhdbdbdbbbxnxjxjxjnaakaksjsnnsndjs..... But in the end we making more power!! I'm sold by the last two words. 🤣💪
The amount of metal grid is perfectly normal. Have changed the oil on 5 pcs 313 TDI and they were all full of metal grid on the magnets. Oil change was from 120.000 to 180.000km. Cheers from Denmark. Btw nice project 👌
@@DarksideDevelopments Yeah agree, disappointing result but at least we have some honest numbers finally, would you ever look at doing a single turbo conversion?
mines doing 380hp on stock turbos,no dpf and has to be capped there as egt's need to be kept to safe level..theres no chance of getting anywhere near 450hp stock. Fantasy figures.
Could a similar setup to that be put on a standard 3.0TDI if the bitdi power and torque were sought-after? I'm not apposed to making that bypass valve being mechanically controlled.
We do have turbos for the 3.0tdi that do similar power figures. Drop us an email to sales@darksidedevelopments.co.uk with your reg/vin and we can give you a list of what we can do
Why you dont add big turbo and wastegate to the gtd28? And make true compound? You need boost if you want more power. Compounding is easy way to get that boost up
Thanks for the video, I’ve got one of these and have been following with interest. A couple of questions, what was the verdict on the gearbox after the flush? And, how much power can these gearboxes take? Cheers and keep up the good work.
@@DarksideDevelopments Sounds reasonable. Do you think it would plug the DPF faster or more often since you'd be using more fuel and air? Alternatively, are there bigger DPFs available?
With the right tuning we wouldn't expect the DPF to block or the regeneration being active more frequently. There's very little room to fit anything else on these!
That valve thing u showed at the start of putting back turbo sounds like what my noise is through the air filter box when I’m stationary and I select a gear , is it a characteristic of the car and nothing to worry about ?
Hi guys, after 3 years of being desperate, I understood that 8HP (AL551) can be adapted for higher torque. I had engine swap (CGQB->CVUB) due to burned piston and the new engine is from facelift, but I was promised it was 100% same. Well since then the E clutch adaptation always ends up at -700mbar and that causes slight jerk on 1-2 and 5-6. More pressure to avoid slipping, however damages the E clutch I guess. That engine is puttin out more torque as the TCU is expecting, or at least TCU thinks it is more torque, because the dyno says 570Nm anyway. I have the 8HP55 transmission, but will try to update the AL551 TCU with facelift 8HP70 tranny software to see if it helps or not :-/ No one was able to help me for years with this. Do you think this jerk shifting due to -700mbar fill pressure (-300 to 300 is limit) could be fixed by doing a TCU tune? Did you do the TCU tune in case of your beautiful BiTDI? Thanks!!!
@@DarksideDevelopments thanks for taking the time to reply to me,i take it they are pretty reliable? anything i need to look out for? looking at a 2017/2018 model
@@DarksideDevelopments i have seen quite a lot 550d´s with over 500 HP with stage 2 and there are a view 335d with bold on's with around 500 hp. There are even a view turbo manufactures like turbosystems selling turbos for the n57n for 490+ or M57D30TÜ2 for 500 hp. But i have not seen someone selling a whole kit for such power figures.
As explained in the video far too expensive to justify, same with the 335d, just map and forget about it. But for 3.0 TDI and 330d going for a bigger turbo setup is fine.
@@ThenameisOskar 380-410 max, there is one running over 500 bhp full vehicle weight but I'm not sure of the turbo setup. 1/4 in 11.3s and 100-200 in 7.2s.
So I've walked 5 miles this morning, just finished fixing my car, and then had a shower in a satisfied mood. I feel content whilst ready for lunch in an hour. Switch on youtube to find Ryan coming through like a boss with the Sunday Funday content. Legend. I can retire after this lol
Another really informative vid🙌🙌love the way your totally honest about products 👍👍most company’s would be spurting-out massive power gains just to sell them 👍😉good stuff keep it up 🙌🙌🙌
please make a propper sound video of it 😅 with different exhaust options... original exhaust with your Downpipes (with and without active sound)... complete Straightpiped from turbo back... and maybe a valved exhaust? i'll try to fit a used rs6 exhaust on it with a working valve module to have it loud when i want to 😉👌🏼
Hell yeh. Tho i dont think the y pipe on the bottom of your sti intercooler is any easier to wrangle. The most complicated turbo ive replaced so far was on a 5 cyl turbo fiat. Just abysmal.
It wont, however we do offer a Q7 turbo kit here - www.darksidedevelopments.co.uk/products/audi-q7-4-2-v8-btr-500hp-turbo-upgrade-kit.html Best thing to do is drop us an email to sales@darksidedevelopments.co.uk with your reg/vin number to make sure the parts match up or see if we can offer any other alternatives
@@ThenameisOskar I assume you mean my diesel and not my race car. No, I've since installed oem dpf and a trailer hitch so mine definitely won't be as fast anymore. But I'll have a go when my summer tires are back on for shits and giggles. Also, mine is a wagon. 2t +
Is this all with a standard air intake and filter setup? I've read it's decent with no mods. I saw you were experimenting with putting an RS6 style vent in the air box. How did that go?
Thanks for replying. I guess it allows a little more air in and smooths the flow. Is it something you'll retail? Great content and explanations on all you content 👍🏼
Definitely not worth the investment unless you are replacing the turbos anyway. On the old m57 335d's you can now fit hybrids that will take you to around 500 or more bhp.
@@DarksideDevelopments true, seen several printouts but they may be of the inflates kind.. There is always the option of fitting a 3rd bigger turbo like santjer performance did in the US, over 600whp, check their Facebook page, 5.3s 100-200kph diesel only.
When I have done the trans is the past I disconnected one of the cooler lines and once I had refilled the system I ran it to pump a litre or so out from the cooler line. I then topped up and repeated until I got clean oil. This pushes the dirty oil out that sits in the torque converter.
my bitdi gearbox was nearly the same at 65k miles (slightly less ferreous on the filter magnets). only strange things i have are clunky changes when cold into first gear. im now changing oil (roughly 4 litres) every year/10kmiles and this keeps the gear changes good. if i dont the clunking comes back. only changed the filter once at 65kmiles. oil comes out mucky every time. mine is mapped to 390hp and runs extremely hot over 4krpm, so i short shift. should really have it remapped to a safe egt limit. your turbo set up has a decent rise across the whole usable rev range, but as you say its going to be expensive for a relatively small gain. bring on the big turbo!! will the gearbox handle 1000nm?? and have your gearbox maps tightened up the first 3 gears? keep it coming! :)
Nice videos! You won’t get more oil than that from the transmission from just a drain as the torque converter will hold a few litres, but that’s the correct procedure anyway flushing is not really recommended. Also the noise you have is more likely to be the chain/tensioner, very common on these! Look forward to see’ing more developments 👍🏼
Not sure if you’re saying its ZF procedure to flush? But it’s not ZF procedure to flush using a machine, this can potentially cause issues. ZF procedure is simply to drain (at correct temps) and refill, to achieve a better/complete oil change you could repeat this process again after a shorter period of time 👍🏼
is there a difference in the 3.0 tdi engine and the 3.0 bitdi ? can a c7 a6 3.0 tdi be converted to a 3.0 bitdi without major work ? amazing channel btw !
@@DarksideDevelopments what single turbo would u reccomend for it ? Can we push 400bhp and 1000nm crank, with other supporting mods like IC, fuel pump etc ? Sorry I'm a noob
@@DarksideDevelopments i didnt mean to be disrespectful i like how you tune diesels, what do you mean by that not on our dyno, is possible some companies could present figures more “optimistically”?
Yes glad we got an update but I’m sure he had it to Audi no so long before he sold it to you for a service and I’m sure there’s a abart 2 years Audi service plan left on it too I do t know how it works with it been tuned now but when he bought it nearly 3 years to the day the original owner bought a 5 year Audi plan just before he sold it lads
I wouldn’t be sending it back either with 5 litre of oil being init be I’m more than certain it was done only a few month before you got it but he had a a4 3.0 tdi before the bi and he asked about having Torsen done on that and they said they can’t do it and couldn’t be done literally drove to vw and they did it for him so just shows what theses all singing all dancing warranty’s and service plans a worth dunit
Lol, and when the electric goes off what you going to do? Please don't buy online either, a diesel ship brings it to a diesel truck and a diesel van delivers it. Small minded sheep walking to the slaughter house...
@@DarksideDevelopments oh the naivety, fella are you not following the new car scene, all the latest and best stuff is either hybrid or fully electric, do you realise how hard it will be to get a diesel vehicle through emissions in the next few years, it will be next to impossible, governments are under severe pressure to rid their country’s of nox particles in the atmosphere,
Reyt then
.. Ryt then.. This valve opens and pushes into this one, this popper opens and pushes into the big one which pushes a lever into the small one then the initial boost is multiplied by the quad-core processor on the small one which then adjusts the big one which is crucial hsnnsnjdjhdbdbdbbbxnxjxjxjnaakaksjsnnsndjs..... But in the end we making more power!!
I'm sold by the last two words. 🤣💪
Bi turbos witch operate in series and parallel are an ass to tune. But when you get it right it's absolute magic
Loving the frequent and HIGH-quality videos chaps!
The amount of metal grid is perfectly normal. Have changed the oil on 5 pcs 313 TDI and they were all full of metal grid on the magnets. Oil change was from 120.000 to 180.000km. Cheers from Denmark. Btw nice project 👌
Can you do some 100 - 200 km/h runs with this setup? Would be nice to see how this compares to the so called 450hp+ BiTDI's on stock turbo's.
That's the plan when the roads are good.
@@DarksideDevelopments Yeah agree, disappointing result but at least we have some honest numbers finally, would you ever look at doing a single turbo conversion?
lol 450hp on the stock setup is dreaming eh. dyno power factor fudging....
mines doing 380hp on stock turbos,no dpf and has to be capped there as egt's need to be kept to safe level..theres no chance of getting anywhere near 450hp stock. Fantasy figures.
@@Spannerface same on mine mate.
Thank you for this update, very interesting.
Cannot wait to see the end result
Them boxs never drain full amount, when you strip them to repair you always get another few litres out on the bench.
Could a similar setup to that be put on a standard 3.0TDI if the bitdi power and torque were sought-after? I'm not apposed to making that bypass valve being mechanically controlled.
We do have turbos for the 3.0tdi that do similar power figures. Drop us an email to sales@darksidedevelopments.co.uk with your reg/vin and we can give you a list of what we can do
wow Ryan that's huge! 😂👍🏼
Have you considered developing your own hybrid turbo system with electronic valve control? seems like you said that the overlap would be more smooth.
Maybe one day
Why you dont add big turbo and wastegate to the gtd28? And make true compound?
You need boost if you want more power. Compounding is easy way to get that boost up
We might, 28 is too big for HP turbo
@@DarksideDevelopments you just need a properly sized LP turbo and it will be 👌🏻
Just seen you at TCPerformance. Hope you found your way to your lift alright 😂
Haha, she was miles away!
@@DarksideDevelopments oh noo 😂. My mum had the same problem. I ended up calling her to bring the service booklet down for me 😅
Maths+science = boost
In Romania we succeed to achieve 4xx hp with stock turbos and literally no smoke
Good for those guys!
As always, damned interesting! 😄
Isn’t some of the oil staying in the torque converter
You might need one of them flushing machines👍
Flippin eck
Good honest video's 👌
Very nice,
As an aside, 3.0 liter V6 Touareg, 2012, if you went balls out, bigger turbo, 6 oversize injectors, what could you squeeze out of it?😂
400+
What’s next for the gearbox? If an oil change doesn’t help, rebuild or replace?
Manual swap xd
Thanks for the video, I’ve got one of these and have been following with interest. A couple of questions, what was the verdict on the gearbox after the flush? And, how much power can these gearboxes take? Cheers and keep up the good work.
Gearbox seems fine. I doubt you would break it with power!
After honest opinions here, Im an Audi guy through and through, but how does the Audi 3.0L Diesels compare to the BMW 3.0L diesels for power and mods?
Very similar really
How well would it handle hybrid turbos with the aftertreatment intact? DPF and DOC.
I can't see why not but maximum power might be less
@@DarksideDevelopments Sounds reasonable. Do you think it would plug the DPF faster or more often since you'd be using more fuel and air? Alternatively, are there bigger DPFs available?
Depends how rich the tune is!
With the right tuning we wouldn't expect the DPF to block or the regeneration being active more frequently. There's very little room to fit anything else on these!
That valve thing u showed at the start of putting back turbo sounds like what my noise is through the air filter box when I’m stationary and I select a gear , is it a characteristic of the car and nothing to worry about ?
Our issue was too much boost request at lower RPM and idle
@@DarksideDevelopments as far as I know my car is standard
Are you opening the exhaust change flap before you want the change over
The tuners have experimented with a lot of things!
@@DarksideDevelopments opening the exhaust and slowly shutting down the little turbo
Hi guys, after 3 years of being desperate, I understood that 8HP (AL551) can be adapted for higher torque. I had engine swap (CGQB->CVUB) due to burned piston and the new engine is from facelift, but I was promised it was 100% same. Well since then the E clutch adaptation always ends up at -700mbar and that causes slight jerk on 1-2 and 5-6. More pressure to avoid slipping, however damages the E clutch I guess. That engine is puttin out more torque as the TCU is expecting, or at least TCU thinks it is more torque, because the dyno says 570Nm anyway. I have the 8HP55 transmission, but will try to update the AL551 TCU with facelift 8HP70 tranny software to see if it helps or not :-/ No one was able to help me for years with this. Do you think this jerk shifting due to -700mbar fill pressure (-300 to 300 is limit) could be fixed by doing a TCU tune? Did you do the TCU tune in case of your beautiful BiTDI? Thanks!!!
Its hard to say but software would be worth a shot before changing the hardware. Maybe try TVS, these are pretty well known for there DSG software.
@@DarksideDevelopments Thank you, will try to get in touch with them. Best wishes to you!
So there is little one transition to big one ?
Yes
Do they pass mot soot test with dpf delete
Yes, easily
Grate that’s what I wanted to know 🤟🏻 new to the diesel scene been a petrol vager for to long awsum work
Could this setup be used on a 2011 Q7 3.0L US version?
No those are single turbo, email us!
ive been looking at these but as i do short trips i dont want dpf issues, if you delete them does the car smoke alot?
They stink a little from cold but otherwise no smoke
@@DarksideDevelopments thanks for taking the time to reply to me,i take it they are pretty reliable? anything i need to look out for? looking at a 2017/2018 model
Something that new should be fine!
On my bitdi the high pressure turbo is broken.
Faultcode p0299 comes up when i touch the throttle and the rpm passes 2800rpm.
Do you sell turbos?
We have a few new ones and used. Email us with a VIN.
We emailed you but your inbox is full!
Did you receive my VIN? How is it possible that my inbox is full?
@@DarksideDevelopments Try now👍
???
why does Audi seems to be like 100 -150 hp down to 3.0 diesels from BMW ?
I'm not sure where you numbers are from!
@@DarksideDevelopments i have seen quite a lot 550d´s with over 500 HP with stage 2 and there are a view 335d with bold on's with around 500 hp. There are even a view turbo manufactures like turbosystems selling turbos for the n57n for 490+ or M57D30TÜ2 for 500 hp.
But i have not seen someone selling a whole kit for such power figures.
"comment: BIG TURBOS" xD
Moor brek oss.....Be reyt..
Dunt ferget towark
Where can you buy this?
You can't, yet
@@DarksideDevelopments when will it be possible then and in what price range?
Not sure yet!
Reyt then, just gonna get me ears lowered
Jesus that sounds complicated
As explained in the video far too expensive to justify, same with the 335d, just map and forget about it. But for 3.0 TDI and 330d going for a bigger turbo setup is fine.
@@ThenameisOskar 380-410 max, there is one running over 500 bhp full vehicle weight but I'm not sure of the turbo setup. 1/4 in 11.3s and 100-200 in 7.2s.
@@ThenameisOskar Could be dyno variation or the mapping.
@@RealGX that was a polish guy, it was a heavily increased larger turbo and everything else. quick car, but smoky haha
@@GGXjimmy I think the guy in question did put a Custom John Deer hybrid turbo
Poor explanation! Only experts understand what u are talking about!
I bet
So I've walked 5 miles this morning, just finished fixing my car, and then had a shower in a satisfied mood. I feel content whilst ready for lunch in an hour. Switch on youtube to find Ryan coming through like a boss with the Sunday Funday content. Legend. I can retire after this lol
On my bitdi the high pressure turbo is broken.
Faultcode p0299 comes up when i touch the throttle and the rpm passes 2800rpm.
Do you sell turbos?
Yes I emailed you but your inbox was full
Not anymore 😉
If it still doesn’t work, just email me at: Niko8@live.no
I need boooooooost😁
I sent an email
Love how the torque kicks in even earlier.
Must be a hell of a drive but also relaxing too.
Would love to see this get to 440BHP then race against the S6 petrol variant to see how close it would be in a drag race!
i guess Im kinda randomly asking but do anyone know of a good place to watch newly released tv shows online ?
@Deacon Jay flixportal =)
@Justin August thanks, I went there and it seems like they got a lot of movies there :D Appreciate it !
@Deacon Jay no problem :D
Another really informative vid🙌🙌love the way your totally honest about products 👍👍most company’s would be spurting-out massive power gains just to sell them 👍😉good stuff keep it up 🙌🙌🙌
We could sell a lot!
please make a propper sound video of it 😅 with different exhaust options... original exhaust with your Downpipes (with and without active sound)... complete Straightpiped from turbo back... and maybe a valved exhaust? i'll try to fit a used rs6 exhaust on it with a working valve module to have it loud when i want to 😉👌🏼
That turbo arrangment looks very complicated
Hell yeh.
Tho i dont think the y pipe on the bottom of your sti intercooler is any easier to wrangle.
The most complicated turbo ive replaced so far was on a 5 cyl turbo fiat. Just abysmal.
I have a 3.0tdi quattro but with just a single turbo and the 8-speed tiptronic gearbox how feasible would it be to just bolt on the biturbo?
No, it's easier to put 1 big turbo on there anyway!
Can this biturbo works on the audi Q7 2007
It wont, however we do offer a Q7 turbo kit here - www.darksidedevelopments.co.uk/products/audi-q7-4-2-v8-btr-500hp-turbo-upgrade-kit.html
Best thing to do is drop us an email to sales@darksidedevelopments.co.uk with your reg/vin number to make sure the parts match up or see if we can offer any other alternatives
do they make bigger compound set ups like this like in the 500hp range. I'd love to put one on my amrok
I want to make one!
I got a 3.0bitdi. Would be interested in the slightly bigger big turbo setup once mine takes a nose dive
@@ThenameisOskar I assume you mean my diesel and not my race car. No, I've since installed oem dpf and a trailer hitch so mine definitely won't be as fast anymore. But I'll have a go when my summer tires are back on for shits and giggles. Also, mine is a wagon. 2t +
@@ThenameisOskar I'll have a go in April.
Can I get this Turbo in your shop?
Unfortunately not, it didn't quite work the way we wanted and wouldn't have been the best value for money set up for what you gain
Look at that bottom end! That 50+ above idle. Pulling a trailer, that's amazing.
Is this all with a standard air intake and filter setup? I've read it's decent with no mods. I saw you were experimenting with putting an RS6 style vent in the air box. How did that go?
It helps a little, not a lot
Thanks for replying. I guess it allows a little more air in and smooths the flow. Is it something you'll retail?
Great content and explanations on all you content 👍🏼
we might sell them eventually!!
Definitely not worth the investment unless you are replacing the turbos anyway. On the old m57 335d's you can now fit hybrids that will take you to around 500 or more bhp.
If you believe those figures...
@@DarksideDevelopments true, seen several printouts but they may be of the inflates kind.. There is always the option of fitting a 3rd bigger turbo like santjer performance did in the US, over 600whp, check their Facebook page, 5.3s 100-200kph diesel only.
Guys, I have a 2015 BiTdi and Audi say the gearbox is sealed for life. How often should I get the oil in the box changed?
80k miles roughly, we sell the repair kits
@@DarksideDevelopments what’s the best email address to get in touch with you?
Sales@darksidedevelopments.co.uk
Lesson is is always change your oil. ZF say 50-80k
I wish that would fit on a US specs Q5 TDI.
VNT/VGT turbos are so good now, im not sure why audi don't just go single turbo on these? sure im missing something
A big single would be too laggy really
the new Mild Hybrid S tdi models are kind of single turbos 🤷🏼♂️ would be interresting to listen to a Straightpiped s4, s5, s6, s7 tdi
Yeah those are laggy even with 48v supercharger compared to Bi-TDi
And I thought my wife could talk 😂
I talk so she doesn't have to
When I have done the trans is the past I disconnected one of the cooler lines and once I had refilled the system I ran it to pump a litre or so out from the cooler line. I then topped up and repeated until I got clean oil. This pushes the dirty oil out that sits in the torque converter.
Yeah easily done on the bimmers
Hello,
So any more development on this car ?
i have the same car now at the moment stage 2 with 373Hp and 773Nm
We sold the car but will have a new turbo to test at some point!
So much smarter than the ttid saab setup!!
Merch, Rate Then? 😂
my bitdi gearbox was nearly the same at 65k miles (slightly less ferreous on the filter magnets). only strange things i have are clunky changes when cold into first gear. im now changing oil (roughly 4 litres) every year/10kmiles and this keeps the gear changes good. if i dont the clunking comes back. only changed the filter once at 65kmiles. oil comes out mucky every time. mine is mapped to 390hp and runs extremely hot over 4krpm, so i short shift. should really have it remapped to a safe egt limit. your turbo set up has a decent rise across the whole usable rev range, but as you say its going to be expensive for a relatively small gain. bring on the big turbo!! will the gearbox handle 1000nm?? and have your gearbox maps tightened up the first 3 gears? keep it coming! :)
It likes the revs with this turbo. EGT needs to be kept low!
Box will take the power!
Epic Ryan I love a bitdi build 🔥🔥👌
What about launch control in this car? Does it stress the gearbox too much?
From my knowledge the tiptronic isnt meant to work as a launch control. So i wouldnt recomend doing it alot
Nice videos! You won’t get more oil than that from the transmission from just a drain as the torque converter will hold a few litres, but that’s the correct procedure anyway flushing is not really recommended. Also the noise you have is more likely to be the chain/tensioner, very common on these! Look forward to see’ing more developments 👍🏼
It's the ZF procedure. We have a video on the chain fix coming
Not sure if you’re saying its ZF procedure to flush? But it’s not ZF procedure to flush using a machine, this can potentially cause issues. ZF procedure is simply to drain (at correct temps) and refill, to achieve a better/complete oil change you could repeat this process again after a shorter period of time 👍🏼
No, we never flush
Is that power figure at the wheels or at the fly ?
Flywheel
is there a difference in the 3.0 tdi engine and the 3.0 bitdi ? can a c7 a6 3.0 tdi be converted to a 3.0 bitdi without major work ? amazing channel btw !
Lots of work!
@@DarksideDevelopments what single turbo would u reccomend for it ? Can we push 400bhp and 1000nm crank, with other supporting mods like IC, fuel pump etc ? Sorry I'm a noob
Email us, we have the perfect turbo!
Reyt then
What this space then
Great content but let’s get to most important question did your son manage to do donuts with no hands 🙌 lol
Yes, lol
Well explained 👍
Rejt then
Actually 410 bhp you can do with stock turbos, and some good intercooler so figures are not very interesting..
not on our dyno :)
@@DarksideDevelopments i didnt mean to be disrespectful i like how you tune diesels, what do you mean by that not on our dyno, is possible some companies could present figures more “optimistically”?
exactly
All those electronic controls will get knackered and not work properly eventually from all the engine heat.
They seem to be OK.
why 2 when 1 big one would do the same job? yeah it would spool later but who cares
Everyone would care, Inc emissions
whats the cost for 535d 2007 lci two turbos
£2000 or so, email us!
Yes glad we got an update but I’m sure he had it to Audi no so long before he sold it to you for a service and I’m sure there’s a abart 2 years Audi service plan left on it too I do t know how it works with it been tuned now but when he bought it nearly 3 years to the day the original owner bought a 5 year Audi plan just before he sold it lads
It's not going back to Audi, lol!
I wouldn’t be sending it back either with 5 litre of oil being init be I’m more than certain it was done only a few month before you got it but he had a a4 3.0 tdi before the bi and he asked about having Torsen done on that and they said they can’t do it and couldn’t be done literally drove to vw and they did it for him so just shows what theses all singing all dancing warranty’s and service plans a worth dunit
Nice protype turbos
Thank god for electric cars, all these complicated oil burning polluters antiques will be gone.
Lol, and when the electric goes off what you going to do? Please don't buy online either, a diesel ship brings it to a diesel truck and a diesel van delivers it. Small minded sheep walking to the slaughter house...
@@DarksideDevelopments oh the naivety, fella are you not following the new car scene, all the latest and best stuff is either hybrid or fully electric, do you realise how hard it will be to get a diesel vehicle through emissions in the next few years, it will be next to impossible, governments are under severe pressure to rid their country’s of nox particles in the atmosphere,
Let them try! You must be educated
@@DarksideDevelopments. No. I’m a small minded sheep ready for the slaughter,