REDUCER 6" x 5" NA WALANG FORMULA OK KAYA?

DIY style is the way to make without brain stress ,this concentric reducer has two option with formula or without so it is up to you guys where you choose that idea. Fitter on ship and gives ideas for pipe fabrication, welding techniques, overhauling ship machineries ether mechanical or electrical drive , and also lathe machine on how to operates and making various job specially on threading jobs, making flanges, pumps bushing etc. .air condition technician and pipe fitters, making elbows in different degrees and reducer eccentric and concentric and metal fabrication, such as air duct, air venting mushroom and various modification

[@marlietomas4070]

more vids po w/ formula. tnx po sa mga vids mo.

[@shipfitterstv9389]

yes bro i have 133 videos in this channel kung may time ka visit mo ang playlist ko andoon lahat DIY or with formula

[@marlietomas4070]

@@shipfitterstv9389 thank you bro, soon sana bago ako maging fitter, ikaw yung maging senior ko!!!

[@Streetfittergarage]

Sir paano mo nagigitnaan yung mismong tubo. Yung lalayan mo ng center line. Paano mo nakukuha o nasusukat yung pinakagitna ng tubo.

[@shipfitterstv9389]

bro dalang paraan una kumuha ka nga emery cloth san paper na ang lapad ay 50mm the eh wrap mo sa tubo kung anu ang kabouhang sukat or circumference tapos hatiin mo sa apat na parti yong kada kanto ng tupi iyan ang pinaka center mo
at ang pangalawa gumamit ka ng squala halimbawa ang tubo ay may OD na 200 then ang kalahati dyan ay 100 so ang squala idikit mo sa side ng tubo kailangan nala 90 degress position ang squala the kuha ka ng metro or tape measure then idikit mo ang dula ng metro doon sa squala then hanapin mo ang 100mm then guhitan mo iyang ang pinaka center na guhit mo

[@wonderfullifemyqueenandmye4259]

Amorio pa shoutout😁

[@west_costjride33]

Idol pwedi ba gawa ka ng eccentric at concentric na walang formula salamat

[@shipfitterstv9389]

Ang concentric may ginawa na ako dyan hanapin mo sa video ko pero ang eccentric puede namang walang formula kaso matagal gawin kasi puro tantiya lang at saka magastos yan sa ox and acy mas maganda ang formula kasi 95 accuracy

[@christophertabiliran3299]

Sir good morning.anong xlaseng pipe yan ginamit mo sir?

[@shipfitterstv9389]

carbon steel pipe sched 40

[@levimantua5779]

Idol ilang cut sa Malaki na pipe 100A to 50A po?

[@shipfitterstv9389]

6 cuts maganda dyan para maganda ang pagka bilog

[@ramildoroja5377]

Maraming salamat sir idol.

[@shipfitterstv9389]

Welcome bro

[@vietosevillejo774]

Kabakal may sampol ka po 10inch reduce to 4inch elang hate din kabakal

[@shipfitterstv9389]

puede bro kahit 8 na hate pero dapat maiksi ang pagka cone reducer mo na may taas lamang ng 4inches to 5inches

[@christiansy4212]

@shipfittertv paano ba mallaman Yung tamng sukat Ng cone reducer?? Slmat lods more video to come more knowledge s lhat godbless Po

[@jameson9318]

Sir napakagaling nyo Po talaga. Pangalawang sakay ko na as fitter videos nyo Po Ang baon ko combine sa unting knowledge ko. Keep on sharing sir .wish you Goodhealth

[@shipfitterstv9389]

very good bro at na i apply mo ang mga turo ko keep it up and shares mo sa iyong mga kaibigan upang mabigyan sila ng lakas na katulad mo na nakasakay na ng barko

[@shipfitterstv9389]

keep it up bro and shares mo sa mga tropa upang makatulong tayo at maging kagaya rin sila sa iyo na naka sakay na sa barko

[@hamidrezashabani9262]

Hello . I have question for fabricating new pipe when is going to bracing in workshop we have to use gasket between flags or not necessary?

[@shipfitterstv9389]

no sir there no need to put any gasket coz you must to fabricate as new one not by jigs or pattern that is old school style that need the old pipe and make pattern but my idea is i measured the old pipe then i fabricate new then after finish that is the time that i taken out the old pipe so that the time to boxing up it become less

[@hamidrezashabani9262]

Thanks for answering. your method is perfect I should try to fabricating like you.your video is good but if possible try to explain more English egain thanks

[@chogcutamora105]

Sir, dba hndi sinagad ung cutting MO...istimite MO lng ung isang gugit MO..

[@shipfitterstv9389]

Puede naman isagad yan bro iniuring ko lang para maganda tingnan total nakuha naman ang target sa reducer

[@enginemotovlog1906]

Galing sir..panibagong idea na nmn nakuha ko galing sau.. salamat sir sa mga makabuluhang vlog..sana marami kpa maituro..ingat Po lagi..god bless.

[@shipfitterstv9389]

yes bro salamat sa pag subaybay mo sa aking vlog keep it up

[@roxanamorio8932]

💪🏻💪🏻💪🏻

[@magtv6238]

yung pinagkatingan nyu na reducer sir e welding nyu parihas labas at loob?

[@shipfitterstv9389]

Yes bro kung kaya sa penetration pero sa akin kahit may penetration winiwelding ko parin kung maabot para sigurado no leaks