@@OUHSSAINESAID-LightingDesign Dear sir, is there a specific lighting standard for outdoor carpark ? I guess that in Dialuxevo, its abt 20lux depending on situation. Is there a IEC or other standards we could use for reference ? Thank you.
@@andrewlaksh7931 Actually, it depends on the standard you need to respect. For example, in the european standards, it can be either 20, 10 or 5 lux, depending on the traffic load. You can find all that in DIALux evo in the "Spaces" tab.
@@OUHSSAINESAID-LightingDesign Greetings to you sir. I have gone through all the for set of videos that you had shared here for free and i was fortunate to have got hold of the videos and to date I have not seen anyone who share their CAD drawings and to use it to flow your guide in the videos step by step. Thank you very much. In one of my projects, I used a jpg. file imported into DIALux Evo. It is a lighting simulation for landscaping and public area at a riverside. But the divisions of assessment zones were not prominent in the drawing. I tried partitioning the drawing into assessment using polygonal floor element in DIALux but the area defined by the polygonal lines didnt form a floor element and hence my lighting simulation didnt work out. Thus, I have a question that I hope you can answer. If the division of zones in the drawing is not well defined, and we estimate a rough floor area and insert lighting fixtures, this floor area doesnt form a solid floor and hence, DIALux would not be able to preform the operation? Thank you in advance sir.
Hi I have a problem in dialux. Can you help in this regard? I import auto cad drawing to dialux and do the design. Then again I need to import revised auto cad drawing. I removed the previous one and import the new one. But the new drawing was out of range of my design. So how should I arrange the coordinates to have the new drawing onto the previous design?
Hi, Here is how to solve that : Go to the verical tab "PLANS" click on the new plan in the section "PLANS" in "ADDED PLANS" --> go to "POSITIONING" and click on "MOVE PLAN", then click on a part on the new plan you can recognize in your existing building! That will bring the new plan on top of your project. The best way to that tho is to replace the plan instead of uploading a new one (in case it's the same that you modifed). I hope you understand Good luck
How does one account for a change in grade in a project site? For example, illuminating a long stairway running from one work area on a hill to another work area at the bottom, for an outside facility.
It is actually easy to do! I refer you to this video on how to make stairs : th-cam.com/video/D0IVeulbGMk/w-d-xo.html&ab_channel=OUHSSAINESAID Here is also a playlst for beginners : th-cam.com/play/PLxzYBVew8KyI-3j7SCwHLcyMf6EIpehdy.html If you have any question, don't hesitate :)
Hello Respected Sir, I am working on a project at our hospital which includes shifting of pole solar lights to pole flood lights because of poor lighting and performance of these solar ligths. Sir, we have the boundary wall around the hospital buildings which lengths 531meter south wall, 440meter northside boudary wall and approximately 220 meter each each and west boudary walls. We have 62 poles already installed for solar lights what i am going to do is to replace solar lights with phillips 100w flood lights to improve serveillance and security of the hospital boundary wall and i do not have any site plans to import into dialux evo 12.1. Please suggest me for having proper working on this project at dialux. Bundle of thanks
Hello OUHSSAINE SAID, I can't find the DWG plan ,it's showing like file does not exist please check the URL. Can you please verify it and upload again Thank you.
Thanks @Nader Al-Fekri for your comment! Here is the link for the CAD file! (The luminaires are already inserted, but you can use it like that anyways) drive.google.com/file/d/1vUMS-NdjsllPZD0kudx9zRv19ny-HqSL/view?usp=sharing
I am just learning this software thanks for your instructional video. However when I follow along with you and create floor elements there is no option for running calculations on them. I have to create a calculation surface in order to run calculations. Am I missing something?
In order to be able to start a calculation, you need to insert lights first ! Inserting calculation surfaces is optional, but it's what let's you know about the achieved lighting levels!
🚀 JOIN MY FREE DIALux evo TRAINING: said-ouhssaine-s-school.teachable.com/p/free-dialux-evo-course
Thank you for all these free video tutorial guides!
Very welcome. I am looking forward to add more and more content to help all those people struggling out there...
@@OUHSSAINESAID-LightingDesign Dear sir, is there a specific lighting standard for outdoor carpark ? I guess that in Dialuxevo, its abt 20lux depending on situation. Is there a IEC or other standards we could use for reference ? Thank you.
@@andrewlaksh7931 Actually, it depends on the standard you need to respect. For example, in the european standards, it can be either 20, 10 or 5 lux, depending on the traffic load. You can find all that in DIALux evo in the "Spaces" tab.
@@OUHSSAINESAID-LightingDesign Tq sir.
@@OUHSSAINESAID-LightingDesign Greetings to you sir. I have gone through all the for set of videos that you had shared here for free and i was fortunate to have got hold of the videos and to date I have not seen anyone who share their CAD drawings and to use it to flow your guide in the videos step by step. Thank you very much.
In one of my projects, I used a jpg. file imported into DIALux Evo. It is a lighting simulation for landscaping and public area at a riverside. But the divisions of assessment zones were not prominent in the drawing. I tried partitioning the drawing into assessment using polygonal floor element in DIALux but the area defined by the polygonal lines didnt form a floor element and hence my lighting simulation didnt work out.
Thus, I have a question that I hope you can answer. If the division of zones in the drawing is not well defined, and we estimate a rough floor area and insert lighting fixtures, this floor area doesnt form a solid floor and hence, DIALux would not be able to preform the operation? Thank you in advance sir.
Hi I have a problem in dialux. Can you help in this regard?
I import auto cad drawing to dialux and do the design. Then again I need to import revised auto cad drawing. I removed the previous one and import the new one. But the new drawing was out of range of my design. So how should I arrange the coordinates to have the new drawing onto the previous design?
Hi,
Here is how to solve that :
Go to the verical tab "PLANS" click on the new plan in the section "PLANS" in "ADDED PLANS" --> go to "POSITIONING" and click on "MOVE PLAN", then click on a part on the new plan you can recognize in your existing building! That will bring the new plan on top of your project.
The best way to that tho is to replace the plan instead of uploading a new one (in case it's the same that you modifed).
I hope you understand
Good luck
I understood. Thanks 👍
@@sajeevipiumika4033 You're welome!
How does one account for a change in grade in a project site? For example, illuminating a long stairway running from one work area on a hill to another work area at the bottom, for an outside facility.
It is actually easy to do! I refer you to this video on how to make stairs :
th-cam.com/video/D0IVeulbGMk/w-d-xo.html&ab_channel=OUHSSAINESAID
Here is also a playlst for beginners :
th-cam.com/play/PLxzYBVew8KyI-3j7SCwHLcyMf6EIpehdy.html
If you have any question, don't hesitate :)
Excuse me sir, I want to ask for a design on Dialux, do you have to have a 3D dwg design or can you also have a 2D design? Thank you
You can actually start a project in 2D or 3D. It depends on what plans you have !
Hello Respected Sir,
I am working on a project at our hospital which includes shifting of pole solar lights to pole flood lights because of poor lighting and performance of these solar ligths.
Sir, we have the boundary wall around the hospital buildings which lengths 531meter south wall, 440meter northside boudary wall and approximately 220 meter each each and west boudary walls.
We have 62 poles already installed for solar lights what i am going to do is to replace solar lights with phillips 100w flood lights to improve serveillance and security of the hospital boundary wall and i do not have any site plans to import into dialux evo 12.1.
Please suggest me for having proper working on this project at dialux.
Bundle of thanks
hjola , podrias compartir el enlace. gracias.
Hi can I get the CAD drawing link..Thankyou
Hi sir, can you please share the DWG file link
the dwg file not available
salut c intéressant mais le fichier drvie dwg n'accède pas essayer de le repartager
Merci
Essaye ce lien :
drive.google.com/file/d/1vUMS-NdjsllPZD0kudx9zRv19ny-HqSL/view?usp=sharing
@@OUHSSAINESAID-LightingDesign avez vous des formations en Français pour nous autres qui ont un peu de difficulté avec l'anglais
@@hoffmanaman4570 Oui, y a des vidéos en français, même si ce n'est pas assez. Voilà le lien :
th-cam.com/play/PLxzYBVew8KyITJ9pY3bbweryUFPKdS4xT.html
@@OUHSSAINESAID-LightingDesign merci 🙏
Hello OUHSSAINE SAID,
I can't find the DWG plan ,it's showing like file does not exist please check the URL. Can you please verify it and upload again
Thank you.
Hi,
Try this out :
drive.google.com/file/d/1vUMS-NdjsllPZD0kudx9zRv19ny-HqSL/view?usp=sharing
Good luck
Thanks a lot for this great effort. would you please share the CAD file again, I couldn't find it.
Thanks @Nader Al-Fekri for your comment!
Here is the link for the CAD file! (The luminaires are already inserted, but you can use it like that anyways)
drive.google.com/file/d/1vUMS-NdjsllPZD0kudx9zRv19ny-HqSL/view?usp=sharing
@@OUHSSAINESAID-LightingDesignMany Thanks
@@naderal-feki3940 anytime 😊
Hi, I am trying to download the DWG file, but the link is showing the error 'file does not exist'.
Hi,
Try this out :
drive.google.com/file/d/1vUMS-NdjsllPZD0kudx9zRv19ny-HqSL/view?usp=sharing
Good luck
I am just learning this software thanks for your instructional video. However when I follow along with you and create floor elements there is no option for running calculations on them. I have to create a calculation surface in order to run calculations. Am I missing something?
In order to be able to start a calculation, you need to insert lights first !
Inserting calculation surfaces is optional, but it's what let's you know about the achieved lighting levels!
Excelente demostración , me agradaría conocer el siguiente video , donde me supongo se iluminaran las diferentes areas . gracias
Gracias por tu comentario!
Los siguientes videos ya están en mi canal!
Aqui esta el link : th-cam.com/play/PLxzYBVew8KyJntaa_lHKqwzWTSHKb22L7.html
file doesn't exit plz send me link.
Here is the link to the plan : we.tl/t-8sMHO7lvg7
Thank you and we wait for mor
Welcome, and thank you too for your kind comment :)
There will be new tutorials every Tuesday, stay tuned ;)
in shaa allah
Hi, DWG is missing in the drive
Hi,
Try this out :
drive.google.com/file/d/1vUMS-NdjsllPZD0kudx9zRv19ny-HqSL/view?usp=sharing
@@OUHSSAINESAID-LightingDesign Thank you, God bless you
@@karishmaraj6168 Very glad I can help!
Let me know if you have any questions
Great work
Thank you
Thank u Man
Welcome !
I hope it helped :)
@@OUHSSAINESAID-LightingDesign Yeaah Man , it's helpful that's exactly what i need right now:) :) waiting for the second part with passion
@@abderahmaneddayyani1041 Wait for it, it'll be here next week ;)
نتمنى دير شي دورة باللغة العربية
Ghadi nttkrfess, ou nnass maktarch! walakin 3lach lla! ndirha Htta b Tamazight!