Dude! This video was great! Helped me find a loose ribbon cable that just had to be clicked in and my phone worked again! Your wonderful step by step instructions gave me the confidence to go at the job.
Just did this.. it takes 8 screws and no need to remove the charging port. In my case the battery was swollen so I did not need to see half of this video about removing the back cover :)
@@kamrannagi3044 you can use the second half of the video. I used some old plastic cards to lift the battery out but this is crazy wel glued in place. Be careful of the ribbon connector that goes over the battery, if your afraid of ripping it you better follow the video guide and remove the lower part as well. After removing the battery it started to boil again by itself so be careful!! Toss it outside or is a salt bath and dispose of as chemical waste.
You are lucky. I tried. There is a plastic film under the glass that came apart, then the glass broke. I wish they would still use good old-fashioned screws to open it for a simple task as changing the battery.
Thanks for this Video! It encouraged me to replace the battery myself. And yep I succeeded! The biggest challenge was to open the back cover because I only had a hair dryer and did not dare to make the lid really hot.
@@3picninjaboy The adhesive and plastic will start to desintegrate, most plastics never boil, they burn before. Additionally electronics in phones are not made to withstand temperatures this high, like the flash which should never ever be heated above 60°C or else it may loose data or just die
Thanks for this video. I was able to replace my swollen battery, the second time this happened on two different make. I think Huawei has a battery swelling problem. Just a suggestion, you may like to include a count of the screws required to be removed from the bottom charging port and the top, motherboard.
Why did you remove the copper colored LCD flex cable? Doesn't look like it impedes the removal of the battery at all. Just for safety since it looks like it's attached to the motherboard?
Thanks, I followed the instruction to replace my battery swelling and it worked but it was really hard to remove the battery. I used an electric oven as a heater. Smok came out from the swelled battery, so I get rid of it quickly.
I mean, do you really need to remove the cover for the charging port and antenna? The battery does not seem to be covered by the antenna and you could just flex the flexkable up a but when removing the battery, right?
bro could u share how did u actually open the back cover? i am having a hard time to open them. i have all the neccessary equipment and all...heat gun, prying tools...but it did not even have any opening when i use the suction...and it became really hot and i am just afraid the heat would damage other parts in the phone itself...the temperature is like really hot till i need to use cloth to hold the phone, yeah it is that hot...LoL...
First of all get a new sticker. Last step is always to stick back panel PROPERLY back because of 2 reasons. 1st if you are just taking back back panel like this it is even falling off after a certain time 2. handset is definitely not waterproof any more this way which is one of the advantages of the phone
unfortunately I can't open back cover, I heated it on a hot plate in different time/temperature combinations Despite use of appropriate suction cup, there was not even a small gap between two parts of phone.
They make it so hard because THEY DON"T WANT YOU to be able to replace the battery and make your phone last another year or two. THEY WANT YOU to buy a new fucking phone. Try finding a smartphone with a removable battery nowadays. They dont want your stuff to last. They want you spending money.
@@theycallmekowalski this is not a manufacturers' exploit though, it is about the market. Stupid people want their phones to be slim but the next day they they will buy a thick silicone case because slim doesnt hold well in hand as well as the need for additional protection. However, for the design to be slim, the manufacturers are forced to use adhesive tapes instead of metal casings and screws etc which would otherwise thicken the phone no more than a silicone case. Remember when iphone released their first slim aspect ratio screen (18:9), people got so crazy about it that every manufacturer followed virtually killing the better 16:9 in every respect in a very short time. It is not always manufacturers fault... the mate 10 pro is a still good example of the above trend which people discarded though the manufacturers would have prefered to keep it out for I suppose economic reasons - I mean, a mini jack port - once they realised the lack of it hits the sales charts, the jack port returned where it should be in newer models - so again - people decided.
Went to a shop and they said there was 85% chance of glass breaking in process of taking back off. Don't know which method they intended to use but it put me off going ahead with battery replacement. Will live with 60% battery capacity for now. Still lasts a day most days.
Hi, I'm from Mexico and I have this cell phone, I need to get the battery and I can't get it here, could you give me a contact and see if you can get it for me, I would appreciate it
Dude! This video was great! Helped me find a loose ribbon cable that just had to be clicked in and my phone worked again! Your wonderful step by step instructions gave me the confidence to go at the job.
You're the man. I couldn't have found out how to replace it by myself. I've done it easy as pie thanks to you. Thank you so much.
😅
Just did this.. it takes 8 screws and no need to remove the charging port. In my case the battery was swollen so I did not need to see half of this video about removing the back cover :)
Hey man, my cover came off too because of the swollen battery. Could you please tell me how did you replace your battery. I'm a complete novice.
@@kamrannagi3044 you can use the second half of the video. I used some old plastic cards to lift the battery out but this is crazy wel glued in place. Be careful of the ribbon connector that goes over the battery, if your afraid of ripping it you better follow the video guide and remove the lower part as well. After removing the battery it started to boil again by itself so be careful!! Toss it outside or is a salt bath and dispose of as chemical waste.
I've removed all the screws after finished asked by myself, why😅
Worked perfectly, was a little bit hard to actually take out the battery cause I only had a hair dryer, but at the end everything worked just fine.
11.00 dollars for the batery and tools and my phone is like new. THANK YOU!!
great video ! i was able to replace my swollen battery and now my phone is as good as new!!! Thanks a lot
Did you have to apply new adhesive to the phone to close it? it doesn't show you did, but other videos show adhesive being reapplied
You are lucky. I tried. There is a plastic film under the glass that came apart, then the glass broke. I wish they would still use good old-fashioned screws to open it for a simple task as changing the battery.
Thanks for this Video! It encouraged me to replace the battery myself. And yep I succeeded! The biggest challenge was to open the back cover because I only had a hair dryer and did not dare to make the lid really hot.
Thank you for the video, it is well done and helped me a lot. saved a lot of money. Wishing you all the best from luxembourg.
Changed my battery using this video, great job and a working phone again 👍
110 degrees celcius, that is a 110 fahrenheit my guy. 110 celcius will fry your phone.
Why would it?
@@3picninjaboy 100 degrees celcius is boiling temperature so it would be really hot.
@@Allan_1462 I know. But its the boiling point of water things like adhesives, plastics etc. have a much higher one.
@@3picninjaboy The adhesive and plastic will start to desintegrate, most plastics never boil, they burn before. Additionally electronics in phones are not made to withstand temperatures this high, like the flash which should never ever be heated above 60°C or else it may loose data or just die
He clearly sets the heat plate to 42 Celcius, that's around 110 Fahrenheit.
Thanks for this video. I was able to replace my swollen battery, the second time this happened on two different make. I think Huawei has a battery swelling problem.
Just a suggestion, you may like to include a count of the screws required to be removed from the bottom charging port and the top, motherboard.
Why did you remove the copper colored LCD flex cable? Doesn't look like it impedes the removal of the battery at all. Just for safety since it looks like it's attached to the motherboard?
Thanks, I followed the instruction to replace my battery swelling and it worked but it was really hard to remove the battery. I used an electric oven as a heater. Smok came out from the swelled battery, so I get rid of it quickly.
It helped a lot!! Thanks for sharing knowledge!!
I mean, do you really need to remove the cover for the charging port and antenna? The battery does not seem to be covered by the antenna and you could just flex the flexkable up a but when removing the battery, right?
When you put back the back cover, do you need to add some glue?
Don't you need to reglue the cover or heat it again when reattaching it to the phone??
yeah I was also thinking about this...
Thanks Serg. Worked like a charm :-)
Where did you get your battery? I can't find an OEM one.
Thank you very much i was about to pay somebody to do it for me but with this video was so easy :D
Thanks you very much, battery replaced!
Do u know if the mate 10 pro battery is exactly the same model as the mate 10 lite?? Thanks!!!
Is it this phone still waterproof after battery replacement?
definitely not anymore. not unless you put a new one
bro could u share how did u actually open the back cover? i am having a hard time to open them. i have all the neccessary equipment and all...heat gun, prying tools...but it did not even have any opening when i use the suction...and it became really hot and i am just afraid the heat would damage other parts in the phone itself...the temperature is like really hot till i need to use cloth to hold the phone, yeah it is that hot...LoL...
what screwdriver did you use?
grazie ottimo tutorial,seguito alla perfezione tutto ok
First of all get a new sticker. Last step is always to stick back panel PROPERLY back because of 2 reasons. 1st if you are just taking back back panel like this it is even falling off after a certain time 2. handset is definitely not waterproof any more this way which is one of the advantages of the phone
can you recommend where to get parts like a battery, a new sticker and what glue to reattach the back cover?
Hey is huawei mate 10pro battery different to huawei mate 10 ?
amazing video thank you so much bro !
Hey Serg, do you have a good supplier for the green spudgers you use? they are my go-to, but they are hard to get.
Thank you very much, dude!!!
super vid, thanks a lot.
thank you very much ! May God bless you
Sehr Gut Danke
Can we this battery for mate 10 lite ? I think the size is same
Tq i made it 🥰
where are the imei on the phone? can you help me? on hardware?
New video. I need a part I can not locate. I have a Samsung s2 tablet.the part i need is the protective backing.do you deal in parts?
excellent
thanks mate
sir i want to change my huawei mate 10 lite battery so which battery i have to purchase what is battery number
HB356687ECW
ringing problem after battery replacement. I need help.
thanks ! you are awesome! (I really need to get another phone though 😂)
Huawei Mate10 pro is explode when battery is going high?
The question is where did you find an original Huawei battery?
I buy original battery and replaced it but its still draining much battery what i do please help
Maybe you have applications that use a lot battery
where to buy new battery except amazon?
ifixit if it still helps you
Thnx!!!!!
unfortunately I can't open back cover, I heated it on a hot plate in different time/temperature combinations
Despite use of appropriate suction cup, there was not even a small gap between two parts of phone.
why the engineer want make the battery so hard to remove?
Purposely make things unfriendly to make job opportunity for phone shop.
They make it so hard because THEY DON"T WANT YOU to be able to replace the battery and make your phone last another year or two. THEY WANT YOU to buy a new fucking phone. Try finding a smartphone with a removable battery nowadays. They dont want your stuff to last. They want you spending money.
@@theycallmekowalski this is not a manufacturers' exploit though, it is about the market. Stupid people want their phones to be slim but the next day they they will buy a thick silicone case because slim doesnt hold well in hand as well as the need for additional protection. However, for the design to be slim, the manufacturers are forced to use adhesive tapes instead of metal casings and screws etc which would otherwise thicken the phone no more than a silicone case. Remember when iphone released their first slim aspect ratio screen (18:9), people got so crazy about it that every manufacturer followed virtually killing the better 16:9 in every respect in a very short time. It is not always manufacturers fault... the mate 10 pro is a still good example of the above trend which people discarded though the manufacturers would have prefered to keep it out for I suppose economic reasons - I mean, a mini jack port - once they realised the lack of it hits the sales charts, the jack port returned where it should be in newer models - so again - people decided.
@@pawelw.9172 stupid people allright
My mate 10 still not charging after replacing port. Any ideas?
Battery
@@Studiotek Hi, I changed the battery yesterday. Got the same issue cannot charge at all...Did you have the same issue? Thanks!
Nice Dear
eh yeah if my battery dies I think I'll just leave it to someone else xD I'm really bad with these small screws and parts
Went to a shop and they said there was 85% chance of glass breaking in process of taking back off. Don't know which method they intended to use but it put me off going ahead with battery replacement. Will live with 60% battery capacity for now. Still lasts a day most days.
Serg this Sam wow !!
mate 10lite battery 🔋 4000mh??????
ans the screen?
I doubt it'll be the same after this...
am from Pakistan i need original Huawei mate pro battery plz
If you wait long enough you battery will get swollen and you can skip step one :D
Errrr, repair shop it is then. Bit too fiddly for me 😭
That must be a new phone. Its totally impossible to remove the backside on my 1½ year old Huawei Mate 10 Pro.
wait until the battery swells... it wil come off by itself.
@@pawelw.9172 😂😂👍
My phone is like these phone put they open and close only idont no way.!
Hi, I'm from Mexico and I have this cell phone, I need to get the battery and I can't get it here, could you give me a contact and see if you can get it for me, I would appreciate it
Better not to buy this shite!
Thats your mothers reaction when she saw you