How to disassemble Singer Brilliance 6199 - C4 Error Fix
ฝัง
- เผยแพร่เมื่อ 8 ก.ย. 2024
- Based on research, one of the most common issues with Singer Brilliance 6199 is the C4 code. If you hear the motor spinning without engaging the hand wheel, the belt must be off the pulley. The only way to fix this is to partially disassemble the machine.
BE CAREFUL not to open it up too much as there is quite a bit of wiring going from the control panel to the base of the machine.
After removing the side cover, remove all screws at the back and the bottom of the machine. Carefully pushing into the back panel at the seam, unhooking it from the front panel.
egorshalvarov.com
I'M SOCIAL HERE:
Facebook: / egorshalvarov
Twitter: / egorshalvarov
Instagram: / egorshalvarov
If you're getting the C4 error, I would suggest to first check the bobbin compartment. See if there any issues with threading, thread obstruction, bobbin case, etc. If all seems okay and the hand wheel is still not responding, the belt might be off so you would need to open up the machine.
When the machine is open, double check on the belt and see if it sits on the pulley (hand wheel) properly. Turn the wheel by hand to see if the motor shaft underneath is being turned by the belt. Make adjustments if needed.
Last resort, plug in the machine while open and GENTLY press on the pedal and see if there are any issues with the whole assembly. If problem still persists, it's time to call the sewing machine technician.
Hope this helps.
Excellent video. It worked wonderfully well. Couldnt have done the job without this video. A small tip: It is important to carefully mark all the screws as they come out because they vary in type and size and you want to put them back in the right place/order.
Such a simple video and soooo HELPFUL! Thank you!
This vid helped so much!! Thank you for posting it!
But man, after taking the screws out, getting that case open is a royal PITA!
Thank you so much I was afraid to open the case that I would break it worse this was so helpful
Ty for the video, I was trying to figure out how to disassemble my Singer 7258, and this helped so much in getting the plastic exterior open.
Thanks so much. Just got this machine (ours is actually called the Singer Fashion mate but it looks exactly the same) Got the C4 error and the first thing I assumed was the belt was off. Your video was extremely helpful especially as you show where the clips are on the case so you don't break them. Actually, we have only had the machine about 4 days so this is a bit of a disappointment, but I had no interest sending it for repair for such a simple issue.
Thanks again,
Ive had my machine for a 1/2 and it came up C4 and was jammed. Phone Wayfair and they told me to destroy machine and they will give me a full refund.
Old Mr.s Singer must be turning in his grave and the junk Singer puts out now.
You have to be a beast and I used pry tools. Then the belt was still on and No thread entanglement. Used my pliers on belt and pulled it hard several times! Finally broke loose. Used can air to blow out our west Texas dirt and oiled it! Now to put it together now it works! Yea me!
Most helpful, I just got into a 6660 which is clipped together in a similar way. That was jammed up with thread around one of the pivots which I carefully removed with tweezers and a craft knife. The video gave me the confidence to pop the cover apart.
Glad it helped.
Gutes Video, zeigt die Problematik genau auf. Nach 20 min lief die Nähmaschine wieder. Danke!!!
Thanks a lot Egor, I saved a couple dollars
Diky za radu...zdravím z Czech republik
Thank you so much! You just made me save 100 € ;)
Gracias me ayudo mucho... Se le había soltado la correa... Graciaas
You make the splitting open look so easy.. Just press with your fingers and pop it opens.
Thanks for the effective help. With your video I fix my singer!!!
Thank you SUPER MAN 😊😊😊
Danke, hat mir sehr geholfen
Excelente. Excelent. It work's and solved my C4 issue. Thanks. Great tutorial
So many thanks for this video
Thanks! Ajudou muito 👍
Thanks, it helped a lot 😁
Thank you so so much!
My Fashion Mate machine had a fall C4 came upon the screen but on opening the left side plastic chamber a metal screw more like a nail fell out.
Bardzo dziekuje
Hi Egorshall, i disassembled the first part of my machine, as there seemed to be a thread stuck. There was a tiny brush that fell out as soon as I took the plastic hood off. It had some lint on it. Do you have any idea where it has come from? I have watched your vid hoping to spot it, but no luck. TIA 👍
Thank you 👍🏼👌🏼😄
Thank you for the fix it worked however the belt still detouches when i try to sew thick materials like jeans is there any other way to make it more secure
I don't think this machine would be able to handle the thick fabric. Just not designed for this kind of stuff.
Mines was doing the same thing I hope my problem is a simple belt fixing
Thank you, thank you.
Alors oui c’est bien ! Mais aux autres personnes qui ont ce souci “C4” ce n’est pas forcément ça!! Si vous arrivez à descendre et monter l’aiguille avec la mollette prévue à cet effet je pense juste que c’est un souci de fil, enlevez-les, remettez-les bien dans le bon sens !! Et si ça fonctionne pas changez d’aiguille et sinon essayez ça mais en dernière option c’est pas super simple donc si c’est fait pour rien ça serait bête! (toujours lire les commentaires parce que j’ai eu peur au début://)
Thank you!!
Merci beaucoup pour cette vidéo. J'ai l'erreur C4, je vais suivre votre vidéo.
Can u please help for E2 error happening while threading bobbin
So I did the exact same thing to mine but the belt wasn't off. And I'm getting the same error again. Any thoughts?
Based on the manual, the C4 code means that the thread is tangled or a bobbin was interrupted forcibly. If none of those apply to your situation, I would also suggest lubricating all movable metal and plastic parts inside the machine.
I think the hook timing on my machine is off. Whenever the needle goes down to the bobbin, it feels like it gets stuck and doesn't pick up the bottom thread. Not sure how to do this and I'm afraid of opening up the machine like you show in the video.
If you're taking your time with this and being careful, you will definitely succeed. Good luck.
EgorShalvarov thank you! I checked the back and it doesn’t seem like the belt has anything wrong with it. So again, I’m stuck. I’m not sure why the bobbin shuttle is getting stuck
I am having the same issue the belt is in place when I use the bobbin winder it moves backwards but not forward please someone help
I have the same machine, same C4 but the belt is on mine
Good morning. I followed the video and currently have my machine pulled apart. I can see that my wheel is spinning one direction but not the other. The belt seems to be on the pully. Any ideas?
I tried following this tutorial, have loosened all the screws, but I just can't get the back open.
The back panel has the "loops" and the front panel has the "hooks". By applying pressure to the back panel at the point of contact, you should be able to release the "loops" from the "hooks". Try rewatching it from 1:50
Hope this helps.
It is very, very difficult. It took me about 40 minutes to finally get the parts to loosen up. I pried it open slightly with a tiny screw driver.
do all sewing machines have drive belts because my sewing machine stopped moving and idk if my drive belt is brooen because it looks like it dowsnt have one
Thames you 🥰
Se puede desarmar por abajo más sencillo
Hallo, leider habe ich den Fadenspannung-Teil geöffnet und den gerafften Faden mit einer Pinzette entfernt, aber ich habe vergessen, wie ich ihn wieder an seinen Platz bringen kann, und dieser Teil passt nicht. Bitte helfen Sie mir und machen Sie ein Bild vom Inneren der Nähmaschine Mein Kanal, danke
Benim makina üst iplik kırıyor çözüm nedir
If wheel will stop them what shall we do
Hi, I have followed your video, discovered the timing belt had a dent. I ordered a new one. Put it in but it wont work... what else do I need to do?
Hi there. I cannot quite picture a "dent" in a timing belt. Have you matched the old and the new timing belts? Are they the same size?
Also, what is the machine doing when you press the pedal?
After fixing the new belt, it's still make the same sound and shows the c4 error. Doesn't sew.
@@kelechilaw7 There might be a thread tangled in a bobbin case. Did you check this by any chance?
No thread. Cleaned the machine
The seller said something about adjusting the motor. But I know that is not possible as the motor is fixed
Can yoh belp me mr how to fix e1 code error on my singer ?
I fallowed everything in the video even went and read comments and the answers and my hand wheel is not budging at all plz help. Thank you.
If you're getting the C4 error, I would suggest to first check the bobbin compartment. See if there any issues with threading, thread obstruction, bobbin case, etc. If all seems okay and the hand wheel is still not responding, the belt might be off so you would need to open up the machine.
When the machine is open, double check on the belt and see if it sits on the pulley (hand wheel) properly. Turn the wheel by hand to see if the motor shaft underneath is being turned by the belt. Make adjustments if needed.
Last resort, plug in the machine while open and GENTLY press on the pedal and see if there are any issues with the whole assembly. If problem persists, it's time to call the sewing machine technician.
Hope it helps.
Thank you for your response. I did all of the above except leaving it open and pressing down in the foot peddle. I will have to try this tomorrow. Will give update once I have done it.
So I took it apart today and pressed down on the foot peddle and looked inside to see where the problem is. The motor turns the band looks good the only thing that is stuck/locked up is the hand wheel.
@@maggiecastillo6901 Looks like you would need to take it to the specialist.
@@maggiecastillo6901 Did you ever find a solution. Did the exact same things as you. The pulley motor turns, but it's the darn hand wheel that won't budge. I haven't used this machine very much and was surprised to have this problem.
Buenísimo me sirve pero sería mejor tradición al castellano gracias
Hey! My singer brilliance totally locked up today! I can’t turn the wheel almost at all, any suggestions on what to try? I’ve taken the bobbin apart and that didn’t help.
Thanks!!
Hey! There could be an issue with the belt and the way it is positioned. You might need to open up the machine.
EgorShalvarov thanks for the reply! My machines opened up and got the handwheel turning perfectly... but the needle bar position is slightly off and now it’s hitting the metal plate. I can’t figure out where to adjust to fix the needle position!
Got to be honest followed the video doesn’t work for me took off all the screws and bolts check 3 time they are all off but the middle section will not come off
Olá alguém poderia me dizer pq o volante da minha máquina travou ela não dá sinal de vida
My belt is on, but the wheel still doesn't move. Doesn't appear to be stuck at the bottom, it just won't turn up or down. Please help someone xXx
When you press the pedal, does anything happen?
Thank you for reply. I just got the grinding noise and c4.
However I took the inside of the bobbin thing apart again and suddenly everything was moving again. I have no idea what I'm doing. But thankfully it is now working. Really appreciated your video xXx
mine has the same problem but it starts to smell like burning, what do you think the problem is?
Different burns have different smells. Does it smell like burning rubber or does it smell like a metal on metal mechanical burn?
it smells like metal burn. is the damaged bad? is it fixable?
@@jhoanna9924 if you're uncomfortable disassembling the machine, I'd suggest taking it to the specialist.
okay, taking it to the specialist will be the best decision to fix this☺. Thankyou ❤
saya dari indonesia saya mendapatkan masalah E4 error di mesin singer futura ce 250 apa yang harus saya lakukan
He either skipped stepps or it's impossible to open this machine.
The latter 😂
What happen cod e6..any suggestion😅😅
Error c3
I hate my machine. She’s on her villain arc I guess even if I always have treated her right.
This machine is crap. I've only used it a handful of times and now it's seized up. It's clean, took it apart, motor that turns the belt works, it's just the hand wheel, like it's welded in place. No way, no how to move it. I'm throwing it out.
QUE RIDICULO NADIE CONOCE NI MUESTRA LA SINGER 7464 Y NADIE HABLA NI MUESTRA PARTES ELECTRONICAS DE LAS MAQUINAS DE COSER PURO TECNICO DE PLASTICO
Thanks for explaining absolutely NOTHING
You are very welcome.