LaserCube WiFi - Quick Start Guide - Setup and Operation

International LaserCube WiFi version shown.
FDA-compliant US version features an e-stop:
• How To Connect LaserCu...
Hello! Let’s get started setting up your lasercube.
Warning: Lasers are dangerous. Make sure to completely read and understand all safety guidelines before operating your laser.
Installing the Lasercube
Make sure the laser does not project onto people or other animals.
Make sure the beam blocker is closed when handling the lasercube for charging, installing, or transporting.
The internal battery should be charged before use. If the lasercube is installed in a difficult location for the power chord to reach, make sure to charge it before installing.
No cables are required to operate the lasercube, but if you wish to keep the power cable plugged in during use or are using a wired LAN connection, make sure all cables are fastened securely.
Install the laser at a height of 3 meters or 10 feet above anywhere people may be present.
To fasten your lasercube, use the tripod mount located on the bottom of the lasercube, and any adapters needed to attach it firmly to your support structure.
An eye bolt is provided for additional support to prevent damage or injury from dropping your lasercube.
Once the Lasercube is securely installed, connect the antenna, safety jumper, and key.
While positioned behind the lasercube, reach around and lower the beam blocker.
Turn on the power switch, and turn the key until the two white lights turn on. It is now ready for operation.
Network Connection
There are several ways of connecting your control device (iphone, android, pc, or mac) to your lasercube.
By default, the lasercube is in WiFi server mode.
In WiFi server mode, the lasercube acts as a 2.4GHz wireless network named “LaserCube” with a password Laser2020 which is case sensitive.
Connect to the Lasercube network with the settings on your control device.
The connection status LED next to the antenna will flash while waiting for a connection, or will remain constantly lit when connected.
To switch connection modes, press and hold the mode button until the lasercube projects the connection mode.
An asterisk will be displayed next to the mode the lasercube is currently set to.
To switch modes, single-press the mode button until the desired mode is displayed, then hold down the mode button until the lasercube restarts.
To connect in WiFi client mode, hold down the mode button until the current mode is displayed, then single-press the mode button until WiFi client is displayed.
Press and hold the mode button until the status LED turns white. It is now ready to connect to your WPS network router.
Press the WPS button on your router.
When connected successfully, the status LED on the lasercube will turn solid blue.
Many connection modes will be covered in a separate video.
Installing Laseros
Install Laseros on your device from the app store, the play store, or laseros.com
Once installed, start Laseros and it should detect any lasercubes on the network you’re connected to.
On a smartphone, if the play arrow is blue it means you’re connected to the lasercube.
If it’s greyed out, check your connection and try again.
On a mac or windows pc, laseros will display “Laser Off” in the upper left side above the preview panel when connected correctly.
If not, it will display “no laser”.
When you’re ready to project a laser show, switch to “laser on” or tap the play button on a smartphone.
If the lasercube is projecting into areas you wish to protect, you can use the beam blocker to cut off the lower projections.
You can also set safety zones within the projection area from the settings menu.
This is also covered in a separate video:
Lasers Safety Zones - How It Works - How To Set it Up
• Lasers Safety Zones - ...
Thank you for safely using the Lasercube. Enjoy the show!
💥Follow Us On💥
/ wicked_lasers
/ wickedlasers
/ wickedlasers
👉 You can find us also here:
►Website: wickedlasers.com​
►Website: laseros.com

[@SilesiaLasers]

Great video! It will be very helpful for many new users 🤘🏻 great 🔥

[@gangadhar.talari]

Price sir

[@fred7flinstone]

What is the story for connecting to WIFI without WPS? Not all routers support WPS... my EERO system included.

[@wickedlasersvids]

If proper credentials were provided to LaserCube’s firmware settings, then, LaserCube should connect to that router automatically.

[@xophaser]

what laser goggles nm should we wear in case the laser hits the eye.

[@wickedlasersvids]

LaserCube is using 3 laser diodes - 445nm, 520nm and 635nm.

[@xophaser]

@@wickedlasersvids thank you

[@ccboss490]

Can you ship to NY?

[@wickedlasersvids]

No, but we have US distributor. Please visit www.x-laser.com

[@PurnaMix]

Your best laser but very money 😭😭😭😢🥺😞😞😞🇮🇳🇮🇳🇮🇳🇮🇳🇮🇳

[@PurnaMix]

Love from india 🇮🇳🇮🇳no money 😭😭😭😭😭😭😭😢😢😢😢