Hey Mike, been liking your videos, keep up the good work! Had a couple suggestions, hope you don't mind. 1) I don't know if you've heard, but there's increasing doubt around what's really going on with the retrobrite process, and a lot of people now believe that it causes irreversible damage and plastic embrittlement. I think on something like a CD ROM faceplate it really doesn't matter (it's not like it's likely to get much pressure put on it, and they're far from irreplaceable) but there's a good chance it could actually bleach away the printing. If your channel starts really popping off - here's hoping - you'll probably get people in your comments being very negative if you don't include some kind of disclaimer that it's not necessarily recommended for all applications anymore. 2) regarding that first ATX power supply, usually when I see dead supplies, it's just 0 volts across the board, so I wonder if that one is old enough that it won't bring up the voltage rails until it has a load on it. That's more common with even older supplies, but it's always worth checking before discarding a PSU - keep a couple unimportant hard drives or a motherboard you don't care much about, and plug them in just to give it some load and you'll get a more accurate test. keep rockin!
Thanks so much! I definitely have much research to do on the retrobrite process. In the back of my mind I was kind of suspicious of it, especially with regard to decals. I appreciate the heads-up! I had forgotten that some older PSUs did load-sensing. Just tried the PSU with a deceased (yet still current-hungry) hard drive connected, but no such luck. Maybe I’ll do a ‘deep dive into a troubled power supply’ video and explore what’s going on at the circuit-level. I should spring for an actual power supply tester to do proper cromulence checks in the future. Thanks for all the info!
Can't say I've seen an ATX power supply that required a load to start. A bigger problem I have been having with some mid-00s Seasonic (Antec branded) units is that they lose the ability to power themselves on from a motherboard. +5VSB seems to be working fine, but may be weak enough to not be able to drive the relay that triggers the PS_ON pin. If the machine is of any value, I would try and find a newer unit. These machines don't have ISA bus slots so the lack of -5V power is a non-issue. Just be mindful of the +5V rail rating. Pre-P4 machines relied far more on +5V to drive devices and the CPU.
Hey there! On the matter of retrobrite and similar techniques to remove yellowing from plastics, I will say that some of these concerns have been around for quite a while, but I think those concerns may have grown louder. I'm coming at it from a toy-collecting angle, since yellowing plastics are a major issue to collectors of vintage toys, and some people have reported that issues with embrittlement, and others have reported that they rapidly start to yellow again. I haven't looked into it for 3 or 4 years, but the concerns that were voiced at the time were enough to put me off the idea.
Hey Mike / Gravis! I’ve done some research on whitening some of the old PC Cases that I’ve got here, Found something called “CARA White” here in the UK & it’s also used in the Caravan / Camping industry over here, I’ve whitened a few Cases now and have had some pretty decent results but it’s a bit early to tell if if has caused irreparable damage as I did it to mine back in 2020 during Lockdown but I’ve not had any problems so far, Ah so that’s where he got the idea using the Hard Drives as a Load for when he’s Testing the PSUs! 🙂🇬🇧
My first introduction to computers came via "Lost In Space" re-runs(original air dates: 1965-68) via the Robot and on-board computers. These videos "compute"! Thanks!
@@miketech1024 Ah yes, but a noisier time, an error-prone time, a dead spider time, a 'I won't boot til you give me what I want, and even then I still won't boot' time. 🙂
Those hinge cracks were very common on Acer laptops, they would progress until the screen broke off of the hinges because the hinges did not continue further up the screen. i'm guessing the Gateway brand is constructed the same.
TH-cam recommended your channel to me. From the quality of the content I assumed you had a few hundred thousand subs like most channels youtube recommends. After you mentioned about the sudden growth, I checked your subs and was shocked you had less rhan 2k... Your channel will grow substantially. Trust me. Very interesting content (for the retro nerds like me) and well executed.
Thank you so much! It’s crazy to think that less than two weeks ago I had under 200 subscribers. Now I’m closing in on 2000! Needless to say I’ve been feeling like I’m on top of the world lately! 🙂
I worked at Gateway during the Windows 98/Me era, these cases were our best. Every employee wanted to get one of these for themselves because they were so nice to work on. I hope it survives and cleans up well. CDROM 'bus' connector is 40-pin, which implies it is standard IDE. 'metal support bars from the keycaps', these are called 'stabilizers', or as the cool kids call them, 'stabs'.
I am a major fan of these cases, there were only two drawbacks, one was the power supply opening, if the internal ps died there wasn't an easy way to just get a standard one and put it in there, same with the motherboard, usually a dremel had to be involved. otherwise these could be really cool sleeper builds.
Matsushita used a proprietary 40 pin bus back in the early 90's. The connector is physically but not electronically compatible with IDE. Those early Creative drives were often rebranded Matsushitas.
@@robert1975031 Their earlier mATX minitowers at least used standard SFX PSUs, they were just put in the dumbest spot imaginable right above the mainboard blocking any kind of easy access without removing said PSU, if you had, say, an Essential 433c kicking around whose hard drive died, you could stick a modern mATX mainboard and SFX PSU in there and have a decent sleeper build. I would see about modding the front of the case to take a 120mm fan though so that something like a P12 redux-1700 PWM fan could be installed to compensate for the relative lack of front air intake on that case, and IIRC the exhaust can be a 92mm on that case design.
The thumb screw in the middle of the gateway motherboard is in fact stock. And is also the only securing screw. The rest of the standoffs are threaded brass pegs that connect to slots cut into the motherboard mounting panel. You remove the thumbscrew then the whole motherboard slides to the side away from the back panel and lifts out.
I have a Microsoft keyboard just like that on my in my office at work, still working perfectly. I also used to have a dell system just like that one back in the day. I recall having Windows 2000 on it, though I remember it starting with Windows 98 or something.
Watched some of the videos I missed back to back for about 3 hours I literal couldn’t get up to make a drink glued to it Love your stuff Dave London uk
Good stuff! I especially like your editing. You speed up or skip the time consuming tasks and GET RIGHT TO THE POINT! I'm sure it takes some time to do tihs and is MUCH APPRECIATED!
I have an old dell laptop tucked away for about 4 years now. Last time I booted it, it worked fine it has wifi internet floppy and battery. It's a pentium 3 512 gb ram 40 gb hdd win 2000 last time I powered it up it still worked perfectly even the battery.
It does appear this PSU is trying to sense a load. However, I later tried using a few sacrificial hard drives with no success. I’ll likely do a ‘deep dive into a troubled PSU’ video to see what’s going on at the circuit-level. Love your channel BTW! It’s one of my favorites!
Just stumbled across this channel purely by accident and am SO glad I did! Everything is explained really clearly and some of the gear brings back some good memories from my past tech years. Mike is also super hot, so that’s a bonus! 😜
Love these time capsule PC's and how the memories come flooding back, of things not seen , or used in years, like AOL etc.. what a trip!! and no nicotine glaze on, or in them lol
I really appreciate your kind efforts in making such informative content, you clearly have the intelligence and tenacity for working with vintage computers . God Bless you Sir
I know this is an older video, but my brother used to own a Gateway tower that looked identical the first one. I can’t remember the specs of it, but I believe it was a P3 as well and came with WinMe. The power supply failed on his as well, except it was within a few years of it being new. Thankfully it didn’t take anything with it, so he just plopped a new PSU in it and kept using it.
I love those Microsoft keyboards, I found a NOS about a year ago for less than $20, I was probably more excited than I should have been but whatever. great video as usual.
YT algrorythm brought me here. Your channel is nice. Fun to watch. I am 53. Had similar PC's back in the day. Threw away so many after I just said "Hell with it" and just bought a new one. Now that I can build my own today? Looking back then, I probably could had saved myself some money back in those days and they lasted me much longer! LOL And yeah, Anytime you throw stuff away, Make sure you purge all that stuff out people!! LOL
I hear you on the anxiety! Same problem with me due to some serious health issues I have. The videos help me too and often can push me into getting involved into my PC and electronics interests once again when my health allows. Be well yourself and feel better! 👍👍❤❤
The CR-563-B was definitely not an IDE drive. That 40-pin connector was for a 8-bit proprietary bus made by Panasonic/Matsushita. Luckily, plugging it into an IDE controller wouldn't hurt it, but nothing would work on that channel (if not the whole system) since it ties a lot IDE signals to ground.
Wow, this video really takes me back! In the early 2000s I had a paying hobby of buying machines like these, refurbishing them, and (occasionally) selling them. The ones I was getting were mostly Pentium IIs (remember the old single-edge stand-up processors?). My prize find is a K-Mart branded "Blue Light Special" tower, which I still have. Oh, and the one I found with a bird nest inside, where the power supply had been left out!
Nice! I was doing the same thing in the early 2000s, mostly with laptops. I had to lie to eBay to get the account because I was only 12 years old lol. I still use that same account! Wow! If I came across a Blue Light Special tower, I just might need medical attention! 🤣
I miss those internet keyboards. Especially the ones with media playback buttons on them. AFAIK the extended keyboard API is still supported in both Windows and Linux, it's a shame it's not well used anymore
I enjoy watching you. Your comments make me laugh, specialty when you said just looking at that CPU makes me sneeze. lol I used to build those computers and I have a lot of old computer parts most work some don't would you be interested in them for free?
Most definitely! I'm always in need of components. Can you send me an email? You can find the address in the channel about page under Business Inquiry. Thanks!
I have that Gateway, the case is so annoying to deal with because of that weird slot thing and the way the drives get stuck in the bays. Maybe I’ll get a new case for mine at some point since it’s in rough condition anyway, although I like the way it looks.
the power supply on that dell was made (marked at least) in the exactly same day i was born, so, this is at least 22 years old, and in better state than i am
When I get an old IBM Compatible computer, I first try to rescue the pron, then the MP3's and the stored books, next is looking for remnants of bitcoin. Luckily the passwords only protect Windows™ from starting up and not the data. Weird pron they had in those days, elderly women dressed as schoolgirls, it smells even dusty.
I have the Dell Demension L866R in storage, great Family PC. 20 years ago and still have all the restore discs. Made changes and additions to the machine: CD burner, usb 2.0 card, 80 GB hdd, 256 MB ram, external DVD burner, ethernet card.
Knoppix!! the hero live OS that saved my ass more times than i can remember (Looking right at you Winblows). Adore the channel, love the systems, got some real old but gold here. Im kinda jealous of your 200+ system haul you did. I would love to find a haul like that, my wife though, not so much haha! :)
Funny thing about a spider, it will build a web in a place that logically no other insect will visit, and then perish from hunger. BTW, I have that exact same Asus monitor on my desk!
FYI compressed air will not cause any static issues on a mainboard. Not sure why you think it would be an issue. Just unplug any fans before blowing them off with compressed air to prevent your fans from becoming a generator if you do blast them with air. In the 30+ years I have been tinkering (including a number of years as a sys admin) not once have I had a board get killed by compressed air. Cheers!
Refreshing to see vintage computer enthusiasts who actually know how to use Linux. Also I'm glad to know I'm not crazy for saying Dells are the easiest machines to service. Their laptops even today are way easier than the rest, the bottom cover pops up automatically. My time at Geek Squad last year made me go from hating Dell to recommending them to others. I remember when they used to suck in the mid 2000s.
I remember when I disassembled my old PC. My harddrive had failed. I took it completely apart, took the platters and FULLY annihilated them. So many scratches and dents and holes punched into them. I took the parts to bestbuy to get recycled and they said "I think you did too much for us to recycle that. Just throw it away."
i have boxes and boxes of cards from a business i had in NY up until the late 90s...i just cant bring myself to tossing these once expensive cards in the trash as well as several dozen motherboards a big box of hard drives, even SCSI drives jazz drives tape drives and lots more ive forgotten about lol
I’d love to see what you have, and maybe negotiate a deal if you’re willing to sell. Could you send me an email? You can find my email address in the channel about page under ‘business inquiry’.
The GoBack utility from Norton was a fantastic tool back in the day that allowed you to roll a disk image back to a previous state. For instance, if you installed the new driver or update and it goofed up Windows to the point it would not boot. The GoBack would revert the drive back to its previous state.
Have to say your videos are addictive, not sure why I like old computers so much but I do. Of all the prebuilts back then I kinda liked Gateway, they were just pretty normal hardware most of the time... no silly proprietary stuff that I can remember and their cases were pretty high quality. Immediately saw you were right about that Creative CD-ROM drive, I got a drive that looked exactly like that in a bundle around 1993 I think. 2x and Matsushita/Panasonic interface, I think they came with a Sound Blaster Pro and later a Sound Blaster 16 that had the special interface. Wonder how it ended up in there?
i have that same keyboard, it was the first keyboard ive ever had 21 years ago. somehow miraculously managed to keep it in functioning condition. i got a motherboard with ps2 just so i can use it.
Awesome finds! I had an L series many years ago that I got second hand with all the manuals and documentation. Came in a big box, it was quite a treat to go through.
One tip, always hold fan when u blow dust out because you can destroy beaings if you spin it too fast, and that old fans are even more prone to go bad. I like your chanel, i also repair and colect old computes from pentium era and it`s nice to see someone else gives them love not just to 8 bit machines :)
Some Windows machines will automatically disable the network card if Windows does not detect a valid network signal. You have to reboot the computer with a good network connection plugged in.
man, I would have done anything to have this gateway laptop when I was 12, I remember one time watching my cousin play rogue spear on his laptop his parents got him while we were driving and I thought it was the most crazy thing ever to be able to play games on a computer that was totally mobile.
I just found my mom's old PC from the late-90's in the garage the other day... I cannot wait to restore it. It's a Pionex brand PC which I know for a fact she bought off of QVC or HSN lol, and I guess some crypto company is now using that name so it's almost impossible to find any documentation on it.
@@miketech1024 basically on-board everything except a soundcard and ethernet card which looks like something I might've done back in the... it's a Pentium III system (probably 600Mhz and also the mobo has a separate PGA370 socket) with one 256MB RAM module jumpered for 100MHz FSB. No hard drive (not sure what happened there) and a CD-ROM which I'm guessing is probably a 40X and apparently also has a PCI express slot! I haven't taken it apart completely yet because the plastic on the case is SUPER fragile plus I need to grab some compressed air for it first to give it a good cleaning.
Very nice. I actually have the exact same motherboard as the one in the Gateway tower, I use it as my test bench for various P3 era hardware (CPUs, memory, PCI cards etc). It's nice that it has its onboard video so if I test something else I don't need to plug in a VGA card, but I can also use it for testing AGP and PCI video cards if I want to.
28:08 Dude! I got a Dell too! A dark grey and green accented P4 clamshell from like 1998, or thereabouts! The really classic one that everybody's mom had! I can't wait to turn it into a gaming powerhouse!
New subscriber here. I agree with the sentiment here that your channel will grow quickly. I am 54, and started in computers with my younger brother's Commodore Vic-20 in about 1981. My first computer was a Timex-Sinclair 1000 a year or two later, but I didn't get my first "PC" until late 1994 when my brother gave me his no longer used 386DX25 clone. Never looked back! I am increasingly sorry that I gave away my large pile of 1990s era PC hardware, about 10+ years ago.
Always used compressed air to clean the insides of my PCs, never yet had any trouble, or static in general, knock on wood. Did manage to blow up my Chinese power source once as it had a sliding switch for different voltages. That was . . . interesting. Heard the bang to the farthest room. Even then the other parts functioned normally.
37:00 the procedure for fixing this, back in the day, was usually to do a recovery boot from a win2k cd. Run chkdsk and the usual round of MBR / bootloader fixes from there. It's likely that an IBD blue screen is due to a messed up boot sector.
just found this channel and love these types of videos.. i was never around when those computers were new an up to date but i love retro things like this! keep up the good work man your videos and explanation of these things are awesome
Whenever I get a vintage pc, I always keep the o/s install that's on it (when possible) for authenticity's sake, and just delete any personal info that's on it. I suppose if someone else got ahold of the computer they could find a way to recover those files, but the chances of that actually happening is very, very slim
Yeah I like to keep the original OS whenever possible. Yes it’s trivially easy to recover deleted files. When the OS deletes a file, it’s really only deleting the file header and marking the allocated space as safe to overwrite. On systems which I have no recovery image for, I’ll either use a file-shredding utility to get rid of user data, or I’ll simply delete the files and then fill the entire disk with data. That causes the OS to overwrite the contents of the deleted files.
First of all, it's worth noting how hot you are, and secondly, your videos are truly relaxing while also evoking a nostalgia for a good time when I fell in love with computers. If there was a career as a PC archaeologist, I would definitely apply for a position. I love the channel, please keep uploading videos.
I came across a Solo 5300 recently as well! Needed a little work but got it all fixed up and in the hands of a new owner who was eager to do some retro gaming! Really liking your Channel, learning a lot! Subscribed.
Hey Cutie, where’d you get your experience and education? I also admire your patience for takings things completely apart and putting them back together perfectly. I’d lose my patience the moment something didn’t fit right.
@@miketech1024 that’s like me except I got into them in the mid 90s in my early teens. I never had any formal training with them due to the math (calculus and that witch craft) requirements to get into college courses. Just self-taught.
The right side bar in windows ME on the first PC was the MS office toolbar had completely forgotten about it, it was optional during installation MS office 97 - 2003 ish, not seen that for a while.
Good to know the gateway can handle the web no problem 😆 I have one of those dells I picked up at a thrift store some time ago but it’s missing the side panel unfortunately. It did have the matching crt but I passed it on to an old friend who was hunting for years for one but couldn’t find one locally. Hopefully I can figure out a solution to make a side panel or something.
I really want to start collecting but I have like no space maybe that’s for the better though because I would be poking through everything on the drives lmao
Dude, I just want to say, I love your rainbow watch!!! Sweet dude, SWEET!!!
I'm so glad I found this channel! Love going down the memory lane, to simpler times.
Hey Mike, been liking your videos, keep up the good work! Had a couple suggestions, hope you don't mind.
1) I don't know if you've heard, but there's increasing doubt around what's really going on with the retrobrite process, and a lot of people now believe that it causes irreversible damage and plastic embrittlement. I think on something like a CD ROM faceplate it really doesn't matter (it's not like it's likely to get much pressure put on it, and they're far from irreplaceable) but there's a good chance it could actually bleach away the printing. If your channel starts really popping off - here's hoping - you'll probably get people in your comments being very negative if you don't include some kind of disclaimer that it's not necessarily recommended for all applications anymore.
2) regarding that first ATX power supply, usually when I see dead supplies, it's just 0 volts across the board, so I wonder if that one is old enough that it won't bring up the voltage rails until it has a load on it. That's more common with even older supplies, but it's always worth checking before discarding a PSU - keep a couple unimportant hard drives or a motherboard you don't care much about, and plug them in just to give it some load and you'll get a more accurate test.
keep rockin!
Thanks so much! I definitely have much research to do on the retrobrite process. In the back of my mind I was kind of suspicious of it, especially with regard to decals. I appreciate the heads-up!
I had forgotten that some older PSUs did load-sensing. Just tried the PSU with a deceased (yet still current-hungry) hard drive connected, but no such luck. Maybe I’ll do a ‘deep dive into a troubled power supply’ video and explore what’s going on at the circuit-level. I should spring for an actual power supply tester to do proper cromulence checks in the future.
Thanks for all the info!
Can't say I've seen an ATX power supply that required a load to start. A bigger problem I have been having with some mid-00s Seasonic (Antec branded) units is that they lose the ability to power themselves on from a motherboard. +5VSB seems to be working fine, but may be weak enough to not be able to drive the relay that triggers the PS_ON pin.
If the machine is of any value, I would try and find a newer unit. These machines don't have ISA bus slots so the lack of -5V power is a non-issue. Just be mindful of the +5V rail rating. Pre-P4 machines relied far more on +5V to drive devices and the CPU.
Hey there! On the matter of retrobrite and similar techniques to remove yellowing from plastics, I will say that some of these concerns have been around for quite a while, but I think those concerns may have grown louder. I'm coming at it from a toy-collecting angle, since yellowing plastics are a major issue to collectors of vintage toys, and some people have reported that issues with embrittlement, and others have reported that they rapidly start to yellow again. I haven't looked into it for 3 or 4 years, but the concerns that were voiced at the time were enough to put me off the idea.
Hey Mike / Gravis!
I’ve done some research on whitening some of the old PC Cases that I’ve got here, Found something called “CARA White” here in the UK & it’s also used in the Caravan / Camping industry over here, I’ve whitened a few Cases now and have had some pretty decent results but it’s a bit early to tell if if has caused irreparable damage as I did it to mine back in 2020 during Lockdown but I’ve not had any problems so far,
Ah so that’s where he got the idea using the Hard Drives as a Load for when he’s Testing the PSUs! 🙂🇬🇧
Came for the gun show, stayed for the tech talk
Can't decide what's sexier, the host or the tech! 😀
@@marcberm The host! I mean, hot damn...
Same 😅 He knew what he was doing when he made that thumbnail haha
Exactly
i usually re-watch certain parts of his videos 😉
My first introduction to computers came via "Lost In Space" re-runs(original air dates: 1965-68) via the Robot and on-board computers. These videos "compute"! Thanks!
It's fascinating to me to see all these old computers and their programs even though I lived through their era lol.
They remind me of a simpler time. 🙂
@@miketech1024 Ah yes, but a noisier time, an error-prone time, a dead spider time, a 'I won't boot til you give me what I want, and even then I still won't boot' time. 🙂
@@miketech1024but was an interesting time too! Even peripherals like mice and keyboard selections were great.
Those hinge cracks were very common on Acer laptops, they would progress until the screen broke off of the hinges because the hinges did not continue further up the screen. i'm guessing the Gateway brand is constructed the same.
TH-cam recommended your channel to me. From the quality of the content I assumed you had a few hundred thousand subs like most channels youtube recommends. After you mentioned about the sudden growth, I checked your subs and was shocked you had less rhan 2k...
Your channel will grow substantially. Trust me. Very interesting content (for the retro nerds like me) and well executed.
Thank you so much! It’s crazy to think that less than two weeks ago I had under 200 subscribers. Now I’m closing in on 2000! Needless to say I’ve been feeling like I’m on top of the world lately! 🙂
He is very very awesome, as are his videos, which, while very good to start with keep getting better and better each time!
I worked at Gateway during the Windows 98/Me era, these cases were our best. Every employee wanted to get one of these for themselves because they were so nice to work on. I hope it survives and cleans up well. CDROM 'bus' connector is 40-pin, which implies it is standard IDE. 'metal support bars from the keycaps', these are called 'stabilizers', or as the cool kids call them, 'stabs'.
I am a major fan of these cases, there were only two drawbacks, one was the power supply opening, if the internal ps died there wasn't an easy way to just get a standard one and put it in there, same with the motherboard, usually a dremel had to be involved. otherwise these could be really cool sleeper builds.
Unlike the other Gateway case of the time period that had the power button that always broke and fell into the case.
Matsushita used a proprietary 40 pin bus back in the early 90's. The connector is physically but not electronically compatible with IDE. Those early Creative drives were often rebranded Matsushitas.
@@robert1975031 Their earlier mATX minitowers at least used standard SFX PSUs, they were just put in the dumbest spot imaginable right above the mainboard blocking any kind of easy access without removing said PSU, if you had, say, an Essential 433c kicking around whose hard drive died, you could stick a modern mATX mainboard and SFX PSU in there and have a decent sleeper build. I would see about modding the front of the case to take a 120mm fan though so that something like a P12 redux-1700 PWM fan could be installed to compensate for the relative lack of front air intake on that case, and IIRC the exhaust can be a 92mm on that case design.
so you see how gateway fuck up amiga division first hand
The thumb screw in the middle of the gateway motherboard is in fact stock. And is also the only securing screw. The rest of the standoffs are threaded brass pegs that connect to slots cut into the motherboard mounting panel. You remove the thumbscrew then the whole motherboard slides to the side away from the back panel and lifts out.
I have a Microsoft keyboard just like that on my in my office at work, still working perfectly.
I also used to have a dell system just like that one back in the day. I recall having Windows 2000 on it, though I remember it starting with Windows 98 or something.
i have a feeling you'd be a dope friend i could talk about tech stuff without boring you to death xD
I had to Chuckle at: 44:57 “In a Holiday TupperWare Container that I definitely didn’t forget to return to my Mum’s House!” 😂🇬🇧
That's a lot of hard drive spice. My hard drive in my mid-2000s computer was of 88 Gb.
Like the cool stuff you find it’s really cool to geek on retro tech
Watched some of the videos I missed back to back for about 3 hours I literal couldn’t get up to make a drink glued to it
Love your stuff
Dave
London uk
Good stuff! I especially like your editing. You speed up or skip the time consuming tasks and GET RIGHT TO THE POINT! I'm sure it takes some time to do tihs and is MUCH APPRECIATED!
you have much better luck than I have. I've been looking at thrifts and yard sales for a year and haven't found any computers
I'm glad you can appreciate a crunchy hard drive, often feel like I'm alone in that sentiment!
I have an old dell laptop tucked away for about 4 years now. Last time I booted it, it worked fine it has wifi internet floppy and battery. It's a pentium 3 512 gb ram 40 gb hdd win 2000 last time I powered it up it still worked perfectly even the battery.
Most older PC power supplies require a load in order to start up.
It does appear this PSU is trying to sense a load. However, I later tried using a few sacrificial hard drives with no success. I’ll likely do a ‘deep dive into a troubled PSU’ video to see what’s going on at the circuit-level. Love your channel BTW! It’s one of my favorites!
Just stumbled across this channel purely by accident and am SO glad I did! Everything is explained really clearly and some of the gear brings back some good memories from my past tech years.
Mike is also super hot, so that’s a bonus! 😜
I love watching you encountering the different 8 legged murder bugs. Thanks, Mike, your channel is really entertaining!
Thanks!!
Love these time capsule PC's and how the memories come flooding back, of things not seen , or used in years, like AOL etc.. what a trip!! and no nicotine glaze on, or in them lol
the keyboard is fantastic
I really appreciate your kind efforts in making such informative content, you clearly have the intelligence and tenacity for working with vintage computers . God Bless you Sir
Thank you so much!!
Garage sales "expeditions" ! Well done Sir ! Nothing like to go out there into the wild in search of prized game !
I know this is an older video, but my brother used to own a Gateway tower that looked identical the first one. I can’t remember the specs of it, but I believe it was a P3 as well and came with WinMe. The power supply failed on his as well, except it was within a few years of it being new. Thankfully it didn’t take anything with it, so he just plopped a new PSU in it and kept using it.
Definitely an old person computer after seeing that AOL favorites lol
I love those Microsoft keyboards, I found a NOS about a year ago for less than $20, I was probably more excited than I should have been but whatever. great video as usual.
YT algrorythm brought me here. Your channel is nice. Fun to watch. I am 53. Had similar PC's back in the day. Threw away so many after I just said "Hell with it" and just bought a new one. Now that I can build my own today? Looking back then, I probably could had saved myself some money back in those days and they lasted me much longer! LOL And yeah, Anytime you throw stuff away, Make sure you purge all that stuff out people!! LOL
Your videos are very interesting. They actually help calm my anxiety lol. Keep creating such great content ❤️ It's fun for me to learn something new.
I hear you on the anxiety! Same problem with me due to some serious health issues I have. The videos help me too and often can push me into getting involved into my PC and electronics interests once again when my health allows. Be well yourself and feel better! 👍👍❤❤
The CR-563-B was definitely not an IDE drive. That 40-pin connector was for a 8-bit proprietary bus made by Panasonic/Matsushita. Luckily, plugging it into an IDE controller wouldn't hurt it, but nothing would work on that channel (if not the whole system) since it ties a lot IDE signals to ground.
I remember those days and evenings with older era PC's. I really like your fantastic videos keep up the excellent work.
Thanks!
Wow, this video really takes me back! In the early 2000s I had a paying hobby of buying machines like these, refurbishing them, and (occasionally) selling them. The ones I was getting were mostly Pentium IIs (remember the old single-edge stand-up processors?). My prize find is a K-Mart branded "Blue Light Special" tower, which I still have. Oh, and the one I found with a bird nest inside, where the power supply had been left out!
Nice! I was doing the same thing in the early 2000s, mostly with laptops. I had to lie to eBay to get the account because I was only 12 years old lol. I still use that same account! Wow! If I came across a Blue Light Special tower, I just might need medical attention! 🤣
The windows start-up sound brought back a LOT of memories.
Ive got that same dell and the gateway tower and a gateway solo pro 9300
45:17 the duck! 🤣
Glad you remembered the most important thing to have while cleaning the keyboard, a purple rubber duck.
I miss those internet keyboards. Especially the ones with media playback buttons on them. AFAIK the extended keyboard API is still supported in both Windows and Linux, it's a shame it's not well used anymore
Keep up the good work, nice to see the old machines again i used to work a lot with these in my early tech days!
I enjoy watching you. Your comments make me laugh, specialty when you said just looking at that CPU makes me sneeze. lol I used to build those computers and I have a lot of old computer parts most work some don't would you be interested in them for free?
Most definitely! I'm always in need of components. Can you send me an email? You can find the address in the channel about page under Business Inquiry. Thanks!
I have that Gateway, the case is so annoying to deal with because of that weird slot thing and the way the drives get stuck in the bays. Maybe I’ll get a new case for mine at some point since it’s in rough condition anyway, although I like the way it looks.
the power supply on that dell was made (marked at least) in the exactly same day i was born, so, this is at least 22 years old, and in better state than i am
Who could forget, “Dude! You’re getting a Dell!”
love these videos Mike, calming and cool
When I get an old IBM Compatible computer, I first try to rescue the pron, then the MP3's and the stored books, next is looking for remnants of bitcoin. Luckily the passwords only protect Windows™ from starting up and not the data. Weird pron they had in those days, elderly women dressed as schoolgirls, it smells even dusty.
I have the Dell Demension L866R in storage, great Family PC. 20 years ago and still have all the restore discs. Made changes and additions to the machine: CD burner, usb 2.0 card, 80 GB hdd, 256 MB ram, external DVD burner, ethernet card.
Nice! Those restore discs can be quite hard to find. I always upload ISO images of them to Archive.org whenever I find them.
Knoppix!! the hero live OS that saved my ass more times than i can remember (Looking right at you Winblows). Adore the channel, love the systems, got some real old but gold here. Im kinda jealous of your 200+ system haul you did. I would love to find a haul like that, my wife though, not so much haha! :)
Thanks! Knoppix will always have a place in my toolkit, and my heart.
Funny thing about a spider, it will build a web in a place that logically no other insect will visit, and then perish from hunger. BTW, I have that exact same Asus monitor on my desk!
I know Apple didn’t badge thier computers with OS and cpu labels but now I really want to.
FYI compressed air will not cause any static issues on a mainboard. Not sure why you think it would be an issue. Just unplug any fans before blowing them off with compressed air to prevent your fans from becoming a generator if you do blast them with air. In the 30+ years I have been tinkering (including a number of years as a sys admin) not once have I had a board get killed by compressed air.
Cheers!
AOL was a real burst of nostalgia. The Windows XP / AOL 7.0 days were iconic.
Now I wanna play some Slingo! 🤣
That AOL part was, as the Clash would've said, a letter forwarded from Hell.
i enjoyed watching your video, brought back many memories
I really enjoy watching your channel, it brings back a lot of memories. Thanks for sharing with us.
Refreshing to see vintage computer enthusiasts who actually know how to use Linux. Also I'm glad to know I'm not crazy for saying Dells are the easiest machines to service. Their laptops even today are way easier than the rest, the bottom cover pops up automatically. My time at Geek Squad last year made me go from hating Dell to recommending them to others. I remember when they used to suck in the mid 2000s.
I remember when I disassembled my old PC. My harddrive had failed. I took it completely apart, took the platters and FULLY annihilated them. So many scratches and dents and holes punched into them. I took the parts to bestbuy to get recycled and they said "I think you did too much for us to recycle that. Just throw it away."
i have boxes and boxes of cards from a business i had in NY up until the late 90s...i just cant bring myself to tossing these once expensive cards in the trash as well as several dozen motherboards a big box of hard drives, even SCSI drives jazz drives tape drives and lots more ive forgotten about lol
I’d love to see what you have, and maybe negotiate a deal if you’re willing to sell. Could you send me an email? You can find my email address in the channel about page under ‘business inquiry’.
The GoBack utility from Norton was a fantastic tool back in the day that allowed you to roll a disk image back to a previous state. For instance, if you installed the new driver or update and it goofed up Windows to the point it would not boot. The GoBack would revert the drive back to its previous state.
Have to say your videos are addictive, not sure why I like old computers so much but I do.
Of all the prebuilts back then I kinda liked Gateway, they were just pretty normal hardware most of the time... no silly proprietary stuff that I can remember and their cases were pretty high quality.
Immediately saw you were right about that Creative CD-ROM drive, I got a drive that looked exactly like that in a bundle around 1993 I think. 2x and Matsushita/Panasonic interface, I think they came with a Sound Blaster Pro and later a Sound Blaster 16 that had the special interface. Wonder how it ended up in there?
i have that same keyboard, it was the first keyboard ive ever had 21 years ago. somehow miraculously managed to keep it in functioning condition. i got a motherboard with ps2 just so i can use it.
Pretty Nice!
Awesome finds! I had an L series many years ago that I got second hand with all the manuals and documentation. Came in a big box, it was quite a treat to go through.
Those old desktops sure are a product of their eras.
Love your videos. Very interesting to watch and love your commentary.
Keep up the amazing work man
Aahhh I’m use to my Tupperware and utensils being sacrificed.😂
One tip, always hold fan when u blow dust out because you can destroy beaings if you spin it too fast, and that old fans are even more prone to go bad. I like your chanel, i also repair and colect old computes from pentium era and it`s nice to see someone else gives them love not just to 8 bit machines :)
Yeah I held it in place, but I cut the footage because I thought the sound would annoy people. This is my favorite era of computing!
Some Windows machines will automatically disable the network card if Windows does not detect a valid network signal. You have to reboot the computer with a good network connection plugged in.
I see Rub-A-Dub-Ducky came back for a visit.
He goes where he is needed the most!
man, I would have done anything to have this gateway laptop when I was 12, I remember one time watching my cousin play rogue spear on his laptop his parents got him while we were driving and I thought it was the most crazy thing ever to be able to play games on a computer that was totally mobile.
Hey! Looking forward to meeting you. Can't wait to see what you fixup!
I just found my mom's old PC from the late-90's in the garage the other day... I cannot wait to restore it. It's a Pionex brand PC which I know for a fact she bought off of QVC or HSN lol, and I guess some crypto company is now using that name so it's almost impossible to find any documentation on it.
I live for niche systems like that! What are the specs?
@@miketech1024 basically on-board everything except a soundcard and ethernet card which looks like something I might've done back in the... it's a Pentium III system (probably 600Mhz and also the mobo has a separate PGA370 socket) with one 256MB RAM module jumpered for 100MHz FSB. No hard drive (not sure what happened there) and a CD-ROM which I'm guessing is probably a 40X and apparently also has a PCI express slot! I haven't taken it apart completely yet because the plastic on the case is SUPER fragile plus I need to grab some compressed air for it first to give it a good cleaning.
@@livefreeprintguns buy a cheap little compressor , no need to buy air in a can again .
Very nice. I actually have the exact same motherboard as the one in the Gateway tower, I use it as my test bench for various P3 era hardware (CPUs, memory, PCI cards etc). It's nice that it has its onboard video so if I test something else I don't need to plug in a VGA card, but I can also use it for testing AGP and PCI video cards if I want to.
28:08 Dude! I got a Dell too! A dark grey and green accented P4 clamshell from like 1998, or thereabouts! The really classic one that everybody's mom had! I can't wait to turn it into a gaming powerhouse!
Holy shit, it's probably a SCSI cdrom drive!!!!
the plug protected the rj45 during travel or storage
That travelstar HDD and the floppy drive in the gateway laptop sound very similar to the old Sony Vaio FX-220 that i owned before. So much memory man.
17:14 we need spindle HDD ASMR videos
New subscriber here. I agree with the sentiment here that your channel will grow quickly.
I am 54, and started in computers with my younger brother's Commodore Vic-20 in about 1981. My first computer was a Timex-Sinclair 1000 a year or two later, but I didn't get my first "PC" until late 1994 when my brother gave me his no longer used 386DX25 clone. Never looked back!
I am increasingly sorry that I gave away my large pile of 1990s era PC hardware, about 10+ years ago.
Thanks! Yeah I wish I still owned even 25% of the stuff I had as a kid! So much early IBM PC stuff… Now it’s all SO expensive! Hurts to think about.
Always used compressed air to clean the insides of my PCs, never yet had any trouble, or static in general, knock on wood. Did manage to blow up my Chinese power source once as it had a sliding switch for different voltages. That was . . . interesting. Heard the bang to the farthest room. Even then the other parts functioned normally.
Las Gateway son muy buenas tuve uno pero tuve que venderlo era un Pentium 4 478 en memoria dimm lo cambien a 865 y le calzo exacto 😊
37:00 the procedure for fixing this, back in the day, was usually to do a recovery boot from a win2k cd. Run chkdsk and the usual round of MBR / bootloader fixes from there. It's likely that an IBD blue screen is due to a messed up boot sector.
If I remember correctly, and I'm probably wrong haha, but I faintly remember being able to use a windows XP install disc to repair win2k boot sector.
Really enjoyed the knowledge you shared on the CLI and shell scripting in Linux.
A good haul!👍👍
what do you do with all these old devices you refurbish?
Currently I just keep them, but I’ll have to start selling them eventually.
just found this channel and love these types of videos.. i was never around when those computers were new an up to date but i love retro things like this! keep up the good work man your videos and explanation of these things are awesome
Thanks so much!
Whenever I get a vintage pc, I always keep the o/s install that's on it (when possible) for authenticity's sake, and just delete any personal info that's on it. I suppose if someone else got ahold of the computer they could find a way to recover those files, but the chances of that actually happening is very, very slim
Yeah I like to keep the original OS whenever possible. Yes it’s trivially easy to recover deleted files. When the OS deletes a file, it’s really only deleting the file header and marking the allocated space as safe to overwrite. On systems which I have no recovery image for, I’ll either use a file-shredding utility to get rid of user data, or I’ll simply delete the files and then fill the entire disk with data. That causes the OS to overwrite the contents of the deleted files.
Cool video. I remember those days. Thank you.
quality for pc sleeper🤩🤩🤩🤩
Love your channel. Old tech brings back memories. I used to tinker alot when I was a kid too.. New sub 🌈
Just remember eBay completed listings are not sold listings. There are two filters
14:30
"WE HAVE TO GO BACK" - Jack Shepard 😁
First of all, it's worth noting how hot you are, and secondly, your videos are truly relaxing while also evoking a nostalgia for a good time when I fell in love with computers. If there was a career as a PC archaeologist, I would definitely apply for a position.
I love the channel, please keep uploading videos.
Thanks!! Yeah these systems take me right back to a simpler time. 🙂
I came across a Solo 5300 recently as well! Needed a little work but got it all fixed up and in the hands of a new owner who was eager to do some retro gaming! Really liking your Channel, learning a lot! Subscribed.
Hey Cutie, where’d you get your experience and education? I also admire your patience for takings things completely apart and putting them back together perfectly. I’d lose my patience the moment something didn’t fit right.
Thanks! I’ve just been doing it since early childhood, starting around age 5. Nearly a lifelong thing for me.
@@miketech1024 that’s like me except I got into them in the mid 90s in my early teens. I never had any formal training with them due to the math (calculus and that witch craft) requirements to get into college courses. Just self-taught.
Really nice laptop find for only 20 bucks.
The right side bar in windows ME on the first PC was the MS office toolbar had completely forgotten about it, it was optional during installation MS office 97 - 2003 ish, not seen that for a while.
Good to know the gateway can handle the web no problem 😆 I have one of those dells I picked up at a thrift store some time ago but it’s missing the side panel unfortunately. It did have the matching crt but I passed it on to an old friend who was hunting for years for one but couldn’t find one locally. Hopefully I can figure out a solution to make a side panel or something.
I really want to start collecting but I have like no space maybe that’s for the better though because I would be poking through everything on the drives lmao