Hello, Thx 🙏 for sharing this! It’s very helpful. I have a questions: The screen is dead in my control panel, can I replace the whole control panel with a second hand that I bought. Or does it need programming?
Hello Khalid Thanks for your appreciation ☺️ You can replace screen with second hand control panel. If you install second hand control panel complete then you will program also.
Hello, engineer, I have a problem with the EMCP 4.1 screen. When it works initially for an hour, the keys work normally, but after a while the keys do not respond to me at all when I press it. I cleaned the chip and also the same problem, please, may I know what is the wrong piece in the electronic board
Hi there is a problem in your ribbon. When your EMCP is running ok for 1hour press two key at a time your controller can't work normally. Ribbon short two key command this is cause of not working of your EMCP
@@faisalshahzad0041 I cleaned the tape very well and cut the end of the tape so that the connection is excellent, but the problem is still the same, and I also changed the entire button board using the Emcp 4.2 button board and still the same problem that occurs in Emcp 4.1 I am absolutely sure that the problem is from the electronic board, but I do not know how to specify from which piece
Sir Sath voice b kren
Good day! How to contact you?
+923000200041 WhatsApp number
how to replace EMCP 4.1
Hi. My emcp 4. 2 is hanging. Any tip to resolve this?
Keypad need to repair for resolve this problem
Hello,
Thx 🙏 for sharing this! It’s very helpful. I have a questions:
The screen is dead in my control panel, can I replace the whole control panel with a second hand that I bought. Or does it need programming?
Hello Khalid
Thanks for your appreciation ☺️
You can replace screen with second hand control panel.
If you install second hand control panel complete then you will program also.
Please send you numbers sir
Mr Feisal I have 4.2 the problem is the screen no shown did u change
Necesito el Diagrama de Conexion electrica
Greetings, excuse me, it also works for a power wizard 1.1 Olympia board and what voltage in DC do you put on it?
Yes pin out are same!
And 8 to 32 v DC voltage ,
I put 24 voltage DC
Very useful
Hello, engineer, I have a problem with the EMCP 4.1 screen. When it works initially for an hour, the keys work normally, but after a while the keys do not respond to me at all when I press it. I cleaned the chip and also the same problem, please, may I know what is the wrong piece in the electronic board
Hi
there is a problem in your ribbon.
When your EMCP is running ok for 1hour press two key at a time your controller can't work normally.
Ribbon short two key command this is cause of not working of your EMCP
@@faisalshahzad0041 I cleaned the tape very well and cut the end of the tape so that the connection is excellent, but the problem is still the same, and I also changed the entire button board using the Emcp 4.2 button board and still the same problem that occurs in Emcp 4.1 I am absolutely sure that the problem is from the electronic board, but I do not know how to specify from which piece
@@abdualkadershuga1163 maybe front keys couldn't make contact
@@faisalshahzad0041 The front key bar is very well connected to the electronic board, and I checked with a FLUOK voltmeter tester
hi please help me where i can buy the EMCP 4.2 button board
How to solve the emcp error button won't be pressed, boss
Need to replace keypad to solve this.
Hi I have two control panel it has sem problem
Ok send to me
@@faisalshahzad0041 how can I connect with you
@@سالماحمد-غ3ن +923000200041 WhatsApp number
السلام عليكم
Walekum assalam
Nice wahtsapp nambar send karai
03000200041