How can we ensure that closing coil gets positive before antupumping relay. Because if AP relay gets positive earlier than closing coil then it will open its NC contact that is in series with closing circuit and hence the closing coil won't get any positive and breaker won't charge. Therefore it is necessary to supply positive to AP relay via two parallel paths one having auxiliary NO contact and other having NO contact of AP relay. PS : The overall explanation is wonderful and very easy to understand. Looking forward to your other videos.
I think the reason to supply parallel path for AP relay is not exactly what you meant. The 52a in the path of the AP contactor is to make sure that the Close coil is not burned out if a user keeps the TNC switch to the Close position even after the CB is closed. Also, the NO contact of the AP contactor which is in series with the AP contactor ckt is for preventing another closing operation if it was closed onto a fault (SOTF condition).
As in your circuit service limit is in NC when DC main on 1st spring charge motor will oparete and spring charge done and the contact will open how the supply pass to coil. Please reply if I am wrong
Join our FB Group, to ask your questions and start a discussion ! Hii Guys, please Join our Facebook Group 'Nitin's Community for Electrical Engineers', to ask anything related to 'Electrical' and especially about 'EHV Power Transmission System'. But please do not post silly questions like posting a photo and asking what is this what is this, its very irritating. Also, no Good Morning, Goodevening or Festival messages please. Link to join the Group is : nitinn.link/elecfbgrpefyt
If the TNC Switch is stuck on C, then a continous pulse is given to the Breaker and if the Breaker Auxillary contact is sluggish, it will burn tge Closing Coil.
THANKS for the video. I have some confusion. The two diagrams you have shown for remote closing. You said that in the first diagram that there is danger to personal working on breaker if breaker is closed remotely. But when switch is at remote position how can the positive be extended to closing coil. If you observe carefully Both the diagrams are correct you have just interchanged the position of TNC and remote switch. At 15:45
In the first Diagram we have used Positive from the relay panel and so if the LR switch is faulty, the DC may get extended to the Breaker. But in the second Diagram , as we are using Breaker positive called as closing positive, when switch off the breaker DC, DC will not get extended.
Sir we are adding antipumping relay across cc and taking its nc contact to protect the breaker hunting effect.but how it is getting continuos supply to make its contact remain open till breaker is on condition.because we are giving only one pulse on that time 94 relay pickup and remain off.how sir
Once the CC is closed by the Close Pulse, the AP contactor will close its contact, whose NO contact is used in series with the AP contactor's coil. This will make sure that the AP contactor is kept in the energized condition until the TNC switch is released.
Sir, please send CT Connection video Two core or 3core CT 1s1, 1s2, 1s3, 1s4 My doubt is I take for metering 1s1 - 1s2 then remaining 1s3 and 1s4 what to do Please reply and also video
Sir, Aap jo ye slide banaye h usko website pe upload kr dijiye please. And thank you sir for your affort to make us knowledgeable towards electrical wiring.
Please continue with such informative sessions
How can we ensure that closing coil gets positive before antupumping relay. Because if AP relay gets positive earlier than closing coil then it will open its NC contact that is in series with closing circuit and hence the closing coil won't get any positive and breaker won't charge. Therefore it is necessary to supply positive to AP relay via two parallel paths one having auxiliary NO contact and other having NO contact of AP relay.
PS : The overall explanation is wonderful and very easy to understand. Looking forward to your other videos.
Yes sir I have seen that in 220 kv breaker scheme. But not in 33 kv breaker.
Thanks for sharing with us though.
I think the reason to supply parallel path for AP relay is not exactly what you meant. The 52a in the path of the AP contactor is to make sure that the Close coil is not burned out if a user keeps the TNC switch to the Close position even after the CB is closed.
Also, the NO contact of the AP contactor which is in series with the AP contactor ckt is for preventing another closing operation if it was closed onto a fault (SOTF condition).
True
As in your circuit service limit is in NC when DC main on 1st spring charge motor will oparete and spring charge done and the contact will open how the supply pass to coil.
Please reply if I am wrong
Dhanyavad sir, khup chhan prakare aapan samjun sangitale , asech video banvat raha .... dhnyavad
Join our FB Group, to ask your questions and start a discussion ! Hii Guys, please Join our Facebook Group 'Nitin's Community for Electrical Engineers', to ask anything related to 'Electrical' and especially about 'EHV Power Transmission System'. But please do not post silly questions like posting a photo and asking what is this what is this, its very irritating. Also, no Good Morning, Goodevening or Festival messages please. Link to join the Group is : nitinn.link/elecfbgrpefyt
Sir,if TNC Switch is stuck both side trip and close and bkr on remote position than closing problem occur ?
If the TNC Switch is stuck on C, then a continous pulse is given to the Breaker and if the Breaker Auxillary contact is sluggish, it will burn tge Closing Coil.
THANKS for the video. I have some confusion. The two diagrams you have shown for remote closing. You said that in the first diagram that there is danger to personal working on breaker if breaker is closed remotely. But when switch is at remote position how can the positive be extended to closing coil. If you observe carefully Both the diagrams are correct you have just interchanged the position of TNC and remote switch. At 15:45
In the first Diagram we have used Positive from the relay panel and so if the LR switch is faulty, the DC may get extended to the Breaker. But in the second Diagram , as we are using Breaker positive called as closing positive, when switch off the breaker DC, DC will not get extended.
@@ELECTRICALFUNDAZ Thanks for the clarification 👍
Outstanding explanation with practical experience
Thanks a million 👍👍👌👌💐💐
Please explain OLTC control circuit if possible....
Great... i am waiting for ferrule like k5 ,k21 (what is the rule for ferrule)
Slowly you will learn them all
Good explain sir
Very nice explain and informative video's keep it up.
Thank you
Great...waiting for trip circuit and spring charging circuit...
Before that you will get to see Troubleshooting Closing circuit problem
very very helpfull video....well explained....drawing is not seen properly
Sir we are adding antipumping relay across cc and taking its nc contact to protect the breaker hunting effect.but how it is getting continuos supply to make its contact remain open till breaker is on condition.because we are giving only one pulse on that time 94 relay pickup and remain off.how sir
Once the CC is closed by the Close Pulse, the AP contactor will close its contact, whose NO contact is used in series with the AP contactor's coil. This will make sure that the AP contactor is kept in the energized condition until the TNC switch is released.
Boss can I get all ansi code related circuit please give me
सर आपका बहुत बहुत धन्यवाद यह वीडियो मेरे लिए बहुत उपयोगी है
सर नमस्कार , 33 के वी CB और कंट्रोल पन्नेल का वायरिंग इंटर कनेक्सन कैसे बनाते है और इसमें क्या क्या ध्यान रखना पड़ता है
Sir 132 kv circuit breaker ka closing ka dragam ka video banaye sir
Sir your explanation is excellent thank-you sir
Good explanation sir.
Sir, please send CT Connection video
Two core or 3core CT
1s1, 1s2, 1s3, 1s4
My doubt is
I take for metering 1s1 - 1s2 then remaining 1s3 and 1s4 what to do
Please reply and also video
If 1S1 and 1S2 are used, 1S3 and 1S4 are to be kept open as Circuit is already completed through the winding between 1S1 and 1S2.
Thanks sir
If, any axillary contact along with 1s1, 1s2, AX, 1s3
What we do auxiliary terminal
We use 1s1 and 1s2 for metering and 2s1and 2s2 for proction
Very nice explain.please make same video for ACB
Sir if you can provide us with the acb bkr drawing, we will make a video.
Very informative video 👌👌Sir...marshalling box to CR Panel, RTCC Panel wiring pe bhi video banaiye please.(40 mva xmer )
Can you please explain TCH
Dear Sir, please watch this video on TCS/TCH th-cam.com/video/CYLK06GeDyM/w-d-xo.html
Sir,
Aap jo ye slide banaye h usko website pe upload kr dijiye please.
And thank you sir for your affort to make us knowledgeable towards electrical wiring.
Sure Sir.
Thanks your dedication Amazing
Very good
Sir please added trip circuit control video
Sir we have a video on TCS please search in our channel
Bhai pls 650 relay n.a. video banau
Thankyou very much sir.
Nice video for us
Very informative
Bhai thank you so much
Thanks a lot bro
Thank you so much sir !
Nice explain
sir, electro- mechanical O/C and E/F relay par ak video banaye...
ok sir.
excellent
Love this video..
Nice
Excellent ..
सर लोकल रिमोट स्विच में प्रैक्टिकल वीडियो बनाएगा प्लीज सर
Ok sir
waiting for elecrical BAHUBALI part-3
Your explanation needs little elaboration in detail, need to restrict current in TNC switch
yes sir we will
मराठीत बनवा की व्हिडिओ
Ok sir, Marathit pan banavu